Brembo
Author
Discussion

cbmotorsport

Original Poster:

3,065 posts

149 months

Thursday 29th June 2017
quotequote all
Everything seems to be fitted with Brembo brakes these days. Most new sportsbikes seem to have them. They're bloody good too. My BMW has them, they are the best brakes I've had on a bike.

Why are the likes of Nissin etc lagging behind, it's not just marketing hype, the Brembos are better. Nissin used to be the things to have on Jap sports bikes.


Prof Prolapse

16,163 posts

221 months

Thursday 29th June 2017
quotequote all
Tokico (Hitachi?) are standard fitment on the CBR1000RR 2017, not ridden it, but no significant critcisms of braking in mainstream media I'm aware of. So they con't be that bad.

Personally I think for most of us, it's just that we're suckers for brand. We make little use of it, but if consumers continue to push for a product a manufacturer will provide...

ETA: Also MT-10, similarly a flagship performance bike not critcised for braking, doesn't make use of Brembos unless you really want them does it?

Edited by Prof Prolapse on Thursday 29th June 11:34

Birky_41

4,667 posts

215 months

Thursday 29th June 2017
quotequote all
Surely some of it is brand? My ape has brembo - I think they are called M432? They are nice but the master cylinder is crap

My gsxr has Tokico and they are equally as good but not half as flash. I run a Accosota (however its spelt) master cylinder and that'll knock the spots of my ape for fade resistance

cbmotorsport

Original Poster:

3,065 posts

149 months

Thursday 29th June 2017
quotequote all
I guess Brembo is kind of synonymous with performance and motorsport, and they're generally quite blingy which appeals to the magpie tendencies in us all.

I've not ridden a new bike with Tokico or Nissins as standard, it just struck me that the Brembos were becoming the go to brake for performance bikes.

Brummmie

5,284 posts

252 months

Thursday 29th June 2017
quotequote all
Given similar technology brake system, the brand of pads will make more difference.

Mr OCD

6,388 posts

242 months

Thursday 29th June 2017
quotequote all
A lot of it is marketing hype... imho the TOKICO units on my blade were just as good as the BREMBO M4's I fitted. What made the biggest difference was actually changing the discs (Brembo) first, the pads second followed by the MC (Brembo RCS19) in that order.




sjtscott

4,215 posts

262 months

Thursday 29th June 2017
quotequote all
I've had some truely sh*te brakes (fully serviced, decent pads and fully working) on Japanese bikes over the years.
There is no marketing BS to state that the Brembo stuff on my Speed for me is awesome compared to some of these crap setups.
My Aprilia Falco had brembo setup same as the RSV and same as the Ducati 916 derivatives - they were great. I killed a set of EBCHH in 6k miles commuting on that bike no track work.

There are adequate systems, there are good systems and there are great systems. In principle there is nothing wrong with any of the brands its just what budget level the manufacturers put into the systems fitted to their bikes.
For me the worst front brakes of any sports bike let alone bike I've owned my 2003 GSXR600 - added braided lines made the lever solid better but still pants. Pads changed too - again didn't really help. It needed the Master cylinder and calipers junking and replacing basically I don't spend money on stuff like that.

MT10 was quoted as an example - I've test ridden one it has good brakes however in direct comparison to the brembo fronts on my Speed there is no contest in lever feel/initial bite/power - this is all personal and again like other things bike related some people can't tell any difference. My mate who also rode the MT10 thought they were brilliant - he doesn't however ride a Speed Triple or has had a bike with the same brembo system fitted so its all relative.

Edited by sjtscott on Thursday 29th June 12:16

sjtscott

4,215 posts

262 months

Thursday 29th June 2017
quotequote all
Mr OCD said:
A lot of it is marketing hype... imho the TOKICO units on my blade were just as good as the BREMBO M4's I fitted. What made the biggest difference was actually changing the discs (Brembo) first, the pads second followed by the MC (Brembo RCS19) in that order.
So genuine question why did you swop them? Other than branding/marketing hype? Did you fall foul of your own statement?

moanthebairns

19,181 posts

229 months

Thursday 29th June 2017
quotequote all
sjtscott said:
Mr OCD said:
A lot of it is marketing hype... imho the TOKICO units on my blade were just as good as the BREMBO M4's I fitted. What made the biggest difference was actually changing the discs (Brembo) first, the pads second followed by the MC (Brembo RCS19) in that order.
So genuine question why did you swop them? Other than branding/marketing hype? Did you fall foul of your own statement?
i genuinely think the standard brakes on my blade are fking awesome, the feel, feedback and performance really impressed me. I'd say its the best characteristic of the bike.

Why did you go for aftermarket for road use?

