Performance tyre repair on shoulder
Performance tyre repair on shoulder
Author
Discussion

rockport

Original Poster:

8 posts

121 months

Friday 7th October 2016
quotequote all
All, I’m looking for opinions on what to do regarding repair.. To set the scene I have just had all x4 MV1 alloys refurbed on my 330 along with x4 brand spanking new 18” Goodyear Eagle F1’s. I kid you not its been less than 2 weeks since fitment when I spotted a screw on the upper outside shoulder of the rear tyre. Pictures below help show my pain.

Its been 10+ years since I’ve sustained a nail or screw puncher of this type, and its sods law this happened days after fitment so im alittle out of touch with todays technology advances.

Some of the bigger named outfits have said the puncher is too close to the wall and can’t be repaired. Chances are if I took to a smaller independent shop I could get the repair done.

Question is… what would you do?

rockport

Original Poster:

8 posts

121 months

Friday 7th October 2016
quotequote all

rockport

Original Poster:

8 posts

121 months

Friday 7th October 2016
quotequote all

Smuler

2,288 posts

170 months

Friday 7th October 2016
quotequote all
Looks very much like where I had one last month on my E46. I took it to a good independent, repaired for I think it was 11£
AT least 1k miles since, no problems.
Only difference, was that offending 'object' had, I presume, fallen out. Don't know if that makes a difference.


Evanivitch

26,533 posts

153 months

Friday 7th October 2016
quotequote all
Are you likely to be driving the car hard once it's repaired?

There's a reason the big names won't fix it, but there's always an element of risk to be balanced.

roofer

5,136 posts

242 months

Friday 7th October 2016
quotequote all
A proper vulcanised repair should sort that.

anonymous-user

85 months

Friday 7th October 2016
quotequote all
roofer said:
A proper vulcanised repair should sort that.

All repairs are vulcanised.

That's no problem at all to repair, assuming there is no external damage from the puncturing object. It requires a reinforced repair as opposed to a simple e rubber patch but all within BS159 and any repairer worth the name should do it.

No need to worry about after repair performance either it would or be fine.

anonymous-user

85 months

Friday 7th October 2016
quotequote all
Evanivitch said:
There's a reason the big names won't fix it.....
You're right, it's easier and more profitable to sell you a new tyre.

Evanivitch

26,533 posts

153 months

Friday 7th October 2016
quotequote all
REALIST123 said:
You're right, it's easier and more profitable to sell you a new tyre.
So they turn away business? That's like saying Autoglass don't repair cracks because it's bad for business.

Engineers have done the tests, risk assessments have been done.

4rephill

5,171 posts

209 months

Saturday 8th October 2016
quotequote all
REALIST123 said:
Evanivitch said:
There's a reason the big names won't fix it.....
You're right, it's easier and more profitable to sell you a new tyre.
The "big names" also tend to stick with the recommendations from the tyre manufacturers about repairs due to liability issues if the repair should fail and be the cause of a major accidents.

The smaller indies don't give a scensoredt!

bmwmike

8,799 posts

139 months

Saturday 8th October 2016
quotequote all
I've got the same thing (large screw) in same place on a RFT and I didn't drive it flat. I asked a local tyre place and they wouldn't repair it.

Can RFT be repaired does anyone know?

buggalugs

9,296 posts

268 months

Sunday 9th October 2016
quotequote all
bmwmike said:
I've got the same thing (large screw) in same place on a RFT and I didn't drive it flat. I asked a local tyre place and they wouldn't repair it.

Can RFT be repaired does anyone know?
I had one done, I felt the screw in it going thunk thunk thunk and pulled into a layby and literally found myself parked behind a mobile tyre fitter having his lunch. He fixed it there and then.

Wills2

29,918 posts

206 months

Sunday 9th October 2016
quotequote all
I think that might be too close to the edge to be repaired, link to an old thread where the BS159 standard is explained 3rd post down.

http://www.pistonheads.com/gassing/topic.asp?h=0&a...


Locknut

653 posts

168 months

Monday 10th October 2016
quotequote all
I would get it repaired if it were mine. Besides all other considerations it is a runflat tyre, so if the repair fails you still have the runflat properties of the tyre and it will perform just like it would with any other cause of deflation.

Vergis

553 posts

273 months

Monday 10th October 2016
quotequote all
Absolutely fine for repair.

Driver101

14,451 posts

152 months

Monday 10th October 2016
quotequote all
There's two threads running on the same subject and by the same person.

http://www.pistonheads.com/gassing/topic.asp?h=0&a...

nickfrog

25,468 posts

248 months

Thursday 13th October 2016
quotequote all
OP. Check if it's within the BS159 repairable area. IE 70% of the width. If it's a 245mm tyre, that's 171.5mm. Measure if the hole is more or less than 86mm from the centre of the tyre. You will also need to know if the hole is greater than 6mm or not as irrespective of location, if it is, then you can't repair it.

TBH, it does indeed look very marginal. http://www.btmauk.com/wp-content/uploads/2014/12/M...