Electrical muppetry
Discussion
I have had an electrical problem with my 125 since last year and with me being a man I steadfastly ignored it until a few weeks back. If you had the lights on the indicators would not work, if you turned the lights off the temperature gauge would stop working. The horn wouldn't work whatever you did...
...So, a couple of weeks ago after messing around with it for a full day I took the fairing and headlight off so I could get to all the wiring but still could not get anything to work as it should.
After having a right old spanner throwing session and swearing, kicking and punching things in the garage until the veins in my neck were bulging I rang a mate who's the head Yamaha mechanic at the local dealers.
he turned up last night with his tester and within 5 minutes had found the fault....John he says, its the fuse!
Well f
k me with a wire brush I says, I've checked that half a dozen times, turns out it looks fine and dandy but the wire must be broken behind the metal cap. (its the old style glass fuse)
I'm out tonight with him and a load of others so I'll be getting stick all evening for being a knacker.
This thread is punishment for wasting peoples times.
I feel better for confessing.
P.S.
As R1 Loon would always say...(check the fuses)
...So, a couple of weeks ago after messing around with it for a full day I took the fairing and headlight off so I could get to all the wiring but still could not get anything to work as it should.
After having a right old spanner throwing session and swearing, kicking and punching things in the garage until the veins in my neck were bulging I rang a mate who's the head Yamaha mechanic at the local dealers.
he turned up last night with his tester and within 5 minutes had found the fault....John he says, its the fuse!
Well f
k me with a wire brush I says, I've checked that half a dozen times, turns out it looks fine and dandy but the wire must be broken behind the metal cap. (its the old style glass fuse)I'm out tonight with him and a load of others so I'll be getting stick all evening for being a knacker.
This thread is punishment for wasting peoples times.
I feel better for confessing.
P.S.
As R1 Loon would always say...(check the fuses)
Biker's Nemesis said:
I have had an electrical problem with my 125 since last year and with me being a man I steadfastly ignored it until a few weeks back. If you had the lights on the indicators would not work, if you turned the lights off the temperature gauge would stop working. The horn wouldn't work whatever you did...
...So, a couple of weeks ago after messing around with it for a full day I took the fairing and headlight off so I could get to all the wiring but still could not get anything to work as it should.
After having a right old spanner throwing session and swearing, kicking and punching things in the garage until the veins in my neck were bulging I rang a mate who's the head Yamaha mechanic at the local dealers.
he turned up last night with his tester and within 5 minutes had found the fault....John he says, its the fuse!
Well f
k me with a wire brush I says, I've checked that half a dozen times, turns out it looks fine and dandy but the wire must be broken behind the metal cap. (its the old style glass fuse)
I'm out tonight with him and a load of others so I'll be getting stick all evening for being a knacker.
This thread is punishment for wasting peoples times.
I feel better for confessing.
P.S.
As R1 Loon would always say...(check the fuses)
for me, internet statement of the day. i'm crying here....So, a couple of weeks ago after messing around with it for a full day I took the fairing and headlight off so I could get to all the wiring but still could not get anything to work as it should.
After having a right old spanner throwing session and swearing, kicking and punching things in the garage until the veins in my neck were bulging I rang a mate who's the head Yamaha mechanic at the local dealers.
he turned up last night with his tester and within 5 minutes had found the fault....John he says, its the fuse!
Well f
k me with a wire brush I says, I've checked that half a dozen times, turns out it looks fine and dandy but the wire must be broken behind the metal cap. (its the old style glass fuse)I'm out tonight with him and a load of others so I'll be getting stick all evening for being a knacker.
This thread is punishment for wasting peoples times.
I feel better for confessing.
P.S.
As R1 Loon would always say...(check the fuses)
thank you for your bike confession..infact, maybe we should have a bike confession thread

My confession:
Triumph Speed Four. Put new adjustable levers on. Adjusted and bled brakes. Adjusted clutch. Didn't notice that clutch cable has snagged somewhere.
Rode up the garden, all good. Turned around. Started releasing the clutch to ride back down the garden... clutch cable unsnagged and dumped the clutch in first gear. Bike heads skywards and over to the side and I go off the back. Bike comes down on my thigh.
Bruised, but the bike was ok. Just a scuffed engine slider and bar end, and a snapped new brake lever. F**K.
Triumph Speed Four. Put new adjustable levers on. Adjusted and bled brakes. Adjusted clutch. Didn't notice that clutch cable has snagged somewhere.
Rode up the garden, all good. Turned around. Started releasing the clutch to ride back down the garden... clutch cable unsnagged and dumped the clutch in first gear. Bike heads skywards and over to the side and I go off the back. Bike comes down on my thigh.
Bruised, but the bike was ok. Just a scuffed engine slider and bar end, and a snapped new brake lever. F**K.
spookly said:
My confession:
Triumph Speed Four. Put new adjustable levers on. Adjusted and bled brakes. Adjusted clutch. Didn't notice that clutch cable has snagged somewhere.
Rode up the garden, all good. Turned around. Started releasing the clutch to ride back down the garden... clutch cable unsnagged and dumped the clutch in first gear. Bike heads skywards and over to the side and I go off the back. Bike comes down on my thigh.
