Netgear N300 range extender help
Discussion
Dear all
I recently switched to this range extender from a BT version as I thought it had failed. The Netgear extender has been working but then this weekend my daughter yelled downstairs that she had no internet. Its worth mentioning that I followed manufacturers instructions when setting up but I did not realise that is should not be located in the area with the weakest signal. The old extender was also located in the same place. Anyhow I have tried and tried to setup the Netgear unit moving it around the house but no luck. I have tried resetting and going back through the whole registering the device again. It has the green power light and the client link led is green when trying to set it up but there is no router link LED. Im not super IT savvy but I get by and I am at my wits end trying to understand what is wrong. By the way my router is a BT home hub 5.
Any help very much appreciated.
I recently switched to this range extender from a BT version as I thought it had failed. The Netgear extender has been working but then this weekend my daughter yelled downstairs that she had no internet. Its worth mentioning that I followed manufacturers instructions when setting up but I did not realise that is should not be located in the area with the weakest signal. The old extender was also located in the same place. Anyhow I have tried and tried to setup the Netgear unit moving it around the house but no luck. I have tried resetting and going back through the whole registering the device again. It has the green power light and the client link led is green when trying to set it up but there is no router link LED. Im not super IT savvy but I get by and I am at my wits end trying to understand what is wrong. By the way my router is a BT home hub 5.
Any help very much appreciated.
Tricky to advise on the interweb.....
You need to link it via the WPS setting (wifi protected set-up). Which means powering it up and switching on in the same room as your router.... when everything is on, press WPS on the Netgear and then WPS on your router. The two devices will then see each other - give it 3 mins or so.
Then you need to get on to the Netgear N300 (by switching to that signal on your laptop). It should be http://routerlogin.net
You can then make whatever settings (passwords etc).
Once that is all done - move the N300 somewhere else in the house.
Have you done all of that?
You need to link it via the WPS setting (wifi protected set-up). Which means powering it up and switching on in the same room as your router.... when everything is on, press WPS on the Netgear and then WPS on your router. The two devices will then see each other - give it 3 mins or so.
Then you need to get on to the Netgear N300 (by switching to that signal on your laptop). It should be http://routerlogin.net
You can then make whatever settings (passwords etc).
Once that is all done - move the N300 somewhere else in the house.
Have you done all of that?
Appreciate the reply thanks
So yes I have done the WPS sync but do you mean I have to connect to the Netgear wifi address to make the setting changes mentioned. I ask this because I cant get internet access when selecting the Netgear_ext address. Or am I being stupid and completely missing your point here.
So yes I have done the WPS sync but do you mean I have to connect to the Netgear wifi address to make the setting changes mentioned. I ask this because I cant get internet access when selecting the Netgear_ext address. Or am I being stupid and completely missing your point here.
I’m not sure if this helps but I too use the BT range extender which simply repeats the routers SSID seamlessly.
I have also tried other Range extenders including the new BT one and Dl Link one. They repeat by creating a new SSID and not repeating the original one.
That means that you have to connect to a different Wi-fi when connecting to the repeater.
Some use the same password as the router but some have their own password too.
After discovering this I went back to using an old BT one as I like the seamless use.
The big advance of the newer versions is that you can use more than one.on the same router.
With the ones that repeat the same SSID you can only reallybuse one because they risk connecting to each other if you use two and neither actually connects to the router!
I have also tried other Range extenders including the new BT one and Dl Link one. They repeat by creating a new SSID and not repeating the original one.
That means that you have to connect to a different Wi-fi when connecting to the repeater.
Some use the same password as the router but some have their own password too.
After discovering this I went back to using an old BT one as I like the seamless use.
The big advance of the newer versions is that you can use more than one.on the same router.
With the ones that repeat the same SSID you can only reallybuse one because they risk connecting to each other if you use two and neither actually connects to the router!
macp said:
Appreciate the reply thanks
So yes I have done the WPS sync but do you mean I have to connect to the Netgear wifi address to make the setting changes mentioned. I ask this because I cant get internet access when selecting the Netgear_ext address. Or am I being stupid and completely missing your point here.
Yes you will need to be on the Netgear's wifi signal to get onto it's admin page.So yes I have done the WPS sync but do you mean I have to connect to the Netgear wifi address to make the setting changes mentioned. I ask this because I cant get internet access when selecting the Netgear_ext address. Or am I being stupid and completely missing your point here.
If your Netgear is putting out a wifi signal but you can't get onto the internet, then it might be that your router is blocking it - can you see if it is being assigned an IP address?
On your phone (when selecting the Netgear wifi) you should be able to see the IP address.... I no longer use range extenders, so am doing this from memory!

What router are you using? What is its IP address? Is it the same as the Netgear one by any chance?
Thanks again
Im now thinking its the BT router (homehub5) as I remembered last week I had to reset it as my PC lost wifi connection. It was fine afterwards and still is but this morning my wife and daughter are telling me their phones are dropping connection and the smart tv in the kitchen (on a TP Link home plug) also refuses to connect.
Im now thinking its the BT router (homehub5) as I remembered last week I had to reset it as my PC lost wifi connection. It was fine afterwards and still is but this morning my wife and daughter are telling me their phones are dropping connection and the smart tv in the kitchen (on a TP Link home plug) also refuses to connect.
macp said:
I was hoping I wouldnt have to change the router its actually been fine for the last two or three years. By the way the extender IP range was the same as the router. I noticed you mentioned that you dont use extenders so what do you use to get a signal to a weak spot ?
I have a fairly large and ancient house and a single router won't reach everywhere.... so I eventually moved to the BT Whole Home mesh system. It works very well. The advantage with mesh is that devices switch to a better signal quickly and seamlessly without hanging on to the weakest signal.Gassing Station | Computers, Gadgets & Stuff | Top of Page | What's New | My Stuff


