Do carbon ceramic brakes make a noise at low speed
Discussion
Not sure if this is normal or not. I have a 2013 DB9 with ceramic brakes and when braking at low speeds I can hear a noise. Hard to describe but its like a whirring ish type sound. Anybody else notice this noise, not sure if it's normal or not for ceramics. Checked my pads and there appears to be plenty of life in them. No noises audible at speeds above 15 mph or so.
Regards
Regards
RS6bird said:
Yes, very normal. Not sure the exact year the CCBs went from gen 1 to gen 2, but that also improved things significantly. Please see my thread on my recent change of discs on my V12V. You can tell the generation of the disc by their part number.
I believe it to be for the 2013MY face lift db9.The Virarge talks about Gen1 and then the 2013 MY DB9 is the later CCB /CCM but not sure if that's Gen 2 or Gen 3 see some conflicting info on this. But it should not be Gen 1 brakes anyway.
Here is a link to my old thread:
https://www.pistonheads.com/gassing/topic.asp?h=0&...
On the V12V, there were only Gen 1 and Gen 2 discs that I am aware. I recently changed them to the current ones being used in the latest V12VS. The part numbers are on my thread, and the initial number sequence should be the same for the Vantage and the V12V.
https://www.pistonheads.com/gassing/topic.asp?h=0&...
On the V12V, there were only Gen 1 and Gen 2 discs that I am aware. I recently changed them to the current ones being used in the latest V12VS. The part numbers are on my thread, and the initial number sequence should be the same for the Vantage and the V12V.
Just an update on this, my car went in for some work recently. I was notified at this time that my front brake pads were worn out. Even though it appears there is still material left on the pads, the supporting pins were exposed and rubbing against the disc. Worryingly the low pad warning light was not illuminated either. Anyway continuing with the pads would jeopardize my discs as the pins had started marking the discs. Not wanting to risk my discs the pads were replaced straight away (at an expected eye watering cost). I can state I no longer have any noise at low speed now. There is nothing at all, so not sure what was going on before.
Just be wary if you have ceramic brakes the pads may need replacing sooner than you think.
Just be wary if you have ceramic brakes the pads may need replacing sooner than you think.
AdamV12V said:
I thought the pads were only about £600-£700 or so for a set? How much did you get charged if you don't mind me asking?
Yeah, that used to be about the price, but Aston parts prices generally are continually on the rise, some parts are becoming eye watering, so a constant check to see latest price update for any part is always needed these days. List price for pads (exc vat) is now £731.64, + about an hour / hour and half labour to install and bed-in so in region of £875-£950 seems fair enough depending on if at indie or franchised (don’t forget CCM calipers need removing from upright to fit the pad whereas to change pads on steel brakes is simple pin removal keeping calliper on upright meaning not much labour).
I’ve seen plenty of cases of what’s being described here, where the mounting pins wear through the pad yet the wear lead indicator is not flashing alarm bells on dashboard. The tell tale sign without stripping calliper to look at pads directly is to look out for scoring witness marks on the disc.
The pads in the pic didn’t ping the wear light. The pad area where the wear indicator sits is fine, the leading edges of the pad are worn lower.
One of the pads can be argued that the wear indicator didn’t ping because corrosion has crumbled the pad material away and that is the reason for the exposed pin. However the other pad shows worn surface without any corrosion crumbling and the pin is exposed and wearing on the disc without a wear light ping. Design fault?
Re the previous post detailing mounting pin breakthrough but no illumination of wear indicator light on dashboard concerning the front pads, here is rear pad status
New pad thickness = 9.5mm
Bronze pin breakthrough = @ 5mm
But
Wear light illumination = @ 3mm
From pics: whilst the pad thickness on rear pads when the pins breakthrough looks meaty, the pad is actually on wear limit 2mm before light comes on at 5mm thickness. That 2mm usage equates to a fair chunk of mileage scrubbing bronze pins on disc. Design fault? User beware!


New pad thickness = 9.5mm
Bronze pin breakthrough = @ 5mm
But
Wear light illumination = @ 3mm
From pics: whilst the pad thickness on rear pads when the pins breakthrough looks meaty, the pad is actually on wear limit 2mm before light comes on at 5mm thickness. That 2mm usage equates to a fair chunk of mileage scrubbing bronze pins on disc. Design fault? User beware!
BamfordMike said:
Re the previous post detailing mounting pin breakthrough but no illumination of wear indicator light on dashboard concerning the front pads, here is rear pad status
New pad thickness = 9.5mm
Bronze pin breakthrough = @ 5mm
But
Wear light illumination = @ 3mm
From pics: whilst the pad thickness on rear pads when the pins breakthrough looks meaty, the pad is actually on wear limit 2mm before light comes on at 5mm thickness. That 2mm usage equates to a fair chunk of mileage scrubbing bronze pins on disc. Design fault? User beware!


Well done Mike, thanks for spotting that, I'm glad you know what you're looking for!!New pad thickness = 9.5mm
Bronze pin breakthrough = @ 5mm
But
Wear light illumination = @ 3mm
From pics: whilst the pad thickness on rear pads when the pins breakthrough looks meaty, the pad is actually on wear limit 2mm before light comes on at 5mm thickness. That 2mm usage equates to a fair chunk of mileage scrubbing bronze pins on disc. Design fault? User beware!
Yet again you've saved me (more than) a few quid!
Edited by JaseB on Tuesday 22 May 11:13
Gassing Station | Aston Martin | Top of Page | What's New | My Stuff




ked, get new ones in now!