Any Linux audio gurus out there?
Discussion
I have an odd issue.
I have written a script that will generate a sine tone using sox (play), which is played into a sound card.
This tone is then read from the sound card using sox and written to a .wav file.
I then run 'sndfile-info' on trhe .wav file to read back the amplitude.
However...
If I switch between a low(ish) frequency back to a high frequency, the initial level read from the high frequency is the same as the low frequency (but the frequency stored in the .wav is correct!).
Running it a second time result sin the correct amplitude.
Here is my (test!) script: (couldn't use code tags because my script has braces in it)
You'll note that I'm reading the amplitude using two different methods (sox -n stat and sndfile-info) because I thought maybe one of them was wrong....
script is run like this: ./test.sh <duration in secs> <frequency>
e.g. ./test.sh 1 1000 (1 second, 1 kHz)
Any ideas??
Thanks in advance.
I have written a script that will generate a sine tone using sox (play), which is played into a sound card.
This tone is then read from the sound card using sox and written to a .wav file.
I then run 'sndfile-info' on trhe .wav file to read back the amplitude.
However...
If I switch between a low(ish) frequency back to a high frequency, the initial level read from the high frequency is the same as the low frequency (but the frequency stored in the .wav is correct!).
Running it a second time result sin the correct amplitude.
Here is my (test!) script: (couldn't use code tags because my script has braces in it)
You'll note that I'm reading the amplitude using two different methods (sox -n stat and sndfile-info) because I thought maybe one of them was wrong....
script is run like this: ./test.sh <duration in secs> <frequency>
e.g. ./test.sh 1 1000 (1 second, 1 kHz)
script said:
#!/bin/bash
outfile=/tmp/output.wav
duration="$1"
toneduration=$(($duration + 1))
freq="$2"
gain="-1"
playback_dev="hw:1,0" # HiFace spdif
record_dev="hw:0,0"
rm -f $datafile $outfile
rm -f ${freq}_fr.wav
AUDIODEV=$playback_dev play --buffer 4194304 -q --norm=-1.1 -b 32 -r 192k -n synth $toneduration sine $freq|sox -q --buffer 4194304 -b 32 -r 192k -c 2 -t alsa $record_dev ${freq}_fr.wav trim 0 $duration
sleep 1
amplitude=$(sox ${freq}_fr.wav -n stat 2>&1 | sed -n 's#^Maximum amplitude:[^0-9]*\([0-9.]*\)$#\1#p')
db=$(echo "scale=3; 20*l($amplitude)/l(10)" | bc -l)
db2=$(sndfile-info ${freq}_fr.wav |grep "Signal Max" |cut -d "(" -f2 | cut -d "d" -f1)
echo $freq, $db, $db2
rm -f $infile $outfile
Sample output:outfile=/tmp/output.wav
duration="$1"
toneduration=$(($duration + 1))
freq="$2"
gain="-1"
playback_dev="hw:1,0" # HiFace spdif
record_dev="hw:0,0"
rm -f $datafile $outfile
rm -f ${freq}_fr.wav
AUDIODEV=$playback_dev play --buffer 4194304 -q --norm=-1.1 -b 32 -r 192k -n synth $toneduration sine $freq|sox -q --buffer 4194304 -b 32 -r 192k -c 2 -t alsa $record_dev ${freq}_fr.wav trim 0 $duration
sleep 1
amplitude=$(sox ${freq}_fr.wav -n stat 2>&1 | sed -n 's#^Maximum amplitude:[^0-9]*\([0-9.]*\)$#\1#p')
db=$(echo "scale=3; 20*l($amplitude)/l(10)" | bc -l)
db2=$(sndfile-info ${freq}_fr.wav |grep "Signal Max" |cut -d "(" -f2 | cut -d "d" -f1)
echo $freq, $db, $db2
rm -f $infile $outfile
./test.sh 1 81920
81920, -17.080, -17.07 <<<<< correct
./test.sh 1 8192
8192, -1.172, -1.17 <<<< correct
./test.sh 1 81920
81920, -1.181, -1.18 <<<< incorrect!
./test.sh 1 81920
81920, -17.072, -17.07 <<<<< correct!
Any ideas??
Thanks in advance.
Is it something to do with the --norm parameter ? That will normalise volume(power), which will result in lower peak-peak amplitude for higher frequencies.
Amplitude has a relationship with frequency when considering volume: http://www.indiana.edu/~emusic/etext/acoustics/cha...
I think the play command uses that iso226 curve when normalising.
Since you are interested in amplitude and not volume just remove the --norm switch. Hopefully you will get what you're expecting.
Amplitude has a relationship with frequency when considering volume: http://www.indiana.edu/~emusic/etext/acoustics/cha...
I think the play command uses that iso226 curve when normalising.
Since you are interested in amplitude and not volume just remove the --norm switch. Hopefully you will get what you're expecting.
Edited by scorp on Wednesday 29th August 10:06
Thanks, I think I solved it by using 'aply' and 'arecord' instead.
I still use Sox to generate the tone (saved to a file) however.
I can seemingly get consistent results now, when switching between frequencies.
I guess that using 'gain -1' instead of '--norm=-1.1' is the solution, however 'play' doesn't seem to support 'gain'
I still use Sox to generate the tone (saved to a file) however.
# generate the source file to playback
sox -q -b 32 -r 192k -c 2 -n $infile synth $duration sine $i gain $gain # where $i is frequency
# play back and record the source file
aplay -q -D $playback_dev $infile|arecord -q -D plughw:0 -f S32_LE -t wav -r 192k -d $duration $outfile
I can seemingly get consistent results now, when switching between frequencies.
I guess that using 'gain -1' instead of '--norm=-1.1' is the solution, however 'play' doesn't seem to support 'gain'
script said:
./calib.sh 1 80000
80000, -15.960, -15.96
./calib.sh 1 80000
80000, -16.038, -15.74
./calib.sh 1 8000
8000, -1.120, -1.13
./calib.sh 1 8000
8000, -1.120, -1.13
./calib.sh 1 80000
80000, -15.960, -15.96
./calib.sh 1 80000
80000, -16.038, -15.89
That seems pretty consistent now - thanks for your help.80000, -15.960, -15.96
./calib.sh 1 80000
80000, -16.038, -15.74
./calib.sh 1 8000
8000, -1.120, -1.13
./calib.sh 1 8000
8000, -1.120, -1.13
./calib.sh 1 80000
80000, -15.960, -15.96
./calib.sh 1 80000
80000, -16.038, -15.89
Gassing Station | Computers, Gadgets & Stuff | Top of Page | What's New | My Stuff


