2006 Vantage Dipped beam bulb failure
2006 Vantage Dipped beam bulb failure
Author
Discussion

leerandle

Original Poster:

834 posts

138 months

Saturday 16th December 2017
quotequote all
Does anyone know what type of bulb is need and whether it’s an OEM part only ? Been quoted about £80 from AM, which I’m happy to pay if that’s the going rate. It’s the dipped light, not the LED strip down the side.

V8V Pete

2,536 posts

157 months

Saturday 16th December 2017
quotequote all
Have you checked to see if there's one in the cubby hole under the rear parcel shelf Lee?

leerandle

Original Poster:

834 posts

138 months

Saturday 16th December 2017
quotequote all
Of course not Pete.........I’ll check later lol.

Did I see you at the McGurks meet last week ? Think I saw you, but didn’t get chance to chat.

V8V Pete

2,536 posts

157 months

Saturday 16th December 2017
quotequote all
Yes, I was there Lee. I saw your car but missed you. Rockingham in April?

AndyNW

12 posts

183 months

Sunday 17th December 2017
quotequote all
Hi, have you made progress here? I have had the same problem on my 07 Vantage. I bought 2 replacement HID bulbs on ebay last week for £12.99. Replacement was quite easy, I just had to take the front wheel off to get at the access panel. They arrived quickly but sadly I still have the problem. I put the old, supposedly faulty, bulb in the good side and it works fine so now I'm wondering where the problem is. There is a failure message on the instruments and, of course the dip beam isn't working.
Any ideas welcome. The failure came after I'd allowed the battery to run down which caused the usual multiple spurious fault messages plus failure of mirror auto-fold and side-window drop. I can reset the windows but I understand I have to get the service centre to sort the autofold.

My current thinking is that the problem is with the ballast, if only I can find it. Maybe it's behind the wheel arch liner?

Following a call to Wilmslow today, Monday, I now believe the ballast is below the light unit behind the wheel arch liner. It looks like the task is to remove the liner having firstly removed the undertray. 20+ Torx screws to get out! I've booked it into my friendly garage with a car lift.

Edited by AndyNW on Sunday 17th December 16:35


Edited by AndyNW on Monday 18th December 20:49

leerandle

Original Poster:

834 posts

138 months

Sunday 17th December 2017
quotequote all
No progress yet, I’m currently away for the weekend. I’ll have a look next week and let you know how I get on.

leerandle

Original Poster:

834 posts

138 months

Monday 18th December 2017
quotequote all
AndyNW said:
Hi, have you made progress here? I have had the same problem on my 07 Vantage. I bought 2 replacement HID bulbs on ebay last week for £12.99. Replacement was quite easy, I just had to take the front wheel off to get at the access panel. They arrived quickly but sadly I still have the problem. I put the old, supposedly faulty, bulb in the good side and it works fine so now I'm wondering where the problem is. There is a failure message on the instruments and, of course the dip beam isn't working.
Any ideas welcome. The failure came after I'd allowed the battery to run down which caused the usual multiple spurious fault messages plus failure of mirror auto-fold and side-window drop. I can reset the windows but I understand I have to get the service centre to sort it.
My current thinking is that the problem is with the ballast, if only I can find it. Maybe it's behind the wheel arch liner?

Edited by AndyNW on Sunday 17th December 16:35
Can you let me know what part numbers your ordered ?

AndyNW

12 posts

183 months

Thursday 28th December 2017
quotequote all
Nothing ordered as yet, but I believe the ballast is:-
4G43-13C169-AA, or possibly AB.
If you google that number it comes up as a part for AMs. Prices seem to vary upwards of £70 used, to maybe £180. Presumably much more from a main dealers. I'm waiting till after the holiday to get into the wheel arch and confirm the identity of the unit. And to also see if there is an alternative, i.e. cheaper, part.

leerandle

Original Poster:

834 posts

138 months

Thursday 28th December 2017
quotequote all
I managed to get a couple of bulbs off Ebay, x2 for £45 (Philips D1S 4300K 35W Xenons).

