What's up with my TS250?
Discussion
I've taken my newly-registered TS250 out a couple of times now but it has an annoying fault. If you ride it flat out, with the throttle pinned (and why wouldn't you?
) , it dies, as if it's being starved of fuel. If you back off, it comes back to life.
It's a Mikuni carb, some flavour of the VM28 but US Spec. It has a different throttle mech from my mate's UK 185 with the same carb, with a casing on the side of the carb which houses two cables for push/pull.
I thought it could be the filter on the top of the tap, inside the tank, but I switched it to reserve (to use the other filter) and it made no difference - in fact it may have been slightly worse. Fuel flows out of the hose OK when the tap is on, and the tank is at least half-full.
So then I thought about float height. It wasn't leaking or overflowing but when I checked, the float height was apparently much higher than it should be. It has those unattached floats which slide up & down on a small pole and then push the needle valve via a flat brass bar. Instructions online say to set the height from the gasket rim to the brass bar at 22-24mm upside down. Mine was set to about 10mm, so I moved it (but this will make the float shut off lower, not higher) and sure enough it runs worse now. I'm going to put the float height back where it was (or higher, avoiding overflows) and see how that goes.
I also need to ride it then pop the plug out to check colour, which I haven't done yet. I can't work out on this carb whether the needle height is adjustable, and if so how to do it. There's no obvious way to get at the needle without trying to take the overly-complex arm mechanism which lifts it, apart.
The air filter looks fairly new. It's not pristine clean but it's not knackered or blocked either.
Unless I'm imagining that it's fuel and it's electrics? I have a new plug I can chuck in but it doesn't feel like that. Could the HT insulation break down at high revs? But it comes back on as if the fuel is flowing again, and if you don't cane it, it runs OK.
Thanks all!
) , it dies, as if it's being starved of fuel. If you back off, it comes back to life.It's a Mikuni carb, some flavour of the VM28 but US Spec. It has a different throttle mech from my mate's UK 185 with the same carb, with a casing on the side of the carb which houses two cables for push/pull.
I thought it could be the filter on the top of the tap, inside the tank, but I switched it to reserve (to use the other filter) and it made no difference - in fact it may have been slightly worse. Fuel flows out of the hose OK when the tap is on, and the tank is at least half-full.
So then I thought about float height. It wasn't leaking or overflowing but when I checked, the float height was apparently much higher than it should be. It has those unattached floats which slide up & down on a small pole and then push the needle valve via a flat brass bar. Instructions online say to set the height from the gasket rim to the brass bar at 22-24mm upside down. Mine was set to about 10mm, so I moved it (but this will make the float shut off lower, not higher) and sure enough it runs worse now. I'm going to put the float height back where it was (or higher, avoiding overflows) and see how that goes.
I also need to ride it then pop the plug out to check colour, which I haven't done yet. I can't work out on this carb whether the needle height is adjustable, and if so how to do it. There's no obvious way to get at the needle without trying to take the overly-complex arm mechanism which lifts it, apart.
The air filter looks fairly new. It's not pristine clean but it's not knackered or blocked either.
Unless I'm imagining that it's fuel and it's electrics? I have a new plug I can chuck in but it doesn't feel like that. Could the HT insulation break down at high revs? But it comes back on as if the fuel is flowing again, and if you don't cane it, it runs OK.
Thanks all!
Hmm, you've checked most of the stuff I would look at. I would also be tempted to try it with another fuel line and dummy tank strapped up.
Is the float valve a genuine one in good nick? Aftermarket ones are usually bad news.
Those carbs also have a few air passages that can clog up. Sometimes even a few runs in an ultrasonic cleaner isn't enough.
Is it smoking much? How is the oil pump adjustment? Would be interesting to see the plug colour as suggested too.
Is the float valve a genuine one in good nick? Aftermarket ones are usually bad news.
Those carbs also have a few air passages that can clog up. Sometimes even a few runs in an ultrasonic cleaner isn't enough.
Is it smoking much? How is the oil pump adjustment? Would be interesting to see the plug colour as suggested too.
It's fuel starvation. And for the float height to be set where it is someone else has tried to fix the same issue. Higher float height results in richer fuelling.
Take the carb apart and thoroughly clean it. Remove all the jets and clean them out with fine wire.
Check the jetting against the recommended numbers. Also check it's the right carb for the bike. NOT unusual for a eager owner to change out carbs for mx type items and screw the bike up.
Replace the petcock fuel filter. This gave you a clue when it ran worse on reserve.
Make sure you have a good seal between the carb and the inlet rubber. Try squirting carb cleaner around the rubber at tickover and see if the motors revs increase.
How does it run at lower throttle openings? Crisp and responsive or still a little flat or unresponsive?
As Allan said, try the choke on at wot and see if it improves it. If so you're running lean or have fuel starvation at wot
But your problem is between the petcock and the carb.
Take the carb apart and thoroughly clean it. Remove all the jets and clean them out with fine wire.
Check the jetting against the recommended numbers. Also check it's the right carb for the bike. NOT unusual for a eager owner to change out carbs for mx type items and screw the bike up.
Replace the petcock fuel filter. This gave you a clue when it ran worse on reserve.
Make sure you have a good seal between the carb and the inlet rubber. Try squirting carb cleaner around the rubber at tickover and see if the motors revs increase.
How does it run at lower throttle openings? Crisp and responsive or still a little flat or unresponsive?
As Allan said, try the choke on at wot and see if it improves it. If so you're running lean or have fuel starvation at wot
But your problem is between the petcock and the carb.
Thanks guys, that's all really useful. I'll have another go at the weekend and report back.
I need to try and find out what the correct jets are so I can check that. The car is weird, it's like the VM28 but it has an extra bit on the side of it with a push/pull roller cam to operate the throttle, rather than just a cable in the top, and there's this weird right-angled activating arm which actually lifts the needle, which is the bit which I can't see how it comes apart. I wonder even whether it's something to do with US emissions so that it makes the needle not-changeable - then again, emissions rules on a stroker are a bit ridiculous!
By the way, re smoking, it smoked heavily when I got it running but it had been stood for who-knows how long. After a few miles it cleared off and is pretty normal now I think. I'll run it and whip the plug out at the weekend and stick a pic up.
I need to try and find out what the correct jets are so I can check that. The car is weird, it's like the VM28 but it has an extra bit on the side of it with a push/pull roller cam to operate the throttle, rather than just a cable in the top, and there's this weird right-angled activating arm which actually lifts the needle, which is the bit which I can't see how it comes apart. I wonder even whether it's something to do with US emissions so that it makes the needle not-changeable - then again, emissions rules on a stroker are a bit ridiculous!
By the way, re smoking, it smoked heavily when I got it running but it had been stood for who-knows how long. After a few miles it cleared off and is pretty normal now I think. I'll run it and whip the plug out at the weekend and stick a pic up.
CAPP0 said:
Thanks guys, that's all really useful. I'll have another go at the weekend and report back.
I need to try and find out what the correct jets are so I can check that. The car is weird, it's like the VM28 but it has an extra bit on the side of it with a push/pull roller cam to operate the throttle, rather than just a cable in the top, and there's this weird right-angled activating arm which actually lifts the needle, which is the bit which I can't see how it comes apart. I wonder even whether it's something to do with US emissions so that it makes the needle not-changeable - then again, emissions rules on a stroker are a bit ridiculous!
By the way, re smoking, it smoked heavily when I got it running but it had been stood for who-knows how long. After a few miles it cleared off and is pretty normal now I think. I'll run it and whip the plug out at the weekend and stick a pic up.
