F30 330D front Alloy
Discussion
Pop your chassis no into realoem and also look up your spec on a vin decoder. Vin decoder will give the wheel type on your car, real OEM the part no. Or read the part no if the wheel ( on the back). Or look here: http://www.bmwstylewheels.com/3/F30+
Cheers, the VIN comes back with:
18"M LT/ALY WHEELS STAR SP. 400M/MT
and another one:
BMW LA wheel M Star Spoke 400
I found this website (http://www.wheel-size.com/size/bmw/3-series/2015/#trim-330d-eudm) and the front are 8j and the rears are 8.5j (makes sense as the front tyres are 225/45 and the rears are 255/40). Unfortunately, there are lots of rears on Ebay around the £100 mark but the fronts are over £200 and only a few. Just my luck!
So, I could either keep my eye on Ebay or go to a nearby place which can repair the buckle?
BMW are blaming me for the buckle but in light of the insane amount of time, expense and hassle I've been through with this car's tyres and wheels due to their service department, who are incompetent beyond believe for a premium car brand, they may come back with an offer. Apparently business sales are struggling at the moment. If people knew what their aftercare was like I think that struggle will be permanent. Seriously, they can't even balance wheels properly - it's crazy.
I do have a bit of a dilemma though which I'm still pondering. I'll maybe post it in a new thread.
18"M LT/ALY WHEELS STAR SP. 400M/MT
and another one:
BMW LA wheel M Star Spoke 400
I found this website (http://www.wheel-size.com/size/bmw/3-series/2015/#trim-330d-eudm) and the front are 8j and the rears are 8.5j (makes sense as the front tyres are 225/45 and the rears are 255/40). Unfortunately, there are lots of rears on Ebay around the £100 mark but the fronts are over £200 and only a few. Just my luck!
So, I could either keep my eye on Ebay or go to a nearby place which can repair the buckle?
BMW are blaming me for the buckle but in light of the insane amount of time, expense and hassle I've been through with this car's tyres and wheels due to their service department, who are incompetent beyond believe for a premium car brand, they may come back with an offer. Apparently business sales are struggling at the moment. If people knew what their aftercare was like I think that struggle will be permanent. Seriously, they can't even balance wheels properly - it's crazy.
I do have a bit of a dilemma though which I'm still pondering. I'll maybe post it in a new thread.
Edited by ninjag on Sunday 9th October 23:30
ninjag said:
I found this website (http://www.wheel-size.com/size/bmw/3-series/2015/#trim-330d-eudm) and the front are 8j and the rears are 8.5j (makes sense as the front tyres are 225/45 and the rears are 255/40).
A little bit confused now, I just had my front wheel balanced and the guy looked at my alloy before putting it on the machine and said the fronts were 8.5 and the rears would be 9.5Is this right?
ninjag said:
Mine is buckled and I don't think I'd trust a used one in case it's also buckled, unless I get get a new one on there for cheapness?
I don't trust BMW getting one and fitting because every time I put my car in it comes back worse.
Where are you based? There are some good refurbishers. I don't trust BMW getting one and fitting because every time I put my car in it comes back worse.
ninjag said:
Cheers. It's a brand new wheel but wanted it balanced properly.
It seems smooth enough, I'm not sure if I can feel a hint of vibration though. Would this width mistake make a difference when balancing?
It seems smooth enough, I'm not sure if I can feel a hint of vibration though. Would this width mistake make a difference when balancing?
Depends how it was balanced. If he keyed in the incorrect wheel dimension and used a programme that relied on that, then the wheel wouldn't be balanced, though the remaining imbalance would show when the wheel was check spun.
The dimensions are only input to tell the machine where the weight is going in two axes.
If a shift plane programme was used then the position of the weight is set by using an arm to tell the machine where the weights will be and the dimensions are irrelevant.
The important thing is did the machine read zero after balancing? If it did, assuming correct mounting, the wheel is balanced.
A little mystery solved as to why he was setting to 8.5 on the balancing machine, BMW have put a new rear sized 8.5 alloy on my front axle. The other front Alloy which is the original is 8.0.
Went to ATS this time and looks like I wasn't imagining the vibrations, rebalanced all wheels and it's silky smooth now.
So, is it safe to have an 8.0 width alloy on the front left but an 8.5 on the front right? The tyres are identical.
Went to ATS this time and looks like I wasn't imagining the vibrations, rebalanced all wheels and it's silky smooth now.
So, is it safe to have an 8.0 width alloy on the front left but an 8.5 on the front right? The tyres are identical.
Gassing Station | BMW General | Top of Page | What's New | My Stuff