Still awaiting to get them delivered.

I will swap both even though only x1 is not working so the brightness will be the same on both sides.

I'll try fitting these first, if I still have a problem, then will try and have a look at the ballast (I always try and fix the cheapest part first)


8Tech

2,221 posts

229 months

Thursday 28th December 2017
quotequote all
Have you checked the fuse?

leerandle

Original Poster:

834 posts

138 months

Friday 29th December 2017
quotequote all
8Tech said:
Have you checked the fuse?
I assumed they ran off (left and right) the same fuse and as only one has gone, thought it can’t be fuse.

AndyNW

12 posts

183 months

Friday 29th December 2017
quotequote all
There are two fuses in the passenger footwell, left headlamp, right headlamp from the owner's handbook. That suggests both main beam and dip are controlled from the same fuse, but it doesn't seem to work like that if you remove one of the fuses.

I agree with your logic of doing the cheaper one first, I just hope it works out for you.

AndyNW

12 posts

183 months

Thursday 4th January 2018
quotequote all
For anyone interested in this topic the key part number for the ballast seems to be XLD 145. eBay gives lots of hits and indicates that the part is on several other cars, e.g. Land Rover. Prices seem to start at about £20 with long delivery times from China or £40 with a couple days delivery within the UK. Plenty of much higher prices too.
The unit is screwed to the underside of the headlamp unit. Removal required partial removal of the wheel arch liner. Complete removal of the liner might have made it easier. The head lamp access panel isn't big enough but removal of that probably makes the liner more flexible, giving more room to access the ballast unit. I also had to partially remove the air filter box, i.e. lower it by an inch or two, to get access to one of the three screws. These screws require a 5.5 mm socket. The air filter box is held in by 3x8mm bolts. I would suggest undoing the hard-to-get-at 5.5mm screw first, and trying really hard to do it without lowering the air filter box. For me 2 of the air filter box screws had seized and so sheared at quite light torque, meaning that they had to be drilled out. This required a car lift and removal of the the undertray and front skid/splitter.
At the end of all that the headlamps are now working but I still have the bulb failure error message on the display, so I guess I'll still have to go to a dealers to reset it. [correction: the failure message has reset itself - perhaps it just needed a few minutes with the headlamps on?]

There are a few useful videos on You Tube about working in this area.

A final word, caution high voltages in the ballast unit. I guess if you poke around in the plug areas.

Edited by AndyNW on Wednesday 10th January 17:14


Edited by AndyNW on Thursday 11th January 17:44

huntsen

137 posts

124 months

Wednesday 30th May 2018
quotequote all
AndyNW said:
The unit is screwed to the underside of the headlamp unit. Removal required partial removal of the wheel arch liner. Complete removal of the liner might have made it easier. The head lamp access panel isn't big enough but removal of that probably makes the liner more flexible, giving more room to access the ballast unit. I also had to partially remove the air filter box, i.e. lower it by an inch or two, to get access to one of the three screws. These screws require a 5.5 mm socket. The air filter box is held in by 3x8mm bolts. I would suggest undoing the hard-to-get-at 5.5mm screw first, and trying really hard to do it without lowering the air filter box.
A final word, caution high voltages in the ballast unit. I guess if you poke around in the plug areas.
I've just replaced the ballast for the offside dipped beam in my 2007 V8 Vantage.
Go straight for complete removal of the wheel arch liner. This allows you to reattach the deadening foam-filled bags that are held on with (now dead) double-sided tape. It also allows greasing of the many bolts and self-tapping screws that hold the liner and front splitter assembly in place. It looks awesome, but reassembly afterwards is much easier.
Avoid moving the air filter box if at all possible; the 5.5mm screws can just be accessed with a small socket.
The first time you see the headlamp light up and self-level is reward in itself!