My guess: it's because of your face, or at least face related. I need to try and find out what the correct jets are so I can check that. The car is weird, it's like the VM28 but it has an extra bit on the side of it with a push/pull roller cam to operate the throttle, rather than just a cable in the top, and there's this weird right-angled activating arm which actually lifts the needle, which is the bit which I can't see how it comes apart. I wonder even whether it's something to do with US emissions so that it makes the needle not-changeable - then again, emissions rules on a stroker are a bit ridiculous!
By the way, re smoking, it smoked heavily when I got it running but it had been stood for who-knows how long. After a few miles it cleared off and is pretty normal now I think. I'll run it and whip the plug out at the weekend and stick a pic up.
nervous said:
CAPP0 said:
Thanks guys, that's all really useful. I'll have another go at the weekend and report back.
I need to try and find out what the correct jets are so I can check that. The car is weird, it's like the VM28 but it has an extra bit on the side of it with a push/pull roller cam to operate the throttle, rather than just a cable in the top, and there's this weird right-angled activating arm which actually lifts the needle, which is the bit which I can't see how it comes apart. I wonder even whether it's something to do with US emissions so that it makes the needle not-changeable - then again, emissions rules on a stroker are a bit ridiculous!
By the way, re smoking, it smoked heavily when I got it running but it had been stood for who-knows how long. After a few miles it cleared off and is pretty normal now I think. I'll run it and whip the plug out at the weekend and stick a pic up.
My guess: it's because of your face, or at least face related. I need to try and find out what the correct jets are so I can check that. The car is weird, it's like the VM28 but it has an extra bit on the side of it with a push/pull roller cam to operate the throttle, rather than just a cable in the top, and there's this weird right-angled activating arm which actually lifts the needle, which is the bit which I can't see how it comes apart. I wonder even whether it's something to do with US emissions so that it makes the needle not-changeable - then again, emissions rules on a stroker are a bit ridiculous!
By the way, re smoking, it smoked heavily when I got it running but it had been stood for who-knows how long. After a few miles it cleared off and is pretty normal now I think. I'll run it and whip the plug out at the weekend and stick a pic up.
As Unlucky Alf would have said:
oh, bugger
Luckily there is a plan at hand. Will you come and ride it for me? With your boyish pulchritude straddling the seat, mechanical order would be restored within half a mile, without a doubt.It sounds like fuel starvation as said above, filler cap vent is certainly one to look at (and probably the easiest to test - run with cap off!).
Another thought is the other end, could the exhaust be blocked? Either after years of two stroke oil carbon build up or a collapsed baffle in the pipe.
We regularly had to decoke pipes on all sorts of 2 strokes years ago, had to burn out the banana pipe on my TS185 as it was suffering similar issues.
Another thought is the other end, could the exhaust be blocked? Either after years of two stroke oil carbon build up or a collapsed baffle in the pipe.
We regularly had to decoke pipes on all sorts of 2 strokes years ago, had to burn out the banana pipe on my TS185 as it was suffering similar issues.
Assuming we are talking about a 70's TS250 this will help you out. http://www.mikuni.com/pdf/vmmanual.pdf
Just think yourself lucky you don't have 4 carbs to sort like my 70's Z's
Just think yourself lucky you don't have 4 carbs to sort like my 70's Z's
3200gt said:
Assuming we are talking about a 70's TS250 this will help you out. http://www.mikuni.com/pdf/vmmanual.pdf
Just think yourself lucky you don't have 4 carbs to sort like my 70's Z's
Thanks for the link.Just think yourself lucky you don't have 4 carbs to sort like my 70's Z's
I share your pain, I have 3 to get right on my Kettle!
Oh, kettle's, we like those. The needles on mikuni carbs are adjustable, its under the cap on the top side of the slide. The needle has 5 rings cut into it and a "E" clip into one of those grooves. normally the "E" clip is in groove 4 down from the top for UK climate. Moving it up a ring/s leans it off as the needle will sit lower and vice versa to richen it.
If you need any bits for the carb make sure you get genuine parts. Pattern parts will send you down another whole road of misery and grief. http://www.allensperformance.co.uk/shop/ all genuine mikuni and a fraction of the cost from bike shops.
