Is this fork knuckle f**ked?
Is this fork knuckle f**ked?
Author
Discussion

DuraAce

4,272 posts

191 months

Sunday 6th August 2017
quotequote all
Doesn't look great but might just be cracked paint /powder coat. I'd say it needs paint removal and inspection (especially on something so critical)

DuraAce

4,272 posts

191 months

Sunday 6th August 2017
quotequote all
Take it off the bike and I can X-ray it for you..

curlie467

7,650 posts

232 months

Sunday 6th August 2017
quotequote all
Whack the fker with a lump hammer, if it splits its fked.
Happy to help, anything else?

Birky_41

4,667 posts

215 months

Sunday 6th August 2017
quotequote all
Wouldn't risk it on something like that. As already said get it checked and welded if need be

CoolHands

23,712 posts

226 months

Sunday 6th August 2017
quotequote all
I wouldn't worry about it. Can't even notice it.

Tall_Paul

1,915 posts

258 months

Sunday 6th August 2017
quotequote all
If you look really closly you can see it's not a crack in the casting, it's part of the 'seam' that hasn't been joined properly and is flaking off (best way I can describle it!). Look here at the red areas, some of the alloy from the seam has broken off and you can see there's no crack in the actual fork leg. The 'seam' has overlapped and that's what looks like a crack.


Birky_41

4,667 posts

215 months

Sunday 6th August 2017
quotequote all
anonymous said:
[redacted]
My uncle is a fabricator in maldon. Company is called TAB FABRICATIONS. If you get stuck ping me an email and I'll see what he says

kev b

2,756 posts

197 months

Sunday 6th August 2017
quotequote all
It looks like casting flash but to be sure you need to dress it with a file or abrasive paper to see if there really is a crack.

No need for x rays etc until this simple check is done.

MrAverage

844 posts

158 months

Sunday 6th August 2017
quotequote all
I dunno where your based but I use a garage local too me in grays and the owner happens to be a welder by trade and does a fair bit of fab work. Thats Clint at full circle motorcycles.

You could ndt the fork with dye pen test. But it's probably easier to just wire brush it a bit see if it's a st bit of paint or wether it's failed.

Tall_Paul

1,915 posts

258 months

Sunday 6th August 2017
quotequote all
Yeah I reckon it's fine, this is what an actual cracked fork foot looks like frown I'll be getting this replaced over winter, a known issue on the Ohlins with the pinch bolts being done up by a monkey and overtorqued. £300 or thereabouts to have the bottom replaced.


Rubin215

4,201 posts

187 months

Sunday 6th August 2017
quotequote all
Tall_Paul said:
Yeah I reckon it's fine, this is what an actual cracked fork foot looks like frown I'll be getting this replaced over winter, a known issue on the Ohlins with the pinch bolts being done up by a monkey and overtorqued. £300 or thereabouts to have the bottom replaced.

I'll see your Ohlins and raise you a £200 ER5 with a previous ham-fisted owner...


DuraAce

4,272 posts

191 months

Sunday 6th August 2017
quotequote all
anonymous said:
[redacted]
Lincs unfortunately. Looks like you've dodged a bullet though. I'd still keep a closer eye on it for a few weeks to err on the side of caution.
Checked a marchesini front wheel for someone a couple of weeks ago who wasn't so lucky!

curlie467

7,650 posts

232 months

Sunday 6th August 2017
quotequote all
Good stuff!