ABS/DSC Faults
Discussion
I have the following fault codes:
Speed Sensor Front Right 005DA3
Speed Sensor Front Left 005D93
Speed Signal Missing 0093FB
I have also heard a hissing noise from under the bonnet akin to a vacuum leak.
I went around the engine bay yesterday with some brake cleaner but could not locate the leak.
I am guessing the front sensors are whacked... but that does not explain the missing speed signal.
Hopefully it is not the dreaded DSC hydro pump unit thing majiggy...
Any thoughts welcome :-)
Speed Sensor Front Right 005DA3
Speed Sensor Front Left 005D93
Speed Signal Missing 0093FB
I have also heard a hissing noise from under the bonnet akin to a vacuum leak.
I went around the engine bay yesterday with some brake cleaner but could not locate the leak.
I am guessing the front sensors are whacked... but that does not explain the missing speed signal.
Hopefully it is not the dreaded DSC hydro pump unit thing majiggy...
Any thoughts welcome :-)
My reply will be based on if you work on the car.
Before doing anything I'd get a crow bar and check the front bushes and balljoints for play as that could throw out the sensors. Also, are your tyre sizes correct all round?
Depending on how much the sensors are I'd be tempted to buy a sensor and then recheck the codes. If they don't change you know the sensors are not at fault.
Corroded connection somewhere maybe? Does your speedo work? Do you have access to live data? If you are about in Warwickshire I may be able to help with the live data part.
Before doing anything I'd get a crow bar and check the front bushes and balljoints for play as that could throw out the sensors. Also, are your tyre sizes correct all round?
Depending on how much the sensors are I'd be tempted to buy a sensor and then recheck the codes. If they don't change you know the sensors are not at fault.
Corroded connection somewhere maybe? Does your speedo work? Do you have access to live data? If you are about in Warwickshire I may be able to help with the live data part.
Edited by SebringMan on Tuesday 20th December 14:13
First off, how good is the battery? Low voltage & cold weather gave me false readings for a couple of months on my old e92, without ever affecting the starting capability. Worth a quick check from the 'hidden' menu in the dash.
Then, when you were under the bonnet, did you take off the covers (drivers side, from slam panel) so you could see the brake servo? The hydro unit sits there, so any leaks wouldn't be visible without removing the covers first.
From my experience, this is only getting more common on the e9x models, and it's usually showing around winter - I do wonder whether lower temperatures & therefore a bit more slip than usual exacerbates the issue? I have no proof whatsoever, it's just this seems more common in winter!
Finally, if you can do without the car for approx. 1 week, ECUTuning (I think i've got that right - & no affiliation) in Leics. will sort it for you - they're without doubt the place to go for this repair.
Then, when you were under the bonnet, did you take off the covers (drivers side, from slam panel) so you could see the brake servo? The hydro unit sits there, so any leaks wouldn't be visible without removing the covers first.
From my experience, this is only getting more common on the e9x models, and it's usually showing around winter - I do wonder whether lower temperatures & therefore a bit more slip than usual exacerbates the issue? I have no proof whatsoever, it's just this seems more common in winter!
Finally, if you can do without the car for approx. 1 week, ECUTuning (I think i've got that right - & no affiliation) in Leics. will sort it for you - they're without doubt the place to go for this repair.
Really appreciate the response and ideas.
I will check it out tomorrow with a crow bar / remove the cover where the unit lives.
The hidden menu shows 12.1v as resting voltage and 14.7v when running. I use a CTEK battery tender fortnightly.
Will keep ECU testing in mind. They repaired my mechatronic unit on my Audi S3 (S-Tronic) many moons ago.
Updated with voltage
I will check it out tomorrow with a crow bar / remove the cover where the unit lives.
The hidden menu shows 12.1v as resting voltage and 14.7v when running. I use a CTEK battery tender fortnightly.
Will keep ECU testing in mind. They repaired my mechatronic unit on my Audi S3 (S-Tronic) many moons ago.
Updated with voltage
Edited by Super_G on Wednesday 21st December 20:02
Gassing Station | BMW General | Top of Page | What's New | My Stuff





