Get my alarm removed or not?
Get my alarm removed or not?
Author
Discussion

Loyly

Original Poster:

18,295 posts

190 months

Thursday 17th August 2017
quotequote all
I've been thinking since I got my bike that I should probably get my alarm removed, and I'm wondering if it's worth it and if it's an easy enough job for an auto electrician.

I've got a 1997 T595 Daytona with an aftermarket Datatool system. It's an old system so it wouldn't surprise me if it had been supplied with the bike when it was first sold. I only have one alarm fob, which, whilst in fine working order, looks like st and has clearly been well used. I worry about losing it, to the point I have detached if from my key and I keep it in my pocket whilst riding.

I really don't need the alarm since the bike is never parked on the street. I had thought about getting it removed as it seems like more a hassle than a trying, when I envisage a scenario where I lose the fob and can't use the bike until the system is removed.

I asked my local Triumph dealer about getting rid of it last year and they said they'd only remove it to fit a new alarm system. I presume it's an easy enough job for most autoelectricians to perform, is it worth it?

2wheelsjimmy

624 posts

128 months

Thursday 17th August 2017
quotequote all
Probably take an alarm man 10mins to remove. Just find a local independent specialist.


Jazoli

9,707 posts

281 months

Thursday 17th August 2017
quotequote all
Yes remove it, or you can disable it with a simple jumper plug from triumph or by bridging two wires.

MotorsportTom

3,343 posts

192 months

Thursday 17th August 2017
quotequote all
Best way I have seen and you can do it yourself (all be it may make a bit of a mess), is cut wires from the alarm and after each cut check the bike starts.

I did it to my old blade and had no ill effects. Just had to wrap the ends of some of the wires where they went into the loom.

But definitely remove IMO.

cmaguire

3,589 posts

140 months

Thursday 17th August 2017
quotequote all
anonymous said:
[redacted]
Usually because old alarms drain the battery like crazy and never seem to work right anyway, and always have you worrying they will stop you using your own bike, whilst allowing anyone else to steal it because nobody pays any attention to alarm sirens now.

I removed one from a 2003 R1. Not rocket science. Wired into the indicators and wires to fuel pump/ignition and 12v to power itself. Usually the people that fit these (and claim to be auto-electricians) are so appallingly bad there will be blue scotch blocks/ birdst soldering/peeling insulation tape everywhere they've been so figuring out what they did is often disappointing but easy.

sjtscott

4,215 posts

262 months

Thursday 17th August 2017
quotequote all
Having been forced to have a Datatool on my brand new 1997 ZX6R at the time all it did was confirm they are a pain in the ass for the owner - and that was with the thing brand new. Carnell (now theres a blast from the past dealer chain wise) f**ked up and fitted it by mistake to my new bike - I hadn't requested it. When I picked up the bike I said I didn't ask for an alarm, they said sorry you'll need to pay for it - wrong I said ok you remove it or I won't buy the bike then I'll go elsewhere.
Quickly it was given for no extra cost but burdening me with it for the 3.5 years I owned the bike. I destested the crappy movement sensor and auto arming and beeps when in service mode and its battery flattening behaviour. Oh and the false alarms when I set it off.
Given this the EVO+ was way better in terms or being less oversensitive than the crappy system 3 fitted to my subsequently nicked GSXR600. Again alarm did nothing to stop the theft.

In summary I think I'd get the thing removed and be rid of the problem.

Private Pile

754 posts

226 months

Thursday 17th August 2017
quotequote all
Another vote to remove it. It's fairly straightforward to remove it yourself.

cbmotorsport

3,065 posts

149 months

Thursday 17th August 2017
quotequote all
Was a happy Datatool System 3 user on my Fireblade for 8 years. No problems. Didn't drain the battery, motion sensor was a bit annoying, but didn't bother me that much. Alarm was fitted to the bike when I bought it.

Then one day the alarm stopped responding to either fob, I couldn't disarm it and bike wouldn't start. I was miles from home.

Datatool don't offer replacement PCB's as they used to, so if it goes tits up it's junk and you're stuck. If you have no need for it, junk it.

Sea Demon

1,170 posts

244 months

Thursday 17th August 2017
quotequote all
Every alarm that I've had on a bike has gone wrong, when I buy bikes now I just get them removed because I don't trust them laugh

graham22

3,328 posts

236 months

Thursday 17th August 2017
quotequote all
Don't just cut the wires going to the alarm, some of the bikes wires may need re-joining as the alarm will sometimes sit 'in-line'.


Once you have a good look at the wiring & where it goes - little things like heading the length of the bike to flash a front indicator or a LED in the fairing, it will make sense where to disconnect.

The Datatool on my 2000 VFR800 wouldn't dis-arm due to the scotch block not making a good contact to the indicator. I successfully removed it one morning and I'm colour blind!

TwoStrokeNut

1,713 posts

272 months

Friday 18th August 2017
quotequote all
Another vote to get rid of the annoying bugger!

trickywoo

14,282 posts

261 months

Friday 18th August 2017
quotequote all
Another remove from me. I took a Meta out of my current bike, best 'mod' I've done.

An aftermarket alarm is a big factor putting me off buying a used bike.

Loyly

Original Poster:

18,295 posts

190 months

Friday 18th August 2017
quotequote all
I'm going to get a professional in to do it. I can see how it works but I don't trust myself to do it. My dad used to fit car alarms and stereos in the early 90's but he lives a bit far away to trouble with this, otherwise I would have dumped it on him.

The alarm fob was connected to the key with a really stty little bit of metal bent in a triangle shape which linked them together. One look at it and I imagined it flying off into a bush at 100mph in the middle of nowhere.

It's going, it's a load of st anyway and I won't be getting another! Thanks for the advice!

freddytin

1,184 posts

258 months

Friday 18th August 2017
quotequote all
Jazoli said:
Yes remove it, or you can disable it with a simple jumper plug from triumph or by bridging two wires.
^^^^^ Absolutely this, very easy and less than two minutes work .

TwoStrokeNut

1,713 posts

272 months

Friday 18th August 2017
quotequote all
trickywoo said:
Another remove from me. I took a Meta out of my current bike, best 'mod' I've done.

An aftermarket alarm is a big factor putting me off buying a used bike.
Yes, me too.

CaptainSlow

13,179 posts

243 months

Friday 18th August 2017
quotequote all
Quite topical as my DataTool 3 messed up a few weeks ago. No response from the fobs and the bike was dead.

Luckily I had the blanking plug so disconnected the alarm and don't miss it. Pain the back side.

CAPP0

20,881 posts

234 months

Friday 18th August 2017
quotequote all
I removed an alarm (can't remember the make now, was a common one at the time) from my Thunderace. I just followed the cables through, where they were piggybacked I cut them out, and where they were spliced in, I removed them and re-joined the two original ends together. Not difficult.

Loyly

Original Poster:

18,295 posts

190 months

Friday 18th August 2017
quotequote all
freddytin said:
^^^^^ Absolutely this, very easy and less than two minutes work .
How does this jumper plug trick work?

freddytin

1,184 posts

258 months

Friday 18th August 2017
quotequote all
Loyly said:
How does this jumper plug trick work?
I believe you can purchase one from Triumph, or the alarm supplier.

If someone is willing to give you the details, you could always short the two wires concerned wink

freddytin

1,184 posts

258 months

Friday 18th August 2017
quotequote all


The White plug which is attached to the alarm removed, followed by inserting black jumper plug into existing wiring loom.