Brembo RCS 19 Master Cylinder
Brembo RCS 19 Master Cylinder
Author
Discussion

Wildfire

Original Poster:

9,951 posts

283 months

Tuesday 18th April 2017
quotequote all
After getting back on the sports bike after taking winter off, I have found that the brakes aren't quite up to spec compared to the brakes on the commuter.

The sports bike is an '13 plate MV F3 675 (non-ABS) with gold Brembo pads and the commuter is a 16 plate Ducati Monster 821 with Mono-blocs and ABS.

I find the Ducati maybe has a bit too much initial bite, but there seems to be much more power. Could this be to do with the ABS pump?

Anyhow I have been toying with the idea of upgrading my MC to a Brembo RCS.

Is it worth it? Is there anything I need to think about first?

Wildfire

Original Poster:

9,951 posts

283 months

Tuesday 18th April 2017
quotequote all
No one at all..

R1 Dave

7,158 posts

294 months

Tuesday 18th April 2017
quotequote all
All the reviews I've read have been excellent and I plan to put one on my R1 when I get round to ordering one.

Steve Bass

10,758 posts

264 months

Wednesday 19th April 2017
quotequote all
Guys,

Before you buy the 19 do the calculations to make sure it's the right size for your particular system.
Choosing the wrong pump will either give wooden brakes (Yamahas!! biggrin) or massively sensitive and "bitey" feel. Also, increasing the MC piston size with everything else remaining the same reduces the hydraulic advantage
Simple formula:

Divide the total surface areas of all caliper pistons by the surface area of the MC

SoOon single caliper systems, aim for a ratio of around 13.5:1, whereas dual caliper systems aim for about 17:1.
On single calipers systems, anything below 12:1 will feel very wooden, and anything above 15:1 will be spongy. On twin caliper systems, below 15:1 results in a wooden lever, and above19:1 goes spongy.

So now you know.
And for reference, the Ducati 1299 uses the Brembo M50 calipers with a 16mm MC, not a 19!!!
So choose with care.

catso

16,584 posts

298 months

Wednesday 19th April 2017
quotequote all
I've got RCS masters on my Monster (brake 19mm and clutch 16mm) and also on the Guzzi brake (15mm) and I like them, also got a fixed ratio Brembo Radial (19mm x 20) on the 916 (model before the RCS was available).

They all work well, I prefer the RCS over the fixed as it has a brake-light switch, whereas the fixed ratio MC is designated as a 'race' piece and has no provision for a switch so I use a banjo pressure switch which has the downside of not always activating on gentle braking. Also the RCS have folding levers which could be handy if I drop the bike (although I believe the folding lever is now available on the fixed MC?).

The 19mm MC works well on both the Monster (which has M4 Monoblocs as per 1098/RSV4 etc.) and the 916 which has Bembo HPK calipers (same size pistons as M4 I believe?).

Both are excellent calipers but the Monoblocs on the Monster are more grabby (initial bite) even with the ratio set to the 'softer' more-feel (18 vs 20) setting whilst the HPK are more progressive. I doubt there's any difference in overall stopping power, only in the way it comes on - there must be some justification as to why HPK calipers cost twice as much as M4s...

I think the initial bite thing is the nature of the M4 caliper?, I have read many reviews and heard from 1098 owners that they are that way.

The HPK calipers are IME more progressive despite the fixed MC on my 916 having the harder (20) ratio but, of course I'm not comparing apples with apples here as the 916 has different discs and weighs more than the Monster which undoubtedly makes some difference.

In short, the RCS are great but may not solve the grabby initial bite, although the softer setting helps but this depends what ratio you have now? e.g. if your current MC is a 19 x 18 then fitting a 19RCS on the 18 setting won't make any difference, other than bling...

Wildfire

Original Poster:

9,951 posts

283 months

Wednesday 19th April 2017
quotequote all
Thanks guys. I'll have a look around. I actually want a bit more bite out of the MV, but as it's been a while since I rode it, I am unsure whether it is a consequence of the Ducati having more bite, or the pads on the MV needing replacing.

I believe the brake caliper diameter is 32mm per piston.

Steve Bass

10,758 posts

264 months

Wednesday 19th April 2017
quotequote all
Wildfire said:
Thanks guys. I'll have a look around. I actually want a bit more bite out of the MV, but as it's been a while since I rode it, I am unsure whether it is a consequence of the Ducati having more bite, or the pads on the MV needing replacing.

I believe the brake caliper diameter is 32mm per piston.
Initial "bite" is often a function of the pads rather then the hydraulic system. If you feel like you lack initial bite but your subsequent brake feel and modulation are good then your system is probably well configured and you needed to try a different pad compound. Different pads have different friction coefficients at different temperatures. So look for a compound with a higher low temperature friction coefficient

R1 Dave

7,158 posts

294 months

Wednesday 19th April 2017
quotequote all
Wildfire said:
Thanks guys. I'll have a look around. I actually want a bit more bite out of the MV, but as it's been a while since I rode it, I am unsure whether it is a consequence of the Ducati having more bite, or the pads on the MV needing replacing.

I believe the brake caliper diameter is 32mm per piston.
That's what I want out of my R1 brakes, there's no bite at the moment.

Wildfire

Original Poster:

9,951 posts

283 months

Wednesday 19th April 2017
quotequote all
Cheers Steve, I'll give them a go to start with (cheaper), but I do feel that the power is also lacking compared to the Ducati.

Steve Bass

10,758 posts

264 months

Wednesday 19th April 2017
quotequote all
Wildfire said:
Cheers Steve, I'll give them a go to start with (cheaper), but I do feel that the power is also lacking compared to the Ducati.
If you can find out the diameter of the MC piston it's easy to calculate your effective ratio.
If the callipers are Brembo just drop one off and double check the piston sizes. Many are 32/34mm rather than symmetrical.

Renn Sport

2,761 posts

240 months

Wednesday 19th April 2017
quotequote all
I would swap the brake pads to some SBS dual sintered fast road pads and refresh the brake fluid. Have a go and see if they feel better? This had a great effect on my old 750 track bike.

Also does your bike come with braided hoses? This also made a significant difference to me on that bike, where admittedly I would be braking quite hard. However the initial bite was very nice.

Lastly I found the Brembo RCS to make a MASSIVE difference on my track bikes. Perhaps a variable ratio RCS 19/18 or 18/17 would suit you as you have the option of changing the ratio depending on your feel.

I don't think you can go wrong really.