New owner niggles question
Discussion
I have been driving my “new” 2011 V8S for a week now - taking it on a 2000 km roadtrip. Very pleased with the the car. Car bought from AM dealership with year warranty so want to make sure I catch all oddities.
3 Things so far
- After washing the car found damp in rear lights
- breaks squeek at low speed
- soft knocking sound while driving at bad roads, assuming rear springs
Seems like things that should be fixed/fixable but appreciate your feedback
Thanks!
3 Things so far
- After washing the car found damp in rear lights
- breaks squeek at low speed
- soft knocking sound while driving at bad roads, assuming rear springs
Seems like things that should be fixed/fixable but appreciate your feedback
Thanks!
These are common:
- After washing the car found damp in rear lights
- breaks squeek at low speed
The condensation in your tail lamps is something you'll want to remedy before it ruins the lamps. Factory-recommended solution is to drill a hole in the housing and blow air into the lamp to get the water out.
Brake squeal is caused by a few things:
1) Pads need to be bedded in
2) Need anti-squeal grease on the backing plates (the factory offers shims that can help).
3) Front pads aren't chamfered, so material can get built up on their leading edges, which causes squeal.
Tons of documentation on all of this if you search around a bit.
The rear suspension could be a few things. Might be the struts are worn out or are wearing out (look for signs of leaking). Control arm bushings may be another thing to look at.
- After washing the car found damp in rear lights
- breaks squeek at low speed
The condensation in your tail lamps is something you'll want to remedy before it ruins the lamps. Factory-recommended solution is to drill a hole in the housing and blow air into the lamp to get the water out.
Brake squeal is caused by a few things:
1) Pads need to be bedded in
2) Need anti-squeal grease on the backing plates (the factory offers shims that can help).
3) Front pads aren't chamfered, so material can get built up on their leading edges, which causes squeal.
Tons of documentation on all of this if you search around a bit.
The rear suspension could be a few things. Might be the struts are worn out or are wearing out (look for signs of leaking). Control arm bushings may be another thing to look at.
JB65 said:
Thanks for the help. Had another good listening session and sound from the rear springs is more a squeaky sound rather than a knock that synchronises with the bumps in the road. Maybe just spring lubrication? Any additional thoughts appreciated!
Is it temperature dependent? If so, it may be a deformed donut seal between the exhaust mid section and the back box. Mine did this. Main dealer said it was the exhaust valves and would need a new back box to solve. I thought BS. Bamford Rose diagnosed it as the donut and fixed it for a few pounds. Awesome 
1) Get the misted tear light unit changed under the AM warranty at no additional cost. I would only look to fix myself out of warranty (some great experience of that on here).
2) The break squeak is part of the nature of this and other similar sports cars. It’s even stated in the owner’s handbook. I use my 2014 V8V regularly (at least one good drive each week, over winter too) and the squeaking comes and goes. I’ve heard worse
3) I assume you’ve found the rear noise isn’t from the rear hatch? Mine squeaked over rough surfaces. Mentioned it at my last service with AM Bristol and they did some magic to fix it which was really appreciated as I live in the country and have to cross the border to Wales for smooth black top.
2) The break squeak is part of the nature of this and other similar sports cars. It’s even stated in the owner’s handbook. I use my 2014 V8V regularly (at least one good drive each week, over winter too) and the squeaking comes and goes. I’ve heard worse

3) I assume you’ve found the rear noise isn’t from the rear hatch? Mine squeaked over rough surfaces. Mentioned it at my last service with AM Bristol and they did some magic to fix it which was really appreciated as I live in the country and have to cross the border to Wales for smooth black top.
PatCub said:
The reason the rear lights leak is because of the poor seal between the two halves, the seal is a piece of double sided tape.
Heat the lens in the oven at a low temp. Pull the two halfs apart, dry lens out, remove the black double sided tape and reseal with a silicone sealer.

Nooooo, do not use silicone it makes one hell of a mess. My updated guide is here:Heat the lens in the oven at a low temp. Pull the two halfs apart, dry lens out, remove the black double sided tape and reseal with a silicone sealer.
https://www.pistonheads.com/gassing/topic.asp?h=0&...
Edited by dbs2000 on Tuesday 8th May 08:16
dbs2000 said:
Nooooo, do not use silicone it makes one hell of a mess. My updated guide is here:
https://www.pistonheads.com/gassing/topic.asp?h=0&...
I stand corrected, thank you and well done on finding a descent sealing material.https://www.pistonheads.com/gassing/topic.asp?h=0&...
Edited by dbs2000 on Tuesday 8th May 08:16
How well does it squash in the joint?
Pretty well, it's OEM stuff. I wrote the original guide and used silicone as you previously suggested and it does do the job but I found it went everywhere.
I found this stuff by looking at the OE process and speaking to a few US tuners that customise customer lights. You need to roll it out and I found pre-heating the cover always helps. Here's a good guide:
https://www.youtube.com/watch?v=duFXYRt_nD0
I found this stuff by looking at the OE process and speaking to a few US tuners that customise customer lights. You need to roll it out and I found pre-heating the cover always helps. Here's a good guide:
https://www.youtube.com/watch?v=duFXYRt_nD0
Edited by dbs2000 on Tuesday 8th May 12:05
Gassing Station | Aston Martin | Top of Page | What's New | My Stuff


