Quick relay question
Discussion
If you use a normal relay check if you need a diode across the coil pins to stop back emf.
Simple 1N4001 from Maplin or RS Components will do and cost about 3 pence.
Look online for the way to connect it up.. easy peasy
Also make sure you get a relay with a decent current switching capacity. Motors draw high start current and the arcing across the relay contacts can damage it very quickly
Simple 1N4001 from Maplin or RS Components will do and cost about 3 pence.
Look online for the way to connect it up.. easy peasy
Also make sure you get a relay with a decent current switching capacity. Motors draw high start current and the arcing across the relay contacts can damage it very quickly
Edited by Steve Bass on Sunday 3rd September 10:13
At least it didn't get broken for spares then.
The issue with a non-standard relay is that the OE connector may have to be cut off and new connector(s) used for the traditional replacement.
And the replacement is unlikely to be waterproof as your OE one looks like it is, possibly due to location on the bike.
Bike breakers would be most convenient solution
The issue with a non-standard relay is that the OE connector may have to be cut off and new connector(s) used for the traditional replacement.
And the replacement is unlikely to be waterproof as your OE one looks like it is, possibly due to location on the bike.
Bike breakers would be most convenient solution
Thanks for the replies Steve & CM.
Would you believe my local car spare didn't have a 4 pin relay
Think I'll wait till tomorrow and get an OE one.
Chaps, do you have any idea how many earth points are on a bike normally? I found one so far. Thought it might be a good idea to clean them all and apply a bit of Vaseline to prevent future corrosion.
Would you believe my local car spare didn't have a 4 pin relay

Think I'll wait till tomorrow and get an OE one.
Chaps, do you have any idea how many earth points are on a bike normally? I found one so far. Thought it might be a good idea to clean them all and apply a bit of Vaseline to prevent future corrosion.
Well, as usual with this c**ting bike, the relay wasn't the issue. New one in and still no dice.
Next culprit, apparently, is the immobiliser. What a f
king mission that's going to be to uninstall that.
But I assume that's the issue. Power goes into the relay (red wire), power comes out of the relay (black wire). But it doesn't tick when the ignition turns on. In the same way the pump doesn't prime. But then it wouldn't, there's no power getting there.
So in between the relay and the pump is the immobiliser. Right? Close to slitting my wrists here.....
Next culprit, apparently, is the immobiliser. What a f
king mission that's going to be to uninstall that.But I assume that's the issue. Power goes into the relay (red wire), power comes out of the relay (black wire). But it doesn't tick when the ignition turns on. In the same way the pump doesn't prime. But then it wouldn't, there's no power getting there.
So in between the relay and the pump is the immobiliser. Right? Close to slitting my wrists here.....
caduceus said:
Well, as usual with this c**ting bike, the relay wasn't the issue. New one in and still no dice.
Next culprit, apparently, is the immobiliser. What a f
king mission that's going to be to uninstall that.
But I assume that's the issue. Power goes into the relay (red wire), power comes out of the relay (black wire). But it doesn't tick when the ignition turns on. In the same way the pump doesn't prime. But then it wouldn't, there's no power getting there.
So in between the relay and the pump is the immobiliser. Right? Close to slitting my wrists here.....
When are you checking the fuel pump only as I mentioned on the previous post, the fuel pump on the ZX6R G1&2 does not prime when you turn the ignition on, it only operates when the starter button is pushed or the engine is running.Next culprit, apparently, is the immobiliser. What a f
king mission that's going to be to uninstall that.But I assume that's the issue. Power goes into the relay (red wire), power comes out of the relay (black wire). But it doesn't tick when the ignition turns on. In the same way the pump doesn't prime. But then it wouldn't, there's no power getting there.
So in between the relay and the pump is the immobiliser. Right? Close to slitting my wrists here.....
I would also doubt there is an immobiliser between the relay and the pump, most just cut the ignition and or starter circuit.
Thanks for that Pozi. I'll disconnect the starter motor and turn it over whilst checking the power to the pump again.
The splicing for the immobiliser does include the fuel pump. I've already unwrapped the black tape and found it.
If I do find power to the fuel pump whilst cranking, I have a funny feeling I'm never going to find out what the problem is.
The splicing for the immobiliser does include the fuel pump. I've already unwrapped the black tape and found it.
If I do find power to the fuel pump whilst cranking, I have a funny feeling I'm never going to find out what the problem is.
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff


