The 1 penny split pin that could save your life
The 1 penny split pin that could save your life
Author
Discussion

devs

Original Poster:

33 posts

166 months

Saturday 11th February 2017
quotequote all
I purchased a bike a little while back which had been damaged in an accident. The accident occured as the bike was missing a single split pin, worth about 1 penny.

It's the split pin that holds the rear brake plate to the stay, which then attaches to the body. See images below!






This split pin was missing, which meant that overtime, the nut worked its way loose. Once the nut fell off, the brake stay worked it's way off the bolt and then, when the rider applied his rear brake - this happened to the brake rod.




Basically, when the rear brake was applied, the brake plate rotated with the wheel as it was no longer attached to the brake stay. This pulled the brake rod away from the brake lever and it wrapped itself around the rear wheel, which then locked up.



When the brake rod pulled away from the brake lever, the hanger destroyed itself and the exhaust also suffered damage as it attaches to the rear of the hanger. The brake lever also died a sudden death.

The was at around 20mph. Locking up a rear wheel at 70mph+ ........ scary st!

Just a wake up call to anyone that doesn't think these split pins are important.

Be safe people!

tezzer

984 posts

217 months

Saturday 11th February 2017
quotequote all
Its in the wrong way, the closed end should be at the front.

If any road debris knocks it from the front, it can push the R clip out.

Simple, but often overlooked point.

Edited by tezzer on Saturday 11th February 16:01

devs

Original Poster:

33 posts

166 months

Saturday 11th February 2017
quotequote all
Thanks Tezzer. I'll change mine now to avoid the same mishap!

CoolHands

23,736 posts

226 months

Saturday 11th February 2017
quotequote all
Let me guess. It's Chinese.

devs

Original Poster:

33 posts

166 months

Saturday 11th February 2017
quotequote all
Kawasaki ER500. Standard bread and butter winter hacks.

Mr2Mike

20,143 posts

286 months

Saturday 11th February 2017
quotequote all
devs said:
This split pin was missing, which meant that overtime, the nut worked its way loose. Once the nut fell off, the brake stay worked it's way off the bolt and then, when the rider applied his rear brake - this happened to the brake rod.
Not quite true. The split pin prevents the nut falling off completely if it does loosen, but it does not prevent the nut loosening. Nuts should not loosen anyway if torqued correctly.

Biker's Nemesis

41,489 posts

239 months

Saturday 11th February 2017
quotequote all
That happened to me on my fizzy in 1982.
You could also fit a nylock nut.

bimsb6

8,812 posts

252 months

Saturday 11th February 2017
quotequote all
Biker's Nemesis said:
That happened to me on my fizzy in 1982.
You could also fit a nylock nut.
That would be the way to go .

Pothole

34,367 posts

313 months

Saturday 11th February 2017
quotequote all
Neither of my Triumphs appears to have this Heath Robinson arrangement.

dc2rr07

1,238 posts

262 months

Saturday 11th February 2017
quotequote all
tezzer said:
Its in the wrong way, the closed end should be at the front.

If any road debris knocks it from the front, it can push the R clip out.

Simple, but often overlooked point.

Edited by tezzer on Saturday 11th February 16:01
Glad to see someone using the correct nomenclature and as stated it is in the wrong way.

muddyfox

30 posts

192 months

Saturday 11th February 2017
quotequote all
That's an R clip and no matter what way it's fitted it can easily be knocked out.
A correctly fitted split pin would be a much better and safer option.

twizellb

2,786 posts

243 months

Saturday 11th February 2017
quotequote all
Biker's Nemesis said:
That happened to me on my fizzy in 1982.
You could also fit a nylock nut.
John can you remember my brand new zx10 in 2004? first day out with Mcgill on the cambo road, the rear caliper came adrift and was mashing the back wheeleek

Tango13

10,203 posts

207 months

Saturday 11th February 2017
quotequote all
Always Nyloc and if in doubt lockwire.

leighz

473 posts

163 months

Saturday 11th February 2017
quotequote all
I sympathise but at least you didn't lose a leg

these sort of components are all over a bike if you think about it

Rubin215

4,202 posts

187 months

Saturday 11th February 2017
quotequote all
Tango13 said:
Always Nyloc and if in doubt lockwire.
And weld it too, just to be sure.

CoolHands

23,736 posts

226 months

Saturday 11th February 2017
quotequote all
I had a chain snap once. I wouldn't worry about it.

Tango13

10,203 posts

207 months

Saturday 11th February 2017
quotequote all
Rubin215 said:
Tango13 said:
Always Nyloc and if in doubt lockwire.
And weld it too, just to be sure.
yes Duct tape on top of the welds too

Biker's Nemesis

41,489 posts

239 months

Saturday 11th February 2017
quotequote all
twizellb said:
John can you remember my brand new zx10 in 2004? first day out with Mcgill on the cambo road, the rear caliper came adrift and was mashing the back wheeleek
I do William, you were a lucky boy that day.

srob

12,567 posts

269 months

Saturday 11th February 2017
quotequote all
Tango13 said:
Rubin215 said:
Tango13 said:
Always Nyloc and if in doubt lockwire.
And weld it too, just to be sure.
yes Duct tape on top of the welds too
And peen the end over. Can't be too careful.

Biker's Nemesis

41,489 posts

239 months

Saturday 11th February 2017
quotequote all
I lock wire the R clips on the race bikes (moto x) callipers.