Home network planning help
Author
Discussion

Maxf

Original Poster:

8,444 posts

272 months

Friday 10th August 2018
quotequote all


Ive got the builders in at the moment and the floors are up, so I've ordered 300m of cat6a cable to put a simple home network together. I'm no IT guy, so bear with me if some of my thoughts/questions are rather basic.

Basic plan is:

1 run into kitchen
2 runs into dining room
4 runs into study
4 runs into lounge
4 runs into the loft which can be dropped into bedrooms as they are redecorated over time.

I'm confident that is enough for our needs. At my last place we had fewer cable runs and didnt use them all even then.

However, I'm not sure where to put the switch/bulk of the cables - options are: cupboard under the stairs, garage, dining room, or possibly the hallway. I am going to site the router and wi-fi in the same place obviously. Cupboard under the stairs is a bit too cramped, but the garage might work.

Also, what do I actually need to buy? I was originally just going to buy a switch to site out of the way near the router and a load of faceplates, but looking around this morning I've seen this kind of thing...

https://www.cablemonkey.co.uk/soho-cabinets/9509-1...

with

https://www.cablemonkey.co.uk/10-patch-panels/9512...

Is the idea just that this keeps it all tidy? Does the patch panel act as a switch or is it just an alternative to a load of face plates (I'm assuming the latter)? So, assuming I'll still need a switch, how do I ensure it fits into the box; is 10u a sizing convention?

Apologies for the dumb questions - I'm a little out of my depth, but definitely want to add the cables, so need to try and do it properly!






Crumpet

5,513 posts

211 months

Friday 10th August 2018
quotequote all
I’m currently in the process of doing mine and learning as I go along but one thing I would maybe add is data and power to the loft for CCTV and then maybe four to eight cables run to sensible locations around the house where you may wish to add a camera in future.


Maxf

Original Poster:

8,444 posts

272 months

Friday 10th August 2018
quotequote all
Good idea! Once I understand the basics a bit better I can run the cables easily enough - I dont want to end up with it all terminating in the wrong place though!

Mr Pointy

13,447 posts

190 months

Friday 10th August 2018
quotequote all
If you can I'd suggest the garage as your central point. House everything in a cabinet like these:

https://www.comms-express.com/categories/390mm-dee...

the useable height is measured in U, which is 1.75". A patch panel is 1U so decide how much kit you want to fit & don't skimp. Bolt it to the wall high up out of the way. Sit your internet modem/router on a shelf & you'll need to get power & the incoming internet line to it. You can get switches with mouting ears to bolt into the cabinet or sit one on another shelf. Then you use short patchcords to connect between your switch & the patch panel points as required.

The patch panel is the termination point for your cables - the other end in the rooms is on faceplates as you describe. I'd suggest one that takes keystone jacks (individual connectors) rather than one that has a long strip of punchdowns on the back. You've got more chance of making a decent temination with a tooless keystone connector

https://www.comms-express.com/products/excel-24-po...
https://www.comms-express.com/products/excel-cat6-...

If the router is in the garage you might want to add some Wireless Access Points in the loft so add cables as necessary.

All this is a bit OTT for home use but it's the neatest way. Is CAT6e really necessary? It isn't going to get you any more performance over CAT5e for Ethernet connections & it's more difficult to run & make off.

crmcatee

5,808 posts

258 months

Friday 10th August 2018
quotequote all
If you're running one cable to each location - run two. The single faceplate can handle two and guaranteed at some stage along the line you'll be thankful you did. Costs peanuts. If you think you'll need two, put in four.

Stick the wiring in the garage, where the switch would also be - oh and any network drives so make sure you provide enough power outlets..

The router will provide the wifi so put that in the middle of the house and make sure you've got at least one connection from the router to where the wiring will terminate.

You will also need to provide wiring from the PTT (e.g. BT) entry point/jack to wherever you're going to put the router so the adsl service can reach the router.



I'd say the cabinet was overkill unless you have a messy garage. Something like this would suffice -
https://www.cablemonkey.co.uk/patching-brackets-fr...



Gary C

15,378 posts

210 months

Friday 10th August 2018
quotequote all
Some sound stuff. Especially about lots of cables, put in as many as will fit smile

The Wi-Fi hub doesn't have to be your router. I would use something as a router such as your vdsl modem (or as I do a separate vdsl modem and router) then a multiport switch to connect your incoming cables then a Wi-Fi AP plugged in at a convenient location.

