Replacement Wing Panels e39
Discussion
Hi,
My e39 is showing blistering of the paint along the rim of the top of the wheel arches. I am guessing that if I get the dremel out it will only end badly (much more rust lurking in that area) so thought about just replacing the entire panels.
Does anybody know of a place to get replacement panels other than through BMW and is this something anybody here has done to solve a rust problem. Do patern parts generally fit okay?
Going by MOT the rest of the chassis is sound so the bits showing are more cosmetic than anything. The idea is just to run it until the rust becomes an MOT issue and then swap them, at which point it would be good to have a spare set in the workshop just needing spraying and fitting.
Thanks in advance for advice.
My e39 is showing blistering of the paint along the rim of the top of the wheel arches. I am guessing that if I get the dremel out it will only end badly (much more rust lurking in that area) so thought about just replacing the entire panels.
Does anybody know of a place to get replacement panels other than through BMW and is this something anybody here has done to solve a rust problem. Do patern parts generally fit okay?
Going by MOT the rest of the chassis is sound so the bits showing are more cosmetic than anything. The idea is just to run it until the rust becomes an MOT issue and then swap them, at which point it would be good to have a spare set in the workshop just needing spraying and fitting.
Thanks in advance for advice.
If it's the front wings then it is possible to pick them up secondhand from a breaker. If you shop carefully you should be able to get some that are relatively rust-free. The front wings come off quite easily once the plastic wheel arch liners have been removed. I did a bit of a light-touch DIY resto of the bodywork of my E39 530d in the summer of 2015 (there's a thread in 'Readers' Cars' about it) but wished I'd sourced second-hand front wings instead of spending a lot of time buzzing the rot off mine and doing the inevitable filling etc. etc.. At the time I saw some pretty good used OE front wings for about £40 each (from memory) but if you take this route you'll need to be quite choosy.
If your rear wheel arches are badly shot you're choices are limited to cutting out the rot and bodging a repair with fibreglass & filler (like I did!) or fabricating and letting in new metal. You could buy the complete rear quarter of the car as a new part from BMW if you wanted to but that wouldn't make economic sense! There may be some aftermarket rear wheel arch patch repair panels available but I didn't come across any in my quest last year.
(Have a really close look at your jacking points as severe rot here will kill the car. The sill covers can hide all sorts of horrors!)
If your rear wheel arches are badly shot you're choices are limited to cutting out the rot and bodging a repair with fibreglass & filler (like I did!) or fabricating and letting in new metal. You could buy the complete rear quarter of the car as a new part from BMW if you wanted to but that wouldn't make economic sense! There may be some aftermarket rear wheel arch patch repair panels available but I didn't come across any in my quest last year.
(Have a really close look at your jacking points as severe rot here will kill the car. The sill covers can hide all sorts of horrors!)
roofer - you've not seen my dremel work! Never ends well!
Thanks for tips regarding replacement panels - idealy looking for new if I can get them for a good price (patern parts) as it will need spraying anyway plus the days of hunting round scrappies is something I don't have the time for. Unless you know of any that specialise in BMW parts?
Car was up on the ramp not long ago and no crunching from the rear arches - but a bit to scared to have a proper root around! It's a touring model so not sure if they have the same problems at the rear for rust.
Many thanks,
Thanks for tips regarding replacement panels - idealy looking for new if I can get them for a good price (patern parts) as it will need spraying anyway plus the days of hunting round scrappies is something I don't have the time for. Unless you know of any that specialise in BMW parts?
Car was up on the ramp not long ago and no crunching from the rear arches - but a bit to scared to have a proper root around! It's a touring model so not sure if they have the same problems at the rear for rust.
Many thanks,
Edited by pistonheadforum on Sunday 2nd October 21:36
I got mine from here http://www.ebay.co.uk/itm/BMW-5-SERIES-E39-1996-20... They're new painted pattern parts and the finish is great. The fit isnt quite right, it's a few mm proud at the head lamp but that may be down to my ham fistedness & not properly aligning it rather than the product itself. It is good enough for a daily shed though.
pistonheadforum said:
roofer - you've not seen my dremel work! Never ends well!
Thanks for tips regarding replacement panels - idealy looking for new if I can get them for a good price (patern parts) as it will need spraying anyway plus the days of hunting round scrappies is something I don't have the time for. Unless you know of any that specialise in BMW parts?
Car was up on the ramp not long ago and no crunching from the rear arches - but a bit to scared to have a proper root around! It's a touring model so not sure if they have the same problems at the rear for rust.
Many thanks,
What colour do you need?Thanks for tips regarding replacement panels - idealy looking for new if I can get them for a good price (patern parts) as it will need spraying anyway plus the days of hunting round scrappies is something I don't have the time for. Unless you know of any that specialise in BMW parts?
Car was up on the ramp not long ago and no crunching from the rear arches - but a bit to scared to have a proper root around! It's a touring model so not sure if they have the same problems at the rear for rust.
Many thanks,
Edited by pistonheadforum on Sunday 2nd October 21:36
User timothy97 on ebay always has a variety of used wings so worth a call to him.
And yes, Tourings rust just as badly as saloons.
Before you spend any money, take the sill covers, rear arch liners and undertrays off and have a good look underneath, especially around the back end of the sills and the area in front of and next to the fuel tank. MOT man can't see these areas as they are covered on the test, so they just sit and fester. I'd put money on most E39's being rotten in those areas by now.
My one was mint all over, perfect arches, rotten floor... thankfully once I'd stripped the exhaust, prop shaft, fuel tank and heat shields off I'm satisfied that the rot is really localised and it was far from a basket case and worth saving. The jacking points were actually all fine!? Nearly sorted now, tiny bit more welding then I've just got to put half the car back together
oh well all good fun
My one was mint all over, perfect arches, rotten floor... thankfully once I'd stripped the exhaust, prop shaft, fuel tank and heat shields off I'm satisfied that the rot is really localised and it was far from a basket case and worth saving. The jacking points were actually all fine!? Nearly sorted now, tiny bit more welding then I've just got to put half the car back together
oh well all good funEdited by lufbramatt on Friday 7th October 10:44
Hi, thanks for advice.
Sounds like replacement wings are out there which is great.
The car is worth half of nothing basically, but I do like it so it might be a good project to fix up.
I do need to pop the inner linings off and have a good root around. I looked at this quickly last night and it appears to be lots of those plastic barb one-time fixings. Almost certainly these will break so I think what I probably need is a bunch of spares or replacements if I am going to strip the car.
Can you buy these plastic barb fixings somewhere aftermarket or is it something generic that can be sourced online?
Many thanks.
Sounds like replacement wings are out there which is great.
The car is worth half of nothing basically, but I do like it so it might be a good project to fix up.
I do need to pop the inner linings off and have a good root around. I looked at this quickly last night and it appears to be lots of those plastic barb one-time fixings. Almost certainly these will break so I think what I probably need is a bunch of spares or replacements if I am going to strip the car.
Can you buy these plastic barb fixings somewhere aftermarket or is it something generic that can be sourced online?
Many thanks.
Gassing Station | BMW General | Top of Page | What's New | My Stuff


