straightening handlebar
straightening handlebar
Author
Discussion

boyse7en

Original Poster:

8,237 posts

196 months

Thursday 28th September 2017
quotequote all
My BMW F800S tipped over the other day while stationary and landed on its side. Only damage is a broken indicator lens and a lightly bent handlebar/clip-on. It's still rideable, but feels slightly "off"

Any tips on how best to straighten it? I've tried buying a replacement but they don't seem to be available

MotorsportTom

3,343 posts

192 months

Thursday 28th September 2017
quotequote all
eBay is a good place to look (sorry fi you already have)

To straighten it is a risk but if it were me I'd take it off the bike, clamp the turned 90 degrees in a vice, so it's held relatively flat. Then big bar with similar internal diameter to the external diameter of the clip on.

Then lot's of heat with a blow torch and tweak away until straight. Depends what it is made of but there is the potential to stress fracture and therefore weaken the clip on.

Unless they are £100 to buy I'd always recommend buying another as it's just such a faff.

hman

7,497 posts

225 months

Thursday 28th September 2017
quotequote all
I wouldn't try to straighten it if its made of alloy - buying a new one would be a much better idea

boyse7en

Original Poster:

8,237 posts

196 months

Thursday 28th September 2017
quotequote all
MotorsportTom said:
eBay is a good place to look (sorry fi you already have)

To straighten it is a risk but if it were me I'd take it off the bike, clamp the turned 90 degrees in a vice, so it's held relatively flat. Then big bar with similar internal diameter to the external diameter of the clip on.

Then lot's of heat with a blow torch and tweak away until straight. Depends what it is made of but there is the potential to stress fracture and therefore weaken the clip on.

Unless they are £100 to buy I'd always recommend buying another as it's just such a faff.
Nothing on eBay (apart from one in the USA...which is described as "slightly bent" rolleyes), Motorworks don't have any used ones. A new one is £160, which is a bit salty for a bike worth about £1500

MrAverage

844 posts

158 months

Thursday 28th September 2017
quotequote all
Give these a call: 01708 863500 1st moto solutions.

the bloke has so much stuff he cant list it all on ebay. seems to have almost everything ive needed in the past

Wacky Racer

41,412 posts

278 months

Thursday 28th September 2017
quotequote all
boyse7en said:
. A new one is £160, which is a bit salty for a bike worth about £1500
I appreciate this but, how much is your life worth if it snaps at 70mph?

Also will it pass an MOT as it is?

Otherwise just soldier on and keep your eyes on breakers websites.

underwhelmist

2,053 posts

165 months

Thursday 28th September 2017
quotequote all
Wacky Racer said:
Also will it pass an MOT as it is?
Mine failed its MOT last year for a *very* slightly bent bar. I was lucky though, got a replacement for a tenner off ebay.

boyse7en

Original Poster:

8,237 posts

196 months

Monday 2nd October 2017
quotequote all
Took it off over the weekend and discovered it is steel, not alloy.

Stuck it in a vice and bent it back straight using a big pipe slid over it. It wasn't very bent at all, maybe about 5-10mm difference at the far end and no signs of any kinking.

hman

7,497 posts

225 months

Monday 2nd October 2017
quotequote all
Being steel is probably why it bent in the first place - alloy normally cracks along the bend or snaps.

Steel is ok for minor straightening IMO