Not having everything on Wi-Fi is wonderful

Maxf

Original Poster:

8,444 posts

272 months

Friday 10th August 2018
quotequote all
Mr Pointy said:
If you can I'd suggest the garage as your central point. House everything in a cabinet like these:

https://www.comms-express.com/categories/390mm-dee...

the useable height is measured in U, which is 1.75". A patch panel is 1U so decide how much kit you want to fit & don't skimp. Bolt it to the wall high up out of the way. Sit your internet modem/router on a shelf & you'll need to get power & the incoming internet line to it. You can get switches with mouting ears to bolt into the cabinet or sit one on another shelf. Then you use short patchcords to connect between your switch & the patch panel points as required.

The patch panel is the termination point for your cables - the other end in the rooms is on faceplates as you describe. I'd suggest one that takes keystone jacks (individual connectors) rather than one that has a long strip of punchdowns on the back. You've got more chance of making a decent temination with a tooless keystone connector

https://www.comms-express.com/products/excel-24-po...
https://www.comms-express.com/products/excel-cat6-...

If the router is in the garage you might want to add some Wireless Access Points in the loft so add cables as necessary.

All this is a bit OTT for home use but it's the neatest way. Is CAT6e really necessary? It isn't going to get you any more performance over CAT5e for Ethernet connections & it's more difficult to run & make off.
Many thanks - that's really helpful!

I went for cat6 as I was told that will support 4k video better and the price difference wasnt huge.

I'll look at the garage tonight and see where I could site it all





megaphone

11,723 posts

282 months

Friday 10th August 2018
quotequote all
CAT6a is a PITA to terminate properly, it does not bend well, big and chunky. Unless you're sending 4k, I'd stick with CAT5e.

TartanPaint

3,367 posts

170 months

Friday 10th August 2018
quotequote all
You want one of these somewhere near the middle of the house.

http://www.broadbandbuyer.com/store/wifi-access-po...

Ours is on the upstairs landing ceiling (sort of middle of the house, and easy access from the loft above).

Power is by its own PoE adapter, so all you need is another run of Cat5e (don't waste Cat6) to where you think it might get mounted.


Mr Pointy

13,447 posts

190 months

Friday 10th August 2018
quotequote all
Maxf said:
I went for cat6 as I was told that will support 4k video better and the price difference wasnt huge.
Just to be clear that if you are talking about streaming or tramsferring 4K video as files (ie Ethernet/iP traffic) then CAT6a is no different to CAT5e: they will both carry Gigabit traffic, which is the limit of the network ports on all of your equipment anyway. If you are talking about using the cabling to transfer video via something like HDBaseT then apparantly CAT6a cabling can make a difference. However, you'll have to be careful all of the components (plugs, sockets, cable etc) are compatible & you need to install & make off the cabling very carefully to reach the CAT6a specifcation. Since you've already bought the cable it's moot point but as has been said CAT6e cable can be a bit of a sod to work with in a domestic ebvironment. I'd suggest you use tooless keystone jacks in the faceplates as well as the patch panels as they are much easier to make off accurately. Just be aware of the depth of the back boxes.

megaphone

11,723 posts

282 months

Friday 10th August 2018
quotequote all
OP please clarify, are you buying CAT6a or standard CAT6? There is a difference. You have mentioned both.

anonymous-user

85 months

Friday 10th August 2018
quotequote all
If using patch panel go for the ones that take the RJ45 keystones rather than the ones with integrated punch downs. The keystones are much more reliable, I went for the cheap option and had a lot of trouble with unreliable connections so binned it.

Also get a decent punchdown tool, connection tester and pick one TIA 568 wiring connection scheme and stick to it religiously.

Gary C

15,378 posts

210 months

Saturday 11th August 2018
quotequote all
megaphone said:
CAT6a is a PITA to terminate properly, it does not bend well, big and chunky. Unless you're sending 4k, I'd stick with CAT5e.
Cat6 though is fine and easy to terminate. And in theory can run 10G on a run of 48 meters or less.

ging84

9,548 posts

177 months

Saturday 11th August 2018
quotequote all
that cabinet seems completely unsuitable
it is 100mm deep, so no room for a switch, to be honest i don't see the point in it, it has a power supplier, but i have no idea what you could fit in it that would need power.
It seems to be for filling with a lot of patch panels so that your wall sockets can be directly patched to sockets in other rooms, which would sort of make sense for things like hdmi over cat5/6 except that these applications are much more sensitive, so the extra length and connectors required going via a comms cabinet seems like it could be quite limiting.


