Stands - Abba vs Warrior?
Discussion
Hey, at least it's not a "which gloves" thread.
I want to replace my steering head bearings, refresh the forks etc so I'm after a stand which will enable me to get the front wheel off the ground. In the past I've used a paddock stand on the back and suspended the front using ratchet straps from a beam in the garage but that never seemed very stable and I wouldn't fancy having the bike swing about while I'm trying to get bearing races out.
I have been thinking about getting the Abba stand with the front lift kit, but I've just seen the warrior stand ( http://www.demon-tweeks.co.uk/motorcycle/bike-lift...) which also looks like it would do a good job and would come to about the same price (£150ish).
Anybody used either/both? Which would you recommend, and are there any other alternatives I should consider?
I want to replace my steering head bearings, refresh the forks etc so I'm after a stand which will enable me to get the front wheel off the ground. In the past I've used a paddock stand on the back and suspended the front using ratchet straps from a beam in the garage but that never seemed very stable and I wouldn't fancy having the bike swing about while I'm trying to get bearing races out.
I have been thinking about getting the Abba stand with the front lift kit, but I've just seen the warrior stand ( http://www.demon-tweeks.co.uk/motorcycle/bike-lift...) which also looks like it would do a good job and would come to about the same price (£150ish).
Anybody used either/both? Which would you recommend, and are there any other alternatives I should consider?
Abba user here, used the front lift kit to do the same job. Only criticisms are once the front wheel is off the ground and rocking the forks,They is play. Which makes it difficult to access the play in the bearings or bushes. Also takes a fair old pull on the strap to lift the front wheel clear. But that may be just my bike, speed triple. But I've got a way of making it easier by putting my foot inside of the rear wheel and pushing down.
Thank you, gentle denizens of Biker Banter, it looks like it's going to be an Abba for me.
I did a bit more searching and found some reports of the bike "drooping" to the right on the Warrior stand, plus quite a few people seem to have had problems setting the stand up in the first place. I can see how the Warrior might be better if you want to move the bike around when on the stand, maximise storage space etc but that's not what I'm after.
Cheers, will let you know how the bearing change/fork refresh goes.
I did a bit more searching and found some reports of the bike "drooping" to the right on the Warrior stand, plus quite a few people seem to have had problems setting the stand up in the first place. I can see how the Warrior might be better if you want to move the bike around when on the stand, maximise storage space etc but that's not what I'm after.
Cheers, will let you know how the bearing change/fork refresh goes.
Years ago I knocked up a copy of the ABBA stand at work in about an hour, it would have taken me a lot longer to copy the Warrior stand so I bought one. The stand came with Warrior and Bursig stickers on it. Either the Chinese were taking the piss or there was something in the rumour that they were both made in the same factory.
anonymous said:
[redacted]
Sounds about right. IIRC there was a pre somewhere in the original instructions about not over tightening, so it's something I'm always mindful of. First time I've used it on this bike, as it has a centre stand, and it appears to have twisted slightly and got wedged in.abarber said:
Quite a few bikes have Hex nuts on both ends of the swingarm pivots, like my R1-Z, or H1E etc. I use my Abba stand on a lot of different bikes and it would help with some of them.
It's been discussed in the past, some people have made up sets for themselves.
You can get proper Abba adapters for solid swingarm bolts.It's been discussed in the past, some people have made up sets for themselves.
After using an Abba stand I'd never go back to using a regular paddock stand for maintenance (I've also had a bike roll off a paddock stand whilst working on it). With the Abba stand, the weight is centred so it's much easier to lift the front wheel with a front stand as there's very little weight on the front wheel. They frequently pop up for sale on Fleabay, I picked mine up together with the correct adaptors for my 1994 Blade for £50 delivered.


Edited by Gunk on Saturday 9th July 13:49
Sorry to dig this up, I'm thinking about buying an abba stand and i wanted to know if anyone else uses the combination of an abba stand and a front paddock stand (like Gunk posted above) ? If you do, how well does this work? I wanted a setup that i could leave the bike on for a longish time, and i am not sure how happy i would be using the abba front lift kit for longer peroids of time. Any help would be much appreciated.
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff



