Pinlock visors
Author
Discussion

pessimal

Original Poster:

339 posts

112 months

Wednesday 13th September 2017
quotequote all
had a new visor and pinlock on my caberg helmet a few months ago, and its been fine up till now.

i dont know if pinlocks shrink, but all of a sudden i have a large gap at the bottom of the pinlock causing the visor to mist up.

Does anyone have any tips on adjusting the pinlock to fit better.

when i have tried adjusting it before with a pair of pliers to try and rotate the pin, i end up chewing the pin up, and the pinlock not fitting well on one side.

i'm not sure whats best to use to adjust the pin, or if its just better to take it into the shop i bought it from and let them adjust it.

thanks




sjtscott

4,215 posts

262 months

Wednesday 13th September 2017
quotequote all
Google is your friend.. have a look for the pinlock website where they have instructions for doing this adjustment correctly.
Basically the indicator on the pins needs to be turned towards each other i.e. facing into the visor to tighten the seal, they say the pinlock insert has to come off to do this. I found I had a small perfectly fitting odd sized socket to help me turn enough with my fingers in situe - I wouldn't use pilers.
> < = tightest position

cpl_payne

576 posts

214 months

Wednesday 13th September 2017
quotequote all
Yes, read all of the above carefully and you may find that after you spend 15 minutes lovingly washing everything, putting the pinlock in place and carefully adjusting the pins you'll discover that the inside of the visor (i.e. the pinlock) now scrapes the rubber seal at the top of the lid just enough to push the pinlock out of place each time you lift the visor, rendering the whole ing excercise pointless and you're looking at the gap between the bottom of the pinlock and the visor.

Why the fking fk the s charging several hundred for a helmet with a good £50 for a visor haven't come up with a fking permanent solution which does not require twisting two fking clits with tweezers with bated breath is anyone's guess.


milleplod

40 posts

227 months

Wednesday 13th September 2017
quotequote all
Every one of the Shark helmets I've had has been equipped with a visor that has an anti-mist coating....and it works. However, their latest ones do have visors that are 'Pinlock ready'......as well as the anti-fog treatment!.......because customers 'expect' Pinlock. Presumably some folk actually look forward to all the faffing about!

Pete

RizzoTheRat

29,143 posts

223 months

Wednesday 13th September 2017
quotequote all
Part of the advantage of pinlocks is they're effectively double glazing, anti fog coatings are good but keeping the inner surface warmer makes a difference.
As said above bend the sides of your visor apart to flatten it slightly before trying to adjust the pinlock.

creampuff

6,511 posts

174 months

Wednesday 13th September 2017
quotequote all
pessimal said:
had a new visor and pinlock on my caberg helmet a few months ago, and its been fine up till now.

i dont know if pinlocks shrink, but all of a sudden i have a large gap at the bottom of the pinlock causing the visor to mist up.

Does anyone have any tips on adjusting the pinlock to fit better.
Having had several pinlocks, IMHO they last 6 months, then they are fked, then you have to buy a new one.

creampuff

6,511 posts

174 months

Wednesday 13th September 2017
quotequote all
cpl_payne said:
fking fk the s fking fking clits
cpl_payne has eloquently described the pinlock situation.

pessimal

Original Poster:

339 posts

112 months

Wednesday 13th September 2017
quotequote all
sjtscott said:
Google is your friend.. have a look for the pinlock website where they have instructions for doing this adjustment correctly.
Basically the indicator on the pins needs to be turned towards each other i.e. facing into the visor to tighten the seal, they say the pinlock insert has to come off to do this. I found I had a small perfectly fitting odd sized socket to help me turn enough with my fingers in situe - I wouldn't use pilers.
> < = tightest position
you managed to find a small socket to put over the pinlock pin to turn it?

what sort of size was it?

cheers

boyse7en

8,237 posts

196 months

Wednesday 13th September 2017
quotequote all
creampuff said:
Having had several pinlocks, IMHO they last 6 months, then they are fked, then you have to buy a new one.
What are you doing with them?? The one in my Schuberth has just been replaced after 4 years almost daily use and about 30,000 miles.

Wildfire

9,951 posts

283 months

Wednesday 13th September 2017
quotequote all
boyse7en said:
What are you doing with them?? The one in my Schuberth has just been replaced after 4 years almost daily use and about 30,000 miles.
I was about to say the same thing. Mine has about 40,000k on it and is 5 years old, and it's just about misting on very cold days.

RizzoTheRat

29,143 posts

223 months

Thursday 14th September 2017
quotequote all
Same here, my Schuberth's old enough that I'm thinking I really need to replace it pretty soon and I'm still on the original pinlock. I did get a bit of trouble with it steaming up at the bottom between the layers a couple of years ago but I took it out, gave everything a clean, ensured it was seated properly when I put it back in, and have had no more trouble.

CAPP0

20,881 posts

234 months

Thursday 14th September 2017
quotequote all
Once you have re-seated it, go round the edge with the corner of a piece of paper. If the paper slips under anywhere then the pillock isn't seated yet.

A colder morning this week reminded me that mine "rides up" at the bottom and needs to be clicked back into place occasionally.

pessimal

Original Poster:

339 posts

112 months

Thursday 14th September 2017
quotequote all
getting more tempted just to stick some duct tape around the outside of it and have done!

tried to get one of the pinlock pins out last night and was unable to, i need to find something to rotate them in place.

leighz

473 posts

163 months

Thursday 14th September 2017
quotequote all
never managed to get a pinlock to work properly either - foggy respro masks (or similar) work really well though

Wildfire

9,951 posts

283 months

Thursday 14th September 2017
quotequote all
pessimal said:
getting more tempted just to stick some duct tape around the outside of it and have done!

tried to get one of the pinlock pins out last night and was unable to, i need to find something to rotate them in place.
How do you mean out? Mine have a little hex adjuster on the inside, gentle work with pliers or a if you have atiny socket should do it. You shouldn't have to take them out at all.

Take the visor out, remove the pinlock ( you need to flatten the visor), wash it all down and let it dry, set the pins to neutral (using the little arrows) and reinstall. Then adjust the pins and gibe it a wiggle until it is seated correctly.

RizzoTheRat

29,143 posts

223 months

Thursday 14th September 2017
quotequote all
anonymous said:
[redacted]
Catcrap works fairly well (no not out of a feline, have a search on e-bay), but I found changing to a helmet with better ventilation made the biggest different, it has to be seriously cold out for my glasses to team up in my Schuberth C3, where as it was a pain in the arse in my Shoei Raid.

pessimal

Original Poster:

339 posts

112 months

Monday 25th September 2017
quotequote all
got it sorted.

all this talk of hex and crossheads had me confused.

i have this type of pinlock pin rather than

in the end i had to use brute force to pop the pin out (causing a tiny crack in the visor in the process) rotate it, and them pop in back in with even more force!

think i might buy some of the pinlock pins with the screw or hex in them to make this a little less frustrating next time

tivver500

376 posts

301 months

Monday 25th September 2017
quotequote all
My recent glasses (vari-focal) have an 'anti-glare' coating - works well to prevent glare but it also stops any anti-mist coating from working frown. When out on the bike (or skiing) I have to go back to my old bi-focals which take the anti mist fine....
Alternatively - remove glasses and work on 'zen navigation' much more fun

SVS

3,824 posts

302 months

Monday 25th September 2017
quotequote all
You need glasses with Essilor’s OptiFog lenses. Great quality lenses and utterly brilliant for eliminating fogging thumbup

Desiato

960 posts

314 months

Monday 25th September 2017
quotequote all
anonymous said:
[redacted]
I use RainX anti Fog, quick clean of my specs each morning works perfectly. With the pin lock I never need to lift my visor, even when the temp is well below zero.

I get about three to four years from my pinlocks in a Shoei.