If you need any bits for the carb make sure you get genuine parts. Pattern parts will send you down another whole road of misery and grief. http://www.allensperformance.co.uk/shop/ all genuine mikuni and a fraction of the cost from bike shops.
Edited by 3200gt on Friday 25th August 22:11
I've had an hour or so to bugger about with it today. Reset the float height, ignoring the online instructions I found and using good old Eyesight Mk. 1 to get it to a decent level in the bowl without overflowing. Bike is still doing it but definitely runs better than when I lowered the float height.
The floats seem OK, I haven’t checked them for leaks but they’re plastic, not brass so I’m hoping OK.
Float valve looks fine but no idea whether it’s original or not. All clear and blown through.
I’ve cleaned the whole carb out (and as Steve suggests below) but not ultrasonically.
It doesn’t smoke much at all once it’s been running a couple of minutes.
Here’s the plug after a run – brand new plug put in today. Looks about right to me??


Carb has been cleaned right through. Petcock looks new. I’ll pop it off and check the filters tomorrow and if they look dodgy, run it without to test.
I haven’t got a ref for standard jet sizes at present but that will be a good thing to check.
Haven’t tested for rubber leaks, but it runs really crisp all the way up to where it just suddenly dies off for a second or two, then it’s crisp again when it comes back. It definitely seems to be fuel starvation.
Chipchap said:
When it does this next time put the choke on. If it improves then its too lean and if it dies then its too rich. Change main jet for different size
At least I think I have that the right way round as its so long since I messed around with carburetted bikes.
A
Choke when it’s dying makes no difference, choke when it’s running properly just kills it.At least I think I have that the right way round as its so long since I messed around with carburetted bikes.
A
TwoStrokeNut said:
Hmm, you've checked most of the stuff I would look at. I would also be tempted to try it with another fuel line and dummy tank strapped up.
Is the float valve a genuine one in good nick? Aftermarket ones are usually bad news.
Those carbs also have a few air passages that can clog up. Sometimes even a few runs in an ultrasonic cleaner isn't enough.
Is it smoking much? How is the oil pump adjustment? Would be interesting to see the plug colour as suggested too.
I’ll have to see about another tank, kinda difficult to set up as it only does it over about 60mph!!Is the float valve a genuine one in good nick? Aftermarket ones are usually bad news.
Those carbs also have a few air passages that can clog up. Sometimes even a few runs in an ultrasonic cleaner isn't enough.
Is it smoking much? How is the oil pump adjustment? Would be interesting to see the plug colour as suggested too.
The floats seem OK, I haven’t checked them for leaks but they’re plastic, not brass so I’m hoping OK.
Float valve looks fine but no idea whether it’s original or not. All clear and blown through.
I’ve cleaned the whole carb out (and as Steve suggests below) but not ultrasonically.
It doesn’t smoke much at all once it’s been running a couple of minutes.
Here’s the plug after a run – brand new plug put in today. Looks about right to me??
podman said:
To add to the above, check the petrol cap breather isnt blocked as wel...
Thanks, tried that today, it’s not that!Steve Bass said:
It's fuel starvation. And for the float height to be set where it is someone else has tried to fix the same issue. Higher float height results in richer fuelling.
Take the carb apart and thoroughly clean it. Remove all the jets and clean them out with fine wire.
Check the jetting against the recommended numbers. Also check it's the right carb for the bike. NOT unusual for a eager owner to change out carbs for mx type items and screw the bike up.
Replace the petcock fuel filter. This gave you a clue when it ran worse on reserve.
Make sure you have a good seal between the carb and the inlet rubber. Try squirting carb cleaner around the rubber at tickover and see if the motors revs increase.
How does it run at lower throttle openings? Crisp and responsive or still a little flat or unresponsive?
As Allan said, try the choke on at wot and see if it improves it. If so you're running lean or have fuel starvation at wot
But your problem is between the petcock and the carb.
