Sharp brakes
Author
Discussion

CaptainSlow

Original Poster:

13,179 posts

243 months

Wednesday 1st November 2017
quotequote all
At the weekend I gave the front brakes a good clean, pads out...pistons out a bit and a good going over with cleaner and tooth brush plus some new shiny caliper pins. I also changed the fluid.

Now the brakes are incredibly sharp with the smallest amount of pressure (no abs). Is there any way to back things off a little?

Prof Prolapse

16,163 posts

221 months

Wednesday 1st November 2017
quotequote all
Add water to your fluid until you find a level of sponge you're happy with.


mckeann

2,996 posts

260 months

Wednesday 1st November 2017
quotequote all
Put one pad in backwards to reduce braking by 25%. Much more accurate than fiddling with brake fluid.

patchb

1,004 posts

145 months

Wednesday 1st November 2017
quotequote all
I find soaking the pads in engine oil overnight reduces initial bite somewhat...



You'll get used to it

black-k1

12,811 posts

260 months

Thursday 2nd November 2017
quotequote all
Don't squeeze the lever so hard or so abruptly?


Jazoli

9,705 posts

281 months

Thursday 2nd November 2017
quotequote all
Surely the easiest way is to spray your discs with WD40?

Or just fit Goldfren pads hehe

Mr2Mike

20,143 posts

286 months

Thursday 2nd November 2017
quotequote all
CaptainSlow said:
At the weekend I gave the front brakes a good clean, pads out...pistons out a bit and a good going over with cleaner and tooth brush plus some new shiny caliper pins. I also changed the fluid.

Now the brakes are incredibly sharp with the smallest amount of pressure (no abs). Is there any way to back things off a little?
Buy some knackered old calipers from eBay and you'll be back to needing two hands again in no time.

Fleegle

16,710 posts

207 months

Thursday 2nd November 2017
quotequote all
Inject some air bubbles into the caliper, or loosen the banjo bolt

Biker's Nemesis

41,486 posts

239 months

Thursday 2nd November 2017
quotequote all
Use your feet?

Rubin215

4,201 posts

187 months

Thursday 2nd November 2017
quotequote all
What compound are the pads?

If they're organic I would suggest olive oil instead of WD-40...

Mr2Mike

20,143 posts

286 months

Thursday 2nd November 2017
quotequote all
Rubin215 said:
What compound are the pads?

If they're organic I would suggest olive oil instead of WD-40...
Virgin? Also what type of olive oil?

Deranged Granny

2,323 posts

199 months

Thursday 2nd November 2017
quotequote all
Fit Chinese levers

CaptainSlow

Original Poster:

13,179 posts

243 months

Thursday 2nd November 2017
quotequote all
Thanks for the help. Quickest and easiest solution was to open up the bleed nipples a bit.

Jazoli

9,705 posts

281 months

Thursday 2nd November 2017
quotequote all
CaptainSlow said:
Thanks for the help. Quickest and easiest solution was to open up the bleed nipples a bit.
Seriously????

rev-erend

21,624 posts

315 months

Thursday 2nd November 2017
quotequote all
Fit some old knackered rubber hoses rather that aeroquip lines.

mckeann

2,996 posts

260 months

Thursday 2nd November 2017
quotequote all
Once you cracked them, just leave one a little open,

sc0tt

18,310 posts

232 months

Thursday 2nd November 2017
quotequote all
Remove your brake lever,

CaptainSlow

Original Poster:

13,179 posts

243 months

Thursday 2nd November 2017
quotequote all
Jazoli said:
CaptainSlow said:
Thanks for the help. Quickest and easiest solution was to open up the bleed nipples a bit.
Seriously????
No

Gavia

7,627 posts

122 months

Thursday 2nd November 2017
quotequote all
Fit some from a new R1, apparently they’re st

twizellb

2,786 posts

243 months

Thursday 2nd November 2017
quotequote all
Gavia said:
Fit some from a new R1, apparently they’re st
I was going to say the same as i read down the page but you beat me too it Si laugh