Dymag Carbon Wheels
Author
Discussion

StuB

Original Poster:

6,695 posts

270 months

Tuesday 14th March 2017
quotequote all
Rather than sell my beloved K5, I'm toying with the idea of carbon wheels as an upgrade.

Any reasons why I shouldn't?? I think I've read enough positives & see that they seem to hold value ok also.

Edited by StuB on Tuesday 14th March 22:14

curlie467

7,650 posts

232 months

Tuesday 14th March 2017
quotequote all
Nope, no reasons whatsoever. My mate has them on his CBR, they're lovely!

998420

929 posts

182 months

Tuesday 14th March 2017
quotequote all
Are BST not the pioneers and the best bet for carbon wheels ?

I always fancied a pair, just never got round to robbing a bank

308mate

13,758 posts

253 months

Tuesday 14th March 2017
quotequote all
Personally I think a nice set of Marchesinis look loads better. But I'm not in the market so I'll shut up. biggrin

mckeann

2,996 posts

260 months

Tuesday 14th March 2017
quotequote all
I know of a couple of quick lads who struggled with suspension and handling after losing so much unsprung weight. It's bound to make a big difference. It made me wonder if the folk who rave about it making a huge difference are the ones who are miles away from the limit of the bike already, so you might want to be wary as you're obviously a fast lad, and can ride a bike to its limits.

This is assuming it's a track bike, if it's a road bike then I doubt anyone short of Mcguiness will push hard enough to run into bike limits on the road

StuB

Original Poster:

6,695 posts

270 months

Tuesday 14th March 2017
quotequote all
mckeann said:
I know of a couple of quick lads who struggled with suspension and handling after losing so much unsprung weight. It's bound to make a big difference. It made me wonder if the folk who rave about it making a huge difference are the ones who are miles away from the limit of the bike already, so you might want to be wary as you're obviously a fast lad, and can ride a bike to its limits.

This is assuming it's a track bike, if it's a road bike then I doubt anyone short of Mcguiness will push hard enough to run into bike limits on the road
It's my road bike. Hopefully what I learned about suspension set up will still apply.

As below, it's quite a significant upgrade on a road bike, but I subscribe to the mantra of lightness as a fundamental principle of performance.

Who are the experts in changes? Looking at getting them from Tony at Motodex. They e run at BSB level, so hopefully quite a useful resource.

308mate

13,758 posts

253 months

Tuesday 14th March 2017
quotequote all
I reckon it's one of the best changes you can make to a bike. Even if you're not McGuiness, you're going to instantly notice the difference in gyroscopic forces. Makes a bike feel like Fred Astaire on wheels

Farlig

633 posts

183 months

Tuesday 14th March 2017
quotequote all
I can only comment that the first time I went from std oem to mag wheels I was fkn astounded at the change. The bike instantly felt more responsive and tipped into corners so suddenly I thought there was something wrong until I recalibrated my brain!! The move to CF can only be the same. But, as mentioned above, such a massive change to unsprung weight will affect the suspension behaviour effectively stiffening it up... I´m no riding god, only an engineer, so can´t say more than that 2p...

graeme4130

3,956 posts

212 months

Tuesday 14th March 2017
quotequote all
I run BST carbon wheels on my ZX10R
Besides the obvious weight saving benefits to acceleration, there's the added bonus of unsprung weight helping the wheels track less than perfect surfaces (most roads and bits of some tracks), to help grip levels, and the improvement how quickly you can get the bike over with the reduced gyroscopic weight makes a massive difference
I've run my bike back to back on days with my spare standard wheels (admittedly, very heavy on a ZX10R) and it feels like trying to tip in a cruise liner in comparison
I understand lighter wheels make for a better tyre life too

On the negatives though :
They're very expensive
You're very conscious of who changes your tyres
If you smack them, you won't know if they're damaged unless you X-ray them

My bike has the front already when I got it, and I've got a good mate who works in carbon for an F1 team, so I got him to take into work and check it. He says it was some of the best quality carbon layup he'd seen

However, if I was buying again, I'd probably go for one of the other lightweight forged alloy wheels just because of he constant worry of damaging them during tyre changes, which for me is circa 20-30 times a years
They look bloody cool though

MattOz

4,021 posts

295 months

Tuesday 14th March 2017
quotequote all
Do love the look of carbon wheels. I run Marchesinis on my K7 and they've been excellent for the last 7 years.


Biker's Nemesis

41,487 posts

239 months

Wednesday 15th March 2017
quotequote all
Forged Dymags on my Fireblade seemed too make the bike flip from side to side easier. Pity I couldn't fit on the damn thing.

Mr OCD

6,388 posts

242 months

Wednesday 15th March 2017
quotequote all
Biker's Nemesis said:
Forged Dymags on my Fireblade seemed too make the bike flip from side to side easier. Pity I couldn't fit on the damn thing.
Still not bitter much are you. wink

I'd have carbon rims for the Fireblade in a heart beat if I had £3500 to throw at the bike biggrin

Renn Sport

2,761 posts

240 months

Wednesday 15th March 2017
quotequote all
graeme4130 said:
I run BST carbon wheels on my ZX10R
Besides the obvious weight saving benefits to acceleration, there's the added bonus of unsprung weight helping the wheels track less than perfect surfaces (most roads and bits of some tracks), to help grip levels, and the improvement how quickly you can get the bike over with the reduced gyroscopic weight makes a massive difference
I've run my bike back to back on days with my spare standard wheels (admittedly, very heavy on a ZX10R) and it feels like trying to tip in a cruise liner in comparison
I understand lighter wheels make for a better tyre life too

On the negatives though :
They're very expensive
You're very conscious of who changes your tyres
If you smack them, you won't know if they're damaged unless you X-ray them

My bike has the front already when I got it, and I've got a good mate who works in carbon for an F1 team, so I got him to take into work and check it. He says it was some of the best quality carbon layup he'd seen

However, if I was buying again, I'd probably go for one of the other lightweight forged alloy wheels just because of he constant worry of damaging them during tyre changes, which for me is circa 20-30 times a years
They look bloody cool though
Those wheels look awesome.

I would love some Carbon wheels but I am not sure if I could take the worry of a cracked wheel.

I think I would plump for some OZ Wheels in blinging gold.

Steve Bass

10,760 posts

264 months

Wednesday 15th March 2017
quotequote all
To get a better idea....

http://www.brocksperformance.com/brocknm/templates...

Truth is there's very little in it regarding CF wheels.
Yes, tyre changes are a point of attention but who lets a Halfrauds monkey change their tyres anyway??? They require no special process just proper use of the correct tools.
Personally I've always gone for BST but as they're 5kms from my front door, i'd be silly not to. But the difference they make is remarkable, especially when compared to older bikes wheels.
Suspension will need to significantly slowed down as the moment of inertia is so low and the suspension needs much less force to control them.

graeme4130

3,956 posts

212 months

Wednesday 15th March 2017
quotequote all
Steve Bass said:
To get a better idea....

http://www.brocksperformance.com/brocknm/templates...

Truth is there's very little in it regarding CF wheels.
Yes, tyre changes are a point of attention but who lets a Halfrauds monkey change their tyres anyway??? They require no special process just proper use of the correct tools.
Personally I've always gone for BST but as they're 5kms from my front door, i'd be silly not to. But the difference they make is remarkable, especially when compared to older bikes wheels.
Suspension will need to significantly slowed down as the moment of inertia is so low and the suspension needs much less force to control them.
That test makes for some interesting reading