Float height reset manually today not to spec but to give a decent bowl level according to Eyesight Mk 1. Take the carb apart and thoroughly clean it. Remove all the jets and clean them out with fine wire.
Check the jetting against the recommended numbers. Also check it's the right carb for the bike. NOT unusual for a eager owner to change out carbs for mx type items and screw the bike up.
Replace the petcock fuel filter. This gave you a clue when it ran worse on reserve.
Make sure you have a good seal between the carb and the inlet rubber. Try squirting carb cleaner around the rubber at tickover and see if the motors revs increase.
How does it run at lower throttle openings? Crisp and responsive or still a little flat or unresponsive?
As Allan said, try the choke on at wot and see if it improves it. If so you're running lean or have fuel starvation at wot
But your problem is between the petcock and the carb.

Carb has been cleaned right through. Petcock looks new. I’ll pop it off and check the filters tomorrow and if they look dodgy, run it without to test.
I haven’t got a ref for standard jet sizes at present but that will be a good thing to check.
Haven’t tested for rubber leaks, but it runs really crisp all the way up to where it just suddenly dies off for a second or two, then it’s crisp again when it comes back. It definitely seems to be fuel starvation.
Jazzy Jag said:
2 strokes can be susceptible to crank shaft seals leaking air into the crank case , especially if they have been stood and dried out.
I had the same problems with a Suzuki Katana scooter many years ago.
Bloody hope it’s not that! But it runs fine the rest of the time so I think not?I had the same problems with a Suzuki Katana scooter many years ago.
graham22 said:
It sounds like fuel starvation as said above, filler cap vent is certainly one to look at (and probably the easiest to test - run with cap off!).
Another thought is the other end, could the exhaust be blocked? Either after years of two stroke oil carbon build up or a collapsed baffle in the pipe.
We regularly had to decoke pipes on all sorts of 2 strokes years ago, had to burn out the banana pipe on my TS185 as it was suffering similar issues.
Hmm, there’s no sign that it’s blocked but I haven’t thoroughly checked that yet. How would you clean it? Caustic?Another thought is the other end, could the exhaust be blocked? Either after years of two stroke oil carbon build up or a collapsed baffle in the pipe.
We regularly had to decoke pipes on all sorts of 2 strokes years ago, had to burn out the banana pipe on my TS185 as it was suffering similar issues.
That plug looks a bit lean to me.
I wonder if you have some sort of Mikuni knock-off, there's been a few about. It sounds like it's a main jet issue, check the size and buy the next one up from Allens, it'll be cheaper than a holed piston.
If you can find a kind soul with a TS250 try swapping carbs, a long shot I know.
And NEVER use pattern jets.
I wonder if you have some sort of Mikuni knock-off, there's been a few about. It sounds like it's a main jet issue, check the size and buy the next one up from Allens, it'll be cheaper than a holed piston.
If you can find a kind soul with a TS250 try swapping carbs, a long shot I know.
And NEVER use pattern jets.
CAPP0 said:
graham22 said:
It sounds like fuel starvation as said above, filler cap vent is certainly one to look at (and probably the easiest to test - run with cap off!).
Another thought is the other end, could the exhaust be blocked? Either after years of two stroke oil carbon build up or a collapsed baffle in the pipe.
We regularly had to decoke pipes on all sorts of 2 strokes years ago, had to burn out the banana pipe on my TS185 as it was suffering similar issues.
Hmm, there’s no sign that it’s blocked but I haven’t thoroughly checked that yet. How would you clean it? Caustic?Another thought is the other end, could the exhaust be blocked? Either after years of two stroke oil carbon build up or a collapsed baffle in the pipe.
We regularly had to decoke pipes on all sorts of 2 strokes years ago, had to burn out the banana pipe on my TS185 as it was suffering similar issues.
With black systems, again have got them red hot to burn out, obviously repainting afterwards - you'll be surprised how much smoke comes out of them!!
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff


