Rear light turn signal not working
Discussion
does anyone have the wiring schematics for the rear tail light? I would like to trace the issue and put some voltage on the connector.
I drove the car today for the first time in months and this was not a good way to start.
If it is dead, does anyone have a single Passenger / Right (US) side rear light they are looking to part with?
I drove the car today for the first time in months and this was not a good way to start.
If it is dead, does anyone have a single Passenger / Right (US) side rear light they are looking to part with?
The board is quite complex for the taillights - I tried for quite a while to figure out what was wrong with mine. In some cases, you may find a blown up FET that you can identify by cracking, and replace. All the parts were intact on mine, and I have no idea where the failure occurred. I did see that that surprisingly, there is no conformal coating on the board - that alone would have probably saved the light even if it gets condensation.
I've ended up creating my own replacement board for the rear lights. Still a work in process unfortunately - it still sets off the check brake light warning, and I haven't figured out how to get the running light go brighter when the brake light goes on (as a short term fix, I have it set so the running light is the inner section, and outer section is the brake - it works, but not as it's supposed to.
I've posted about my project on 6speed - my user name there is HSM precision - I have more images of the factory board there.
Here is an image of the first iteration of the board - no installed images unfortunately - just happy to be able to use my car again
Matt

I've ended up creating my own replacement board for the rear lights. Still a work in process unfortunately - it still sets off the check brake light warning, and I haven't figured out how to get the running light go brighter when the brake light goes on (as a short term fix, I have it set so the running light is the inner section, and outer section is the brake - it works, but not as it's supposed to.
I've posted about my project on 6speed - my user name there is HSM precision - I have more images of the factory board there.
Here is an image of the first iteration of the board - no installed images unfortunately - just happy to be able to use my car again

Matt
messar said:
The board is quite complex for the taillights - I tried for quite a while to figure out what was wrong with mine. In some cases, you may find a blown up FET that you can identify by cracking, and replace. All the parts were intact on mine, and I have no idea where the failure occurred. I did see that that surprisingly, there is no conformal coating on the board - that alone would have probably saved the light even if it gets condensation.
I've ended up creating my own replacement board for the rear lights. Still a work in process unfortunately - it still sets off the check brake light warning, and I haven't figured out how to get the running light go brighter when the brake light goes on (as a short term fix, I have it set so the running light is the inner section, and outer section is the brake - it works, but not as it's supposed to.
I've posted about my project on 6speed - my user name there is HSM precision - I have more images of the factory board there.
Here is an image of the first iteration of the board - no installed images unfortunately - just happy to be able to use my car again
Matt

great progress! I have two samples to attempt first as my local tech who specializes in Porsche cars also works on the Aston's in town. There is three I know of. A 4.3 Vantage, a 2009 DBS, and my 2009 Volante. He had two rear indicator lights. one from each. one clear, and one smoked over. I can dissect those and see if I can learn anything. I've ended up creating my own replacement board for the rear lights. Still a work in process unfortunately - it still sets off the check brake light warning, and I haven't figured out how to get the running light go brighter when the brake light goes on (as a short term fix, I have it set so the running light is the inner section, and outer section is the brake - it works, but not as it's supposed to.
I've posted about my project on 6speed - my user name there is HSM precision - I have more images of the factory board there.
Here is an image of the first iteration of the board - no installed images unfortunately - just happy to be able to use my car again

Matt
Gassing Station | Aston Martin | Top of Page | What's New | My Stuff


