Pla filament 3d printing
Author
Discussion

sjj84

Original Poster:

2,396 posts

250 months

Tuesday 11th December 2018
quotequote all
Following on from the 3d printing thread from a few weeks back, I have ordered an ender 3. What brand of pla filament is everybody using, there seems to be a wide range of prices on Amazon all seemingly with good and bad reviews. Also is it worth getting the slightly more expensive pla+?

Spragnut

199 posts

204 months

Wednesday 12th December 2018
quotequote all
I didn't have much joy with PLA+, didn't print as well as standard PLA. May have been not enough time setting it up though, normal PLA just seems to work everytime.

As for brands, I use RigidInk PLA mostly - is definitely on the