Suzuki SV650 2017 - Lowering
Suzuki SV650 2017 - Lowering
Author
Discussion

Carmo99

Original Poster:

1,308 posts

217 months

Friday 14th April 2017
quotequote all
My other half sat on one yesterday and it's much lower than the previous model (785mm now) and is a lovely looking bike. She's v short so would still need it lowered another 2 to 3" to be comfortable (on tip, tip toes). She prefers sports bikes to custom bikes but is stuck here due to their lower seat heights (680mm +\-).

Anyone had any experiences, either seat mods, suspension lowering kits or.....?
Thanks
Chris

Jazoli

9,707 posts

281 months

Friday 14th April 2017
quotequote all
You can lower a bike by 2-3" but where is your ground clearance going to be? you'll be decking the pegs out at moderate lean angles, lowering kits work and usually just consist of longer dog bones in the rear linkage, combined with raising the forks in the yoke, but you are altering the geometry by doing this and the bike may end up very unstable as you a shortening the steering angle considerably.

Best bet is a modified seat and platform boots!

Carmo99

Original Poster:

1,308 posts

217 months

Friday 14th April 2017
quotequote all
Agreed on all points but she's not a fast rider so ground clearance is not the main issue. I'd be more concerned if the handling would be b*ggered.
As she's small and light(<60kg) I know one can play with the suspension damping / rebound etc.
I'm talking with the main dealer next week who has some ideas to discuss. (Seat / suspension and some mods)


King Herald

23,501 posts

247 months

Friday 14th April 2017
quotequote all
Lowering a bike also lowers its centre of gravity, so you don't need to lean it as far in corners. To a degree.

It also means side and centre stands need modifying too. Bear in mind your warranty might not be too valid if you make a bunch of changes to the bike, you know how they get when you want something fixed....

A cut down seat or custom seat might be the easiest way to get her feet on the ground.

I fitted a lowering kit to my Bandit 1200 and the seat height dropped best part of 1 1/2"

Side stand is still usable, just. Centre stand takes some muscle to get it up and on.

Moulder

1,648 posts

243 months

Friday 14th April 2017
quotequote all
If she prefers sportsbikes would something like a ZXR400 or KTM390 be a possibility?

Lighter, narrower seat, and not much performance difference to the SV.

LuS1fer

43,570 posts

276 months

Friday 14th April 2017
quotequote all
Shame that Honda don't make the MSX in a bigger capacity.

MikeA3

305 posts

228 months

Friday 14th April 2017
quotequote all
As someone's mentioned above, if she prefers the look of a sportsbike then a 400 would fit the bill nicely as they all have low seat heights.

Might be tricky getting a good one these days but certainly worth a look

Giby

105 posts

193 months

Friday 14th April 2017
quotequote all
shame she doesn't want a sportsbike. I have a custom Ohlins rear shock that was made by MCT in Stowmarket to lower my wife's old R6 (side exshaust model). The bike was lowered by over 3'' and by dropping the forks the bike was tiny but importantly it still handled really well.

Carmo99

Original Poster:

1,308 posts

217 months

Saturday 15th April 2017
quotequote all
Thanks Giby, this is the sort of info we want.

She also looked at the new Honda CA500 (Rebel) and Yamaha SV(?) 950 and both were perfect with low seats and importantly she could reach the foot controls but she prefers the naked sport bike look. I saw this link www.metisse.de which is interesting.

Mr2Mike

20,143 posts

286 months

Saturday 15th April 2017
quotequote all
King Herald said:
Lowering a bike also lowers its centre of gravity, so you don't need to lean it as far in corners. To a degree.
COG makes negligible difference to lean angle in practical termS. At the extremes a bike with a higher COG will actually lean slightly less than a bike with a lower COG, the difference being dependent on the width of the tyres (wider tyres=more lean required).