Egr
Author
Discussion

Benny1003

Original Poster:

10 posts

110 months

Wednesday 6th September 2017
quotequote all
Hello everyone

I'm thinking of changing the exhaust on my motorbike but I'm worried that if I take the EGR pipe and blank it off wether or not it will knacker my engine. Has anyone done this and mashed their engine up or does it just make the bike run a bit lean and a bit hotter?

Thanks
Ben

gavgavgav

1,569 posts

260 months

Wednesday 6th September 2017
quotequote all
It may depend on the design for this question, on the Hornet it ejects clean air in the exhaust header, after the engine has done its thing. No impact what-so ever on the engine.

Benny1003

Original Poster:

10 posts

110 months

Wednesday 6th September 2017
quotequote all
It's a Yamaha ybr

bimsb6

8,808 posts

252 months

Wednesday 6th September 2017
quotequote all
anonymous said:
[redacted]
I doubt it has an egr on it .

Benny1003

Original Poster:

10 posts

110 months

Wednesday 6th September 2017
quotequote all
Well I put the same thing on a different forum about changing my exhaust and asked what the small pipe was coming off my exhaust and some bloke had a right pop at me talking nonsense about things I didn't even ask and he said it was an egr and a few other people agreed with him so that's why I thought it was an egr. But i didn't bother going back to that forum after asking a question and someone bit my head off about it so that's why I'm on here asking you guys and see if you can steer me in the right direction and or give me advice on bits

MotorsportTom

3,343 posts

192 months

Wednesday 6th September 2017
quotequote all
Year of bike? Any photos of said pipe and location?

Benny1003

Original Poster:

10 posts

110 months

Wednesday 6th September 2017
quotequote all



So that's the pipe on the picture and it's a 2014

MotorsportTom

3,343 posts

192 months

Wednesday 6th September 2017
quotequote all
A quick google and as I thought based on that picture it seems as though it's pipe that sucks air from, not blows air into, the airbox.

I can't see why removing it/blanking it off would cause any ill effects.

Benny1003

Original Poster:

10 posts

110 months

Wednesday 6th September 2017
quotequote all
Well as I said before on the last forum I had my head bitten off but the fella was going on about something like it takes some of the gases from the exhaust back into th engine for a second burn don't know if that's right or not? I don't know much about these things as this is my first bike and I suppose it's trial and error with help from you guys along the way but thanks for all the help so far really appreciate it!

Olivergt

2,288 posts

112 months

Wednesday 6th September 2017
quotequote all
I'm no expert, but if the tube simply goes from the exhaust to the airbox then there is no way the flow of the exhaust past the end of the tube will be sufficient to suck air from the airbox. On the other hand the suction caused by the pistons will have plenty of power to suck exhaust gas into the airbox.

So to me it sounds like a very simple EGR mechanism.

I would go ahead with your changes, but keep all the old parts just in case.

As you mentioned, the only thing that might happen is that the engine will run a little lean, but if it is ECU controlled its should be able to compensate fueling etc/

Benny1003

Original Poster:

10 posts

110 months

Wednesday 6th September 2017
quotequote all
Olivergt said:
I'm no expert, but if the tube simply goes from the exhaust to the airbox then there is no way the flow of the exhaust past the end of the tube will be sufficient to suck air from the airbox. On the other hand the suction caused by the pistons will have plenty of power to suck exhaust gas into the airbox.

So to me it sounds like a very simple EGR mechanism.

I would go ahead with your changes, but keep all the old parts just in case.

As you mentioned, the only thing that might happen is that the engine will run a little lean, but if it is ECU controlled its should be able to compensate fueling etc/
Thank you, appreciate your help smile

Rubin215

4,201 posts

187 months

Wednesday 6th September 2017
quotequote all
It's not egr, it just allows air from the airbox into the exhaust to lower emissions when tested.

You can change the exhaust easily without causing any damage, just make sure and close off the hole into the airbox (fold the rubber hose over and cable tie it).

Bearing in mind, that if your are changing the exhaust to try and improve performance the gains are minimal for the cost.

Krikkit

27,941 posts

212 months

Wednesday 6th September 2017
quotequote all
As above, it doesn't look like an inlet link, but a crankcase breather, using the exhaust velocity rushing past the end of the pipe to draw out the vapours from the exhaust.

If it was EGR I'd expect it to be a metal pipe all the way into the engine as well, EGR flow is often water-cooled in the car world (obviously not as much room for that on the bike, but makes a point).

Benny1003

Original Poster:

10 posts

110 months

Wednesday 6th September 2017
quotequote all
Rubin215 said:
It's not egr, it just allows air from the airbox into the exhaust to lower emissions when tested.

You can change the exhaust easily without causing any damage, just make sure and close off the hole into the airbox (fold the rubber hose over and cable tie it).

Bearing in mind, that if your are changing the exhaust to try and improve performance the gains are minimal for the cost.
Thanks for your help and yes I was aware that it wouldn't do much performance wise but the reason for thinking about changing is the standard one on it is getting very rusty and doesn't look the best so just wanted to put some stainless on it and make it look a little nicer.
But thanks for your help smile

gavgavgav

1,569 posts

260 months

Wednesday 6th September 2017
quotequote all
anonymous said:
[redacted]
I know, it's called a PAIR valve on the Hondas. He has a good question and all he wanted to know if he will knacker his engine, the important bit is that it wont.

crofty1984

17,064 posts

235 months

Thursday 7th September 2017
quotequote all
I had a YBR. The exhaust finish is terrible. I got some heatproof black paint and some heatproof top clear coat and it came up a treat. Only an afternoon's work, including taking it off and replacing it. It was a brilliant bike for what it did though. Also, the rear sprocket and chain are different between the custom and standard models.

Benny1003

Original Poster:

10 posts

110 months

Thursday 7th September 2017
quotequote all
crofty1984 said:
I had a YBR. The exhaust finish is terrible. I got some heatproof black paint and some heatproof top clear coat and it came up a treat. Only an afternoon's work, including taking it off and replacing it. It was a brilliant bike for what it did though. Also, the rear sprocket and chain are different between the custom and standard models.
Yea they are a lovely little bike and I had it about 3 years but for the past year I hadn't been able to afford to us it because of getting a car and only being on apprentice money but just getting it back out on the road and doing a few minor repairs and cleaning it up so hopefully this time next month I'll be back out on it smile

Rubin215

4,201 posts

187 months

Thursday 7th September 2017
quotequote all
Benny1003 said:
crofty1984 said:
I had a YBR. The exhaust finish is terrible. I got some heatproof black paint and some heatproof top clear coat and it came up a treat. Only an afternoon's work, including taking it off and replacing it. It was a brilliant bike for what it did though. Also, the rear sprocket and chain are different between the custom and standard models.
Yea they are a lovely little bike and I had it about 3 years but for the past year I hadn't been able to afford to us it because of getting a car and only being on apprentice money but just getting it back out on the road and doing a few minor repairs and cleaning it up so hopefully this time next month I'll be back out on it smile
The other maintenance thing on them that gets ignored is greasing the swingarm bearings; they slowly seize, the swingarm starts to flex and eventually snaps.

Benny1003

Original Poster:

10 posts

110 months

Thursday 7th September 2017
quotequote all
Rubin215 said:
The other maintenance thing on them that gets ignored is greasing the swingarm bearings; they slowly seize, the swingarm starts to flex and eventually snaps.
Thanks I'll keep that in mind and look at that smile