Removing news pads from monobloc calipers
Removing news pads from monobloc calipers
Author
Discussion

shielsy

Original Poster:

826 posts

160 months

Tuesday 5th September 2017
quotequote all
Had to do a couple of jobs on the bike last weekend... Nothing major; front pads, fluid and front wheel alignment.

Did the business and threw it back together. As is often the case the alignment wasn't perfect on the first attempt so tried again. I was getting a small amount of rubbing on one caliper so opted to push the pistons all the way back and let it re-seat with my now-aligned front wheel.

Now with the Brembo M4 there is ample room to remove worn pads, but not new ones unless you push one of the pads back. See here:



Due to the fact I needed to get the job done I ended up prying them with a flat object. This ends up fking the pads though which I'd rather avoid the next time I'm presented with this problem.

So how do you do it?

Biker's Nemesis

41,487 posts

239 months

Tuesday 5th September 2017
quotequote all
Take worn pads out which will leave the pistons exposed, clean the pistons with a tooth brush using brake cleaner then a bit of WD40 wiping off any excess.

Re fit the old pads and lever back the pistons with anything you like.

Take the old pads out again which will leave plenty of room too fit the new pads

Jazoli

9,707 posts

281 months

Tuesday 5th September 2017
quotequote all
Push the pistons back in with your thumbs before you put the pads in, or use one of these, or the old pads as BN has already said.



https://www.amazon.co.uk/OTC-OTC4743-Motorcycle-Ca...

Edited by Jazoli on Tuesday 5th September 13:13

shielsy

Original Poster:

826 posts

160 months

Tuesday 5th September 2017
quotequote all
To be clear, new pads need to be pushed back in order to remove them and therefore access the pistons.

Order of events

Old pads removed, pistons cleaned and pushed back
New pads fitted
Pads pushed up against the disc
Now I need to remove the new pads

For what it's worth, I've finished the job and everything is fine. I just want to know how to do it without fking the pads the next time I need to remove them.

Mr OCD

6,388 posts

242 months

Tuesday 5th September 2017
quotequote all
shielsy said:
Now with the Brembo M4 there is ample room to remove worn pads, but not new ones unless you push one of the pads back. See here:



Due to the fact I needed to get the job done I ended up prying them with a flat object. This ends up fking the pads though which I'd rather avoid the next time I'm presented with this problem.

So how do you do it?
It's due to the pin-less design which frankly I found a total pain the arse. Even seating the pads can be fiddly.

For the new pad issue. i.e. removal I just use a piece of wood between the pads and twist it gently to seat the pistons on one side so the pads can be removed. The annoying thing is if the pads are nearly new but the pistons are covered in st from the road you can't take the pads out to clean the pistons without pushing the pistons back slightly and hence all the crap into the seals...




Biker's Nemesis

41,487 posts

239 months

Tuesday 5th September 2017
quotequote all
The pads should be able to be gently pushed back using a screwdriver without buggering the pads.

Jazoli and OCD have both suggested good ideas for pushing the pads back.

Biker's Nemesis

41,487 posts

239 months

Tuesday 5th September 2017
quotequote all

I sometimes use these car trim clip removers which do a great job of not damaging pads



moanthebairns

19,181 posts

229 months

Tuesday 5th September 2017
quotequote all
I use a screwdriver.... posh s

Prof Prolapse

16,163 posts

221 months

Tuesday 5th September 2017
quotequote all
I just levered mine.

You can use this sort of thing if you're st;


Jazoli

9,707 posts

281 months

Tuesday 5th September 2017
quotequote all
Biker's Nemesis said:
I sometimes use these car trim clip removers which do a great job of not damaging pads


I like your style biggrin

Prof Prolapse

16,163 posts

221 months

Tuesday 5th September 2017
quotequote all
That piece of paper must be at least 70 years old.

mckeann

2,996 posts

260 months

Tuesday 5th September 2017
quotequote all
A large flat blade screwdriver always does the job for me. If the pistons are moving freely, it shouldn't take much effort to prise them open

CarsOrBikes

1,158 posts

215 months

Tuesday 5th September 2017
quotequote all
I'd just twist the caliper using the disc itself to spread the pads, if worried about that dirt being drawn into calipers, remove old pads, clean up, refit old, spread as intended, continue with renewal. What's not to like?

Biker's Nemesis

41,487 posts

239 months

Tuesday 5th September 2017
quotequote all
Prof Prolapse said:
That piece of paper must be at least 70 years old.

Mr OCD

6,388 posts

242 months

Wednesday 6th September 2017
quotequote all
CarsOrBikes said:
, if worried about that dirt being drawn into calipers, remove old pads, clean up, refit old, spread as intended, continue with renewal. What's not to like?
Again, you can't do that with Brembo M4's without pushing the pistons back to remove the pads... i.e. the pads won't come out due to the pinless design.

Mr OCD

6,388 posts

242 months

Wednesday 6th September 2017
quotequote all
anonymous said:
[redacted]
Yes, that's right. smile

graeme4130

3,956 posts

212 months

Wednesday 6th September 2017
quotequote all
There's loads of specific tools that will be kinder to the pads, but I tend to just use a 1" wide tyre lever and be very gentle with it with new pads.
To remove the pistons, you do need a removal tool though, and even then it's still a ball ache.
The more often you do it, the easier they are to remove as they're obviously cleaner, and you can just about do it by hand at times. The other method to make piston removal easier is the leave them in some very hot water for a few mins to put some heat in the seals and soften them up

Biker's Nemesis

41,487 posts

239 months

Wednesday 6th September 2017
quotequote all
Brake piston removal tool used on my old 04 R1 track bike.


Biker's Nemesis

41,487 posts

239 months

Wednesday 6th September 2017
quotequote all
All modern front calipers on sports bikes are opposed pistons

shielsy

Original Poster:

826 posts

160 months

Wednesday 6th September 2017
quotequote all
anonymous said:
[redacted]
If the pads are toast they can be removed without moving the pistons. But if they have some meat on them you do have to push the (probably filthy) pistons in to remove the pads.