Bruised, but the bike was ok. Just a scuffed engine slider and bar end, and a snapped new brake lever. F**K.
noooo I'm crying again.....Triumph Speed Four. Put new adjustable levers on. Adjusted and bled brakes. Adjusted clutch. Didn't notice that clutch cable has snagged somewhere.
Rode up the garden, all good. Turned around. Started releasing the clutch to ride back down the garden... clutch cable unsnagged and dumped the clutch in first gear. Bike heads skywards and over to the side and I go off the back. Bike comes down on my thigh.
Bruised, but the bike was ok. Just a scuffed engine slider and bar end, and a snapped new brake lever. F**K.
cmon, shall we see if a bike confession thread goes for it? there must be loads of stories out there that can't be lost :0
Years ago, I had a lovely FJ1200. I wheeled it out of the garage one morning, intending to fit new front and rear pads, a nice and easy job, even for me. Our drive has quite a slope down to the road....can you see where this, or more specifically where the FJ, is heading?
Anyways, old pads out, pistons pushed in to accomodate chunky new ones. Into the house to don suitable attire, then leap astride my pride and joy, safe in the knowledge that its brakes will now be fantastic. I start to back-pedal down the drive....speed increases....gently apply front brake prior to interacting with any passing traffic....lever comes back to the bars, speed increases scarily as my brain tries desperately to process what the f**** is going on, I shoot across the road backwards, for some reason turn the bars slightly to the left....and the FJ flops spectacularly onto its side just as we collide with the neighbour's brand new Punto parked opposite.
Kin ell.
Pete
Anyways, old pads out, pistons pushed in to accomodate chunky new ones. Into the house to don suitable attire, then leap astride my pride and joy, safe in the knowledge that its brakes will now be fantastic. I start to back-pedal down the drive....speed increases....gently apply front brake prior to interacting with any passing traffic....lever comes back to the bars, speed increases scarily as my brain tries desperately to process what the f**** is going on, I shoot across the road backwards, for some reason turn the bars slightly to the left....and the FJ flops spectacularly onto its side just as we collide with the neighbour's brand new Punto parked opposite.
Kin ell.
Pete
I'll admit to a pretty silly one. I replaced the fuel pump on the blade last year. I'd drained the tank and took it off to gain access took the old pump off and cleaned everything the fitted the new pump. reattached all of the wiring and then all of the fuel lines. Put everything back and turned on the ignition whir went the pump as it primed. "aha" I thought fixed !
I thumbed the starter and brum she fires up then seconds later cuts out, and now the motor spins but it won't start ? I take everything off and check it again, then I put it back and it still won't start.
I'm just blaming everything and everybody including Jesus H Christ when the misses brings me a brew and says I'll just put it here. Right next to the fuel can with the fuel in it I'd drained ! Needles to say once I'd put it back in the tank all was good
I thumbed the starter and brum she fires up then seconds later cuts out, and now the motor spins but it won't start ? I take everything off and check it again, then I put it back and it still won't start.
I'm just blaming everything and everybody including Jesus H Christ when the misses brings me a brew and says I'll just put it here. Right next to the fuel can with the fuel in it I'd drained ! Needles to say once I'd put it back in the tank all was good

Few years ago I was replacing the air filter and tensioning the throttle cable amongst other routine jobs on my RSV.. anyway think I've all finished so go for a quick run up the road to check all is well.
Bike ticks over ok but wont move more than a yard or two without cutting out. This goes on intermittently for a few attempts until suddenly the throttle gets stuck wide open and the bike tries to make a new doorway in the brickwall of the garage. Cue swearing at italian electrical trickery and rage at why i didnt take it to a garage and let someone else do the work.
After a fag and a rethink, lifted the tank to check what was going on.. turns out I'd left the rags wedged in the throttle bodies. Muppet
Bike ticks over ok but wont move more than a yard or two without cutting out. This goes on intermittently for a few attempts until suddenly the throttle gets stuck wide open and the bike tries to make a new doorway in the brickwall of the garage. Cue swearing at italian electrical trickery and rage at why i didnt take it to a garage and let someone else do the work.
After a fag and a rethink, lifted the tank to check what was going on.. turns out I'd left the rags wedged in the throttle bodies. Muppet
Mine isn't too bad, but still annoying.
I wheeled my ZX7R out of the garage onto the drive. There is a drop onto the drive but it is tiny, like 15-20mm but evidently enough to catch the stand on getting it out of the garage. I was on the right hand side of the bike and the side stand was down. So I wheeled it out and went to lean it onto is stand, cue the bike falling straight over and me following it. I'm not small at 6ft4 and 14.5 stone but trying to hold 200+kg of ZX7R up with one hand on the grip when you're not expecting it is going to happen! I managed to lay it down fairly gently but it still cracked a fairing and scuffed some bits. Surprisingly easy to pick up though.
The next week I took it for an MOT and needed it roll it forward in the space it was in, cue exactly the same thing happening again! With people watching it's not so easy to pick such a tank up off the floor but I still managed. Luckily no more damage done.
Since then I haven't dropped a bike, sods law now I've said that I will!
I wheeled my ZX7R out of the garage onto the drive. There is a drop onto the drive but it is tiny, like 15-20mm but evidently enough to catch the stand on getting it out of the garage. I was on the right hand side of the bike and the side stand was down. So I wheeled it out and went to lean it onto is stand, cue the bike falling straight over and me following it. I'm not small at 6ft4 and 14.5 stone but trying to hold 200+kg of ZX7R up with one hand on the grip when you're not expecting it is going to happen! I managed to lay it down fairly gently but it still cracked a fairing and scuffed some bits. Surprisingly easy to pick up though.
The next week I took it for an MOT and needed it roll it forward in the space it was in, cue exactly the same thing happening again! With people watching it's not so easy to pick such a tank up off the floor but I still managed. Luckily no more damage done.
Since then I haven't dropped a bike, sods law now I've said that I will!
Edited by patchb on Friday 10th March 21:51
Oh actually I have another one. When I was 15 I bought a Nastro Azzuro liveried Aprilia RS50. I spent the couple of months prepping the bodywork and had it painted in the lovely metallic blue that B2H ZX6R's came in so that it matched my old mans B2H. Passed my CBT and went and picked it up from my old mans workshop. I stopped half a mile down the road to get some fuel, and somehow I managed to knock it off its stand, scuffing the freshly painted fairings and new double bubble screen that I had fitted.
It seems that most of my mishaps are sidestand related....
Edit: And yet another one! I bought myself a mint 2003 Tuono 125 just before I was 17. I was in the garage tinkering with my RS50 and somehow it fell over, on picking it back up I was a bit too vigorous and knocked my 125 over, narrowly missing my brothers ZX6R. Luckily no damage done that time!
I think I've got better in my maneuvering of stationary bikes since then!
It seems that most of my mishaps are sidestand related....
Edit: And yet another one! I bought myself a mint 2003 Tuono 125 just before I was 17. I was in the garage tinkering with my RS50 and somehow it fell over, on picking it back up I was a bit too vigorous and knocked my 125 over, narrowly missing my brothers ZX6R. Luckily no damage done that time!
I think I've got better in my maneuvering of stationary bikes since then!
Edited by patchb on Friday 10th March 21:50
Biker's Nemesis said:
I have had an electrical problem with my 125 since last year and with me being a man I steadfastly ignored it until a few weeks back. If you had the lights on the indicators would not work, if you turned the lights off the temperature gauge would stop working. The horn wouldn't work whatever you did...
...So, a couple of weeks ago after messing around with it for a full day I took the fairing and headlight off so I could get to all the wiring but still could not get anything to work as it should.
After having a right old spanner throwing session and swearing, kicking and punching things in the garage until the veins in my neck were bulging I rang a mate who's the head Yamaha mechanic at the local dealers.
he turned up last night with his tester and within 5 minutes had found the fault....John he says, its the fuse!
Well f
k me with a wire brush I says, I've checked that half a dozen times, turns out it looks fine and dandy but the wire must be broken behind the metal cap. (its the old style glass fuse)
I'm out tonight with him and a load of others so I'll be getting stick all evening for being a knacker.
This thread is punishment for wasting peoples times.
I feel better for confessing.
P.S.
As R1 Loon would always say...(check the fuses)
I have to admit I've done the same thing myself. Lesson learnt I wont be doing that ever again. ...So, a couple of weeks ago after messing around with it for a full day I took the fairing and headlight off so I could get to all the wiring but still could not get anything to work as it should.
After having a right old spanner throwing session and swearing, kicking and punching things in the garage until the veins in my neck were bulging I rang a mate who's the head Yamaha mechanic at the local dealers.
he turned up last night with his tester and within 5 minutes had found the fault....John he says, its the fuse!
Well f
k me with a wire brush I says, I've checked that half a dozen times, turns out it looks fine and dandy but the wire must be broken behind the metal cap. (its the old style glass fuse)I'm out tonight with him and a load of others so I'll be getting stick all evening for being a knacker.
This thread is punishment for wasting peoples times.
I feel better for confessing.
P.S.
As R1 Loon would always say...(check the fuses)
I once had the luxury of choosing between three local bike dealers for parts: one a mile away, one 10 miles away and one 15 miles away.
One day I needed some brake pads for my 550 Kat; rang around and found that the furthest place had the cheapest pads (by literally a pound or two).
So I jumped in the car and set off. Trying to out-drag a Volvo round a roundabout I lost the back end, bounced off the kerb and found the car would no longer drive.
A quick examination showed I'd put a 30 degree bend in one of the half-shafts.
Cost me £50 to have the car recovered, £30 to fix it and I still had to buy bloody brake pads for the bike...
One day I needed some brake pads for my 550 Kat; rang around and found that the furthest place had the cheapest pads (by literally a pound or two).
So I jumped in the car and set off. Trying to out-drag a Volvo round a roundabout I lost the back end, bounced off the kerb and found the car would no longer drive.
A quick examination showed I'd put a 30 degree bend in one of the half-shafts.
Cost me £50 to have the car recovered, £30 to fix it and I still had to buy bloody brake pads for the bike...
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff





