Who knows about RAM & motherboard bios settings?
Discussion
Okie dokie, I have a Gigabyte Z97x-gaming 3 motherboard.
I have 16GB of Corsair 2133mhz ram. In the bios settings, the frequency is set to 1333mhz, with timings of 9,9,9,24. My ram is 2133mhz, with timings of 11,11,11,27. So, I enable XMP, which boosts the frequency and timings to those stated on the Corsair tech spec sheet. However, I'm now getting random BSOD.
Nothing is OC'd, and from what I can see i've set ram up correctly.
Any ideas
I have 16GB of Corsair 2133mhz ram. In the bios settings, the frequency is set to 1333mhz, with timings of 9,9,9,24. My ram is 2133mhz, with timings of 11,11,11,27. So, I enable XMP, which boosts the frequency and timings to those stated on the Corsair tech spec sheet. However, I'm now getting random BSOD.
Nothing is OC'd, and from what I can see i've set ram up correctly.
Any ideas
Hi, hope I can help a little. ..
To start with, just because your memory kit states it can run at 2133, it doesnt necessarily mean your mobo's integrated memory controller can handle those speeds.
Your board states anything above 1600mhz requires overclocking.
See
https://www.gigabyte.com/Motherboard/GA-Z97X-Gamin...
Next to the memory profiles, if there is an (oc) next to the number...it means its going to need overclocking. Every speed listed above 1600 has an (oc).
Overclocking will then depend on the quality of the IMC (integrated memory controller) and ram quality.
I would turn off xmp and start by attempting to set it at 1600mhz.
If this works, then look at the voltage which the memory requires, and look at what voltage the mobo supplies when you try and 'overclock' the memory.
Hope this helps, getting ram running right can be a nightmare and a constant source of issues when overclocking etc..
As an example, i had an old ddr2 set of corsair vengeance memory which needed 2.1v to run at the 'stated' speed stamped on the memory. The mobo would run it at a slower speed as standard, but wouldnt boot if i tried to run it at the stated 1600mhz or whatever it was. I upped the voltage to 2.1 and it worked. However be V V careful with voltages as even 1.5v seems extremely high for some memory these days....stick to no more than what the manufacturer recommends.
Cheers!!
To start with, just because your memory kit states it can run at 2133, it doesnt necessarily mean your mobo's integrated memory controller can handle those speeds.
Your board states anything above 1600mhz requires overclocking.
See
https://www.gigabyte.com/Motherboard/GA-Z97X-Gamin...
Next to the memory profiles, if there is an (oc) next to the number...it means its going to need overclocking. Every speed listed above 1600 has an (oc).
Overclocking will then depend on the quality of the IMC (integrated memory controller) and ram quality.
I would turn off xmp and start by attempting to set it at 1600mhz.
If this works, then look at the voltage which the memory requires, and look at what voltage the mobo supplies when you try and 'overclock' the memory.
Hope this helps, getting ram running right can be a nightmare and a constant source of issues when overclocking etc..
As an example, i had an old ddr2 set of corsair vengeance memory which needed 2.1v to run at the 'stated' speed stamped on the memory. The mobo would run it at a slower speed as standard, but wouldnt boot if i tried to run it at the stated 1600mhz or whatever it was. I upped the voltage to 2.1 and it worked. However be V V careful with voltages as even 1.5v seems extremely high for some memory these days....stick to no more than what the manufacturer recommends.
Cheers!!
Gassing Station | Computers, Gadgets & Stuff | Top of Page | What's New | My Stuff