When you say
"I am going to site the router and wi-fi in the same place obviously"
Why? Is there some perceived technical advantage to it? or is it about convenience? Because personally I like to have a patch panel and switch tucked away in a cupboard somewhere they can be setup and forgotten about, but the router somewhere much more accessible because it is hardly uncommon for them to need attention.

Order66

6,740 posts

280 months

Saturday 11th August 2018
quotequote all
Do you have a real need for wired at all? A decent mesh wifi with 802.11ac capabilities will easily stream a 4k blu ray (or several simultaneously). Unless you are gaming and need ultra-low latency or transferring large amounts of data between devices internally, then there's not a huge benefit to the hard wired connection. On the other hand if its a standard household with a number of wifi devices looking to be on the net then a mesh wifi would be a lot simpler to install.

I just junked my ubiquiti devices and replaced with a Netgear Orbi setup - couldn't rate it higher.

Gary C

15,378 posts

210 months

Sunday 12th August 2018
quotequote all
Order66 said:
Do you have a real need for wired at all? A decent mesh wifi with 802.11ac capabilities will easily stream a 4k blu ray (or several simultaneously). Unless you are gaming and need ultra-low latency or transferring large amounts of data between devices internally, then there's not a huge benefit to the hard wired connection. On the other hand if its a standard household with a number of wifi devices looking to be on the net then a mesh wifi would be a lot simpler to install.

I just junked my ubiquiti devices and replaced with a Netgear Orbi setup - couldn't rate it higher.
Mesh systems are good no doubt. But for equipment that stays in the same place you cannot beat wired. The only stopper for wired normally is tha difficulty and if you ever have the chance to flood wire a house, do it.

Maxf

Original Poster:

8,444 posts

272 months

Monday 13th August 2018
quotequote all
Thanks again for the input. I've returned the Cat6a and have a roll of cat5e now, which seems like it will be easier to deal with/terminate.

We've opted to run everything to the garage - not loads of runs of cable, but enough for TVs, Consoles, Music etc - pretty much anything which is in a fixed position. I've no massive desire for full CCTV so won't be putting loads of cables in for that this time.

In terms of whether I need it.... probably not - although I hold all of my music collection on a NAS drive which is crazily unreliable over wifi, and never missed a beat when wired. I also see more and more stuff being 'smart' and competing for the wi-fi, so to have the TVs, consoles, printer and music all 'hard wired' seems like a sensible move as the floorboards are up anyway!


megaphone

11,723 posts

282 months

Monday 13th August 2018
quotequote all
As others have said, if it doesn't move then run a cable if you can.

And ditto, run in some cables for proper WiFi access points, ideally these can be ceiling mounted, one on the landing ceiling and another downstairs, in the hall or main lounge, maybe one to the top of a kitchen cabinet, depending on the layout. They can be powered over the ethernet cable (PoE) from the garage.

Bikerjon

2,211 posts

192 months

Monday 13th August 2018
quotequote all
These days I'd say the primary reason for running cable is to connect wireless access points. Even that is becoming less of an issue with mesh, but if you have the opportunity then definitely use cable to install some proper Wi-Fi points as well to the TV and Study. Anything else will probably never get used.

Gary C

15,378 posts

210 months

Tuesday 14th August 2018
quotequote all
Bikerjon said:
These days I'd say the primary reason for running cable is to connect wireless access points. Even that is becoming less of an issue with mesh, but if you have the opportunity then definitely use cable to install some proper Wi-Fi points as well to the TV and Study. Anything else will probably never get used.
Never used ?

We have,2x smart tv, 5x Sonos speakers, a PC, a Mac, one laptop, two ps4's, one Xbox one, sky box, printer/scanner, nas, two AP's,

And if you use sky q or the like, wiring it is superior to wifi and everything you take off wifi, helps that left on wifi.

If I had a new house built or renovated one, I would always flood wire it, no question. It's fairly cheap to do.