Birky_41

4,667 posts

215 months

Thursday 29th June 2017
quotequote all
Brummmie said:
Given similar technology brake system, the brand of pads will make more difference.
This with lines & a decent master cylinder

Brummmie

5,284 posts

252 months

Thursday 29th June 2017
quotequote all
Birky_41 said:
Brummmie said:
Given similar technology brake system, the brand of pads will make more difference.
This with lines & a decent master cylinder
If you swap the master cylinder for the same bore, then nothing has changed, given pivot ratio point is the same.

Mr OCD

6,388 posts

242 months

Thursday 29th June 2017
quotequote all
sjtscott said:
So genuine question why did you swop them? Other than branding/marketing hype? Did you fall foul of your own statement?
Two reasons...

1. The existing TOKICO's were due for new seals and a rebuild. A couple of pistons weren't looking clever either... Honda use this nasty cheap chromium coating on the pistons... as soon as they chip they start corroding ... the cost of a seal kit and a couple of pistons from Honda was the best part of £200 ...

2. I'm a Brembo we...

The M4's cost me brand new £400 delivered to my door which was an utter bargain... given the old ones would sell typically for £100-£120 minimum.

Man maths and man logic meant I got shiny new M4's biggrin

Mr OCD

6,388 posts

242 months

Thursday 29th June 2017
quotequote all
moanthebairns said:
i genuinely think the standard brakes on my blade are fking awesome, the feel, feedback and performance really impressed me. I'd say its the best characteristic of the bike.

Why did you go for aftermarket for road use?
- because I thought they were average at best
- because I've more money than sense
- because I love bling

... one or none of the above. biggrin

Prof Prolapse

16,163 posts

221 months

Thursday 29th June 2017
quotequote all
Mine came with the bike, and I wanted my model year because of other changes, but they do look cracking.

I'm with OCD on this one.


moanthebairns

19,181 posts

229 months

Thursday 29th June 2017
quotequote all
No one is going to deny they look the st, that is good enough reason....

Biker 1

8,614 posts

150 months

Thursday 29th June 2017
quotequote all
Bling. In a word. Just like Ohlins or Showa suspension, Bosch ABS, Renthal 'bars, etc etc. Are they really that much better than other branded stuff??
Another poster mentioned coatings to Honda brake pistons corroding; presumably the implication is that Brembo pistons don't corrode(??). Whatever, I would've thought the type & composition of brakepads would make the big difference.

fergus

6,430 posts

306 months

Thursday 29th June 2017
quotequote all
Brummmie said:
Birky_41 said:
Brummmie said:
Given similar technology brake system, the brand of pads will make more difference.
This with lines & a decent master cylinder
If you swap the master cylinder for the same bore, then nothing has changed, given pivot ratio point is the same.
Beside friction materials (mu), heat is the main cause of fade. Some of the cheaper m/c allow slight seal bleed when the m/c gets warm (from the fluid). The better offerings both maintain more thermal stability and hence have less of an issue and are also forged rather than cast, so are structurally stiffer, which means all the lever effort is acting in the correct plane on the piston all the time (same applies for high end calipers). Granted, this is for extreme (not road) use though. For a significant amount of cases 2 m/cs with the same bore and pivot fulcrums, etc, they will behave identically.

Birky_41

4,667 posts

215 months

Thursday 29th June 2017
quotequote all
fergus said:
Beside friction materials (mu), heat is the main cause of fade. Some of the cheaper m/c allow slight seal bleed when the m/c gets warm (from the fluid). The better offerings both maintain more thermal stability and hence have less of an issue and are also forged rather than cast, so are structurally stiffer, which means all the lever effort is acting in the correct plane on the piston all the time (same applies for high end calipers). Granted, this is for extreme (not road) use though. For a significant amount of cases 2 m/cs with the same bore and pivot fulcrums, etc, they will behave identically.
This is what I was told too. On road I have zero issues but on track its noticeable

Mr OCD

6,388 posts

242 months

Thursday 29th June 2017
quotequote all
Biker 1 said:
Another poster mentioned coatings to Honda brake pistons corroding; presumably the implication is that Brembo pistons don't corrode(??). .
The Brembo pistons have Titanium anodic oxidation coating to prevent corrosion.

Brummmie

5,284 posts

252 months

Thursday 29th June 2017
quotequote all
fergus said:
Brummmie said:
Birky_41 said:
Brummmie said:
Given similar technology brake system, the brand of pads will make more difference.
This with lines & a decent master cylinder
If you swap the master cylinder for the same bore, then nothing has changed, given pivot ratio point is the same.
Beside friction materials (mu), heat is the main cause of fade. Some of the cheaper m/c allow slight seal bleed when the m/c gets warm (from the fluid). The better offerings both maintain more thermal stability and hence have less of an issue and are also forged rather than cast, so are structurally stiffer, which means all the lever effort is acting in the correct plane on the piston all the time (same applies for high end calipers). Granted, this is for extreme (not road) use though. For a significant amount of cases 2 m/cs with the same bore and pivot fulcrums, etc, they will behave identically.
Thats why i said similar technology.