Discussion
Hello all, I'm hoping this will be a fairly boring thread!
I bought a 325ti a few months back. It has lived a fairly hard life in the meantime. It now needs some maintainance. I'll record the work here, any advice is welcome!
Jobs list!
Repair - Aircon not working.
The blower fan stopped working about a month ago. Before that I was getting constant hot air in the footwells regardless of the setting. Also have pixel faults in the control unit display.
Preventative - Engine cooling.
My radiator is bowed at the bottom, so I need a new one. Will also fit new hoses, new thermostat and coolant pump.
Wear - new front brakes
might fit braided lines at the same time.
Wear - gearshift quality improvement
Already tried new gearbox oil. Improvement was only slight. Will remove clutch delay valve. Fit new engine and gearbox mounts, new diff mounts and prop shaft flex joint.
That's probably enough to start with.
I bought a 325ti a few months back. It has lived a fairly hard life in the meantime. It now needs some maintainance. I'll record the work here, any advice is welcome!
Jobs list!
Repair - Aircon not working.
The blower fan stopped working about a month ago. Before that I was getting constant hot air in the footwells regardless of the setting. Also have pixel faults in the control unit display.
Preventative - Engine cooling.
My radiator is bowed at the bottom, so I need a new one. Will also fit new hoses, new thermostat and coolant pump.
Wear - new front brakes
might fit braided lines at the same time.
Wear - gearshift quality improvement
Already tried new gearbox oil. Improvement was only slight. Will remove clutch delay valve. Fit new engine and gearbox mounts, new diff mounts and prop shaft flex joint.
That's probably enough to start with.
Aircon fix up -
So I just bought another cheap control unit on ebay with no pixel issues, part No. 64116916882 for 20 Euro.
Now I think I need to have a go at getting the water valve working again. Realoem is not clear on what valve should be fitted to my car, a simple water valve 64116912454....or do I need the part with the additional water pump?
I might also need either a new Final Stage Unit (64116923204) or maybe my blower has died (64119204154)
So I just bought another cheap control unit on ebay with no pixel issues, part No. 64116916882 for 20 Euro.
Now I think I need to have a go at getting the water valve working again. Realoem is not clear on what valve should be fitted to my car, a simple water valve 64116912454....or do I need the part with the additional water pump?
I might also need either a new Final Stage Unit (64116923204) or maybe my blower has died (64119204154)
helix402 said:
Re cooling system. I recommmed genuine thermos or Mahle/Behr (same thing) and a genuine BMW water pump. They last better.
OK, question for you...people slag off plastic impellers, yet many say to stick with the genuine bmw plastic part.I'd tend to fit the genuine part anyway.
Have fun fitting the heater resistor! They're a complete b
d to replace, another example of where BMW seemingly allowed Renault to re-engineer the simple E36 into a f
king nightmare. Unlike the E36 (passenger side, easy), the E46 resistor is on the drivers side and trapped behind a plastic, easy to break linkage. Inspired!
Nothing wrong with the plastic/nylon impeller pumps - they were an issue 20 years ago but I've replaced a few this/last year that have been 15-20 years old and had just died due to bearing failure. How long are they supposed to last?
I bloody hate the cooling system on these. It replaced the elegant simplicity of the E36 (rad change - 20 minutes tops) with an over complex f
kfest of push fit connectors, brittle plastics and bits that just fail randomly. If you need a new rad, avoid anything other than either genuine BMW or Nissens. Behr Hella ones are garbage as are EIS. I would only use a genuine BMW expansion tank.
d to replace, another example of where BMW seemingly allowed Renault to re-engineer the simple E36 into a f
king nightmare. Unlike the E36 (passenger side, easy), the E46 resistor is on the drivers side and trapped behind a plastic, easy to break linkage. Inspired!Nothing wrong with the plastic/nylon impeller pumps - they were an issue 20 years ago but I've replaced a few this/last year that have been 15-20 years old and had just died due to bearing failure. How long are they supposed to last?
I bloody hate the cooling system on these. It replaced the elegant simplicity of the E36 (rad change - 20 minutes tops) with an over complex f
kfest of push fit connectors, brittle plastics and bits that just fail randomly. If you need a new rad, avoid anything other than either genuine BMW or Nissens. Behr Hella ones are garbage as are EIS. I would only use a genuine BMW expansion tank.It'll be the resistor for the blower that has died. Blowers themselves are pretty robust. I replaced mine at the weekend. Pain of a job to do, but so worth it for heat/cold and not misted up windows! I would recommend the gen BMW one, as aftermarket ones don't last that long. I believe you're in Germany so it's easier to do on a LHD car. My resistor cost £85 from BMW.
ETA: Nope, saw you're in Aus. It is a pain, don't re-fit the top screw on the stepper motor as it'll take ages, piss you off, and is clipped in anyway.
ETA: Nope, saw you're in Aus. It is a pain, don't re-fit the top screw on the stepper motor as it'll take ages, piss you off, and is clipped in anyway.
Edited by JakeT on Tuesday 8th November 15:01
JakeT said:
It'll be the resistor for the blower that has died. Blowers themselves are pretty robust. I replaced mine at the weekend. Pain of a job to do, but so worth it for heat/cold and not misted up windows! I would recommend the gen BMW one, as aftermarket ones don't last that long. I believe you're in Germany so it's easier to do on a LHD car. My resistor cost £85 from BMW.
ETA: Nope, saw you're in Aus. It is a pain, don't re-fit the top screw on the stepper motor as it'll take ages, piss you off, and is clipped in anyway.
I moved to Germany...so it's lhd...lucky me!ETA: Nope, saw you're in Aus. It is a pain, don't re-fit the top screw on the stepper motor as it'll take ages, piss you off, and is clipped in anyway.
Edited by JakeT on Tuesday 8th November 15:01
iSore said:
Have fun fitting the heater resistor! They're a complete b
d to replace, another example of where BMW seemingly allowed Renault to re-engineer the simple E36 into a f
king nightmare. Unlike the E36 (passenger side, easy), the E46 resistor is on the drivers side and trapped behind a plastic, easy to break linkage. Inspired!
Nothing wrong with the plastic/nylon impeller pumps - they were an issue 20 years ago but I've replaced a few this/last year that have been 15-20 years old and had just died due to bearing failure. How long are they supposed to last?
I bloody hate the cooling system on these. It replaced the elegant simplicity of the E36 (rad change - 20 minutes tops) with an over complex f
kfest of push fit connectors, brittle plastics and bits that just fail randomly. If you need a new rad, avoid anything other than either genuine BMW or Nissens. Behr Hella ones are garbage as are EIS. I would only use a genuine BMW expansion tank.
Comparing the bit of work I've done on my E46 with my previous experience of E30 and E36 I have to agree with you.
d to replace, another example of where BMW seemingly allowed Renault to re-engineer the simple E36 into a f
king nightmare. Unlike the E36 (passenger side, easy), the E46 resistor is on the drivers side and trapped behind a plastic, easy to break linkage. Inspired!Nothing wrong with the plastic/nylon impeller pumps - they were an issue 20 years ago but I've replaced a few this/last year that have been 15-20 years old and had just died due to bearing failure. How long are they supposed to last?
I bloody hate the cooling system on these. It replaced the elegant simplicity of the E36 (rad change - 20 minutes tops) with an over complex f
kfest of push fit connectors, brittle plastics and bits that just fail randomly. If you need a new rad, avoid anything other than either genuine BMW or Nissens. Behr Hella ones are garbage as are EIS. I would only use a genuine BMW expansion tank.Thanks for the tips on rad makes!
Kawasicki said:
Ordered the part above....arrived with a "made in China" label...so feeling slightly scammed. I spent 5€ more to order a German made one too...anyway it is installed (easy job, as lhd!), along with a used climate control unit. I now have a perfectly functioning blower and a pixel error free display....so no cold feet commuting tomorrow.I will remove the heater water valve and attempt to free up the valve itself this weekend...that should according to the internet experts, return the function of the footwell temperature control.
Low coolant light came on today during my morning commute. I stopped immediately and had a look to see if there was anything major wrong...nothing untoward found. I couldn't check the coolant level as the engine was hot. I started driving again, keeping an eye on the engine temp...needle didn't budge, and the coolant light went off again, then came on again after 3km and then off again after another 5km. I will check the coolant level now and top up with distilled water.
I think it is time for a new rad (Nissen), expansion tank, hoses, thermostat and water pump.
I think it is time for a new rad (Nissen), expansion tank, hoses, thermostat and water pump.
Gassing Station | BMW General | Top of Page | What's New | My Stuff


