Check your bellypan bolts!
Check your bellypan bolts!
Author
Discussion

supermono

Original Poster:

7,464 posts

279 months

Thursday 20th April 2017
quotequote all
I recently had the misfortune of visiting a certain middlesex dyno / bike / scooter place with the 748SP and it came back with a great hole in the bellypan. Fortunately a chinese fairing not the beautiful pristine original that's tucked up safe.

It looked like a dzus was caught when rolling it backwards. Anyway they did the right thing and fixed it up for me after I made a small fuss, but I noticed they'd elected to only put one dzus in there. I confess I didn't do the right thing and remove / refit to check it was all ok.

Fast forward to yesterday's first trackday of the year -- end of straight flat out and a massive flash of yellow as both fairing lowers including bellypan ripped right off in the wind leaving the four upper frame fixings dzused intact with bits of fairing left. Basically it's written off the fairing including headlight part where it's ripped the holes out.

So moral of story (apart from being particular about where you take your bike) is watch out for that bellypan -- 150mph wind will get inside!

Thankfully nobody hurt/damaged.

trickywoo

14,287 posts

261 months

Thursday 20th April 2017
quotequote all
It's a shame but you really should give your bike the once over after someone else works on it.

My worse one was the mechanic not mounting the rear calliper properly after refitting the rear wheel.

Caliper spun and locked the rear wheel when the hose was trapped between the spindle and swing arm.

supermono

Original Poster:

7,464 posts

279 months

Thursday 20th April 2017
quotequote all
Totally. I always do my own work and never have a problem, you'd have thought the shop would get it right. Now I know better!

podman

9,087 posts

271 months

Thursday 20th April 2017
quotequote all
Having seen this happen on the road many years ago with a friend riding his 888, which ended up with him riding over his own lower fairing and nearly having him off, I check these periodically, the recently Firestorm shook 3 bolts out in a couple of hundred miles so both that and the LC have nylocks securing the bolts as well.

Unfortunately, as you have found, professionals do get it wrong too frequently, ignore reputations to a point & trust no one until proven is a good starting point.

supermono

Original Poster:

7,464 posts

279 months

Friday 21st April 2017
quotequote all
When I lived in Norfolk, CJ Ball at Hales/Norwich were the place -- specifically a bloke called Coddy we raced together and he was hyper meticulous. Although I still use them from the new bike even though it's a 150 mile ride each way I chanced this local place for the simple dyno run.

When you find a good mechanic you can trust they're really worth holding on to.

catso

16,584 posts

298 months

Friday 21st April 2017
quotequote all
The old 916 'angel wings'. wink

With just 2 Dzus fasteners underneath holding it together, great for a quick strip-down but if they fall out the whole thing opens up at speed like a pair of wings which then inevitably break off...

Prof Prolapse

16,163 posts

221 months

Friday 21st April 2017
quotequote all
I hadn't much experience of this until I got my newer bike. I did most of my stuff myself until then.

Asked for heated grips to be fitted, and the sales bloke said he'd have the detailer tidy the downpipes. They did a great job of both, apart from when the bar end fell off and nearly hit a mate behind me. After this I noticed a few more fairing fixtures were missing.

I returned it to them (quite fairly, they wanted to check themselves), and they allegedly checked it over. Then a crash bung fell off somewhere in the borders. Which again they reimbursed after a grumpy email from me. I declined letting them touch it again.

I have since changed garage, but now paranoia means I spent ten minutes last week checking someone elses work after paying someone to service it. The new garage is so far so good however.

Just one of those things I guess. I think a small amount of mechanical gumption and personal responsibility is still a prerequisite of running a motorcycle. So no hard feelings.











moanthebairns

19,183 posts

229 months

Friday 21st April 2017
quotequote all
I got a garage to fit goodbridge braided hoses to my bike when it was in for a service. I was going to order them but he said its fine ill get them. Having never touched a bike I flung it in, paid a high fee, then out on a run 50 miles from home noticed I had little to nil brake fluid. It had pished all over my calipers and pads at the banjo.

I took it back, and it took a week to fix, amongst other things. It still wasn't done right. I physically went down and saw the mechanic struggle with the lines, bleeding them into an irn bru bottle and he asked why I never bought goodridge or hel instead of these Chinese brands. The bd owner had charged me goodridge prices and bought cheap st.

He fked a set of pads with the fluid, telling me he's cleaned and treated them, they don't need replacing. I picked up the bike in the wet and flew right out at the first T-juction due to not being able to stop. He argued and spat the dummy that this was now costing him a set of pads, he replaced my ebcs with gold st.

It took about 3 weeks for the proper lines to get fitted and I have damage to the fork leg from the brake fluid... That told me to try to never use a mechanic again. Sadly sometimes I still do. But you always end up checking it as best as you can.

Prof Prolapse

16,163 posts

221 months

Friday 21st April 2017
quotequote all
Answer me this MTB, did you use a main dealer?

Or did you use the cheapest bloke you could find?


Birky_41

4,668 posts

215 months

Friday 21st April 2017
quotequote all
I've had this happen on both my track bikes and both had Dzus fasteners

Its almost as though the vibrations can make them come loose on certain panels? No good for the road but I just stick a tiny bit of tape over each one now and never had an issue

catso

16,584 posts

298 months

Friday 21st April 2017
quotequote all
Prof Prolapse said:
Answer me this MTB, did you use a main dealer?

Or did you use the cheapest bloke you could find?
Irn Bru bottle indeed, what next a deep fried Mars bar?... hehe

moanthebairns

19,183 posts

229 months

Friday 21st April 2017
quotequote all
catso said:
Prof Prolapse said:
Answer me this MTB, did you use a main dealer?

Or did you use the cheapest bloke you could find?
Irn Bru bottle indeed, what next a deep fried Mars bar?... hehe
he was a local dealer. Not a manufacture dealer but, certainly not bloke in the street. I bought the bike from there.

He promised he had a workshop next door and full time mechanic, wasnt till i saw it, some fat bd with a halfords socket set and a stand.

supermono

Original Poster:

7,464 posts

279 months

Friday 21st April 2017
quotequote all
Regarding the dzus -- yes tape a good idea but they are adjustable and can be made good and tight.

The bike without the "repair" spent a day around Spa last year and according to the previous owner, many a trackday throughout its life and there was never a problem.

I'm quite clear it was the dealer that hadn't done it right, but what you say about tape is something I'll definitely do in future thanks.

catso

16,584 posts

298 months

Friday 21st April 2017
quotequote all
moanthebairns said:
some fat bd with a halfords socket set and a stand.
OK, you caught me... biggrin

mckeann

2,996 posts

260 months

Friday 21st April 2017
quotequote all
Alex, there's a really good trustworthy mechanic in Bo'ness if you need it. Who did you use?

Biker's Nemesis

41,487 posts

239 months

Friday 21st April 2017
quotequote all
dzus or any type of fastener you can add an extra plastic washer to the bolt or you can cut an old inner tube into 10mm squares, fold them and cut a tiny bit out of the folded bit so that when you open it up you have a small hole in the middle, that does stop them vibrating loose as does the tape over the top.

Also make sure you have the right length and type of bolts for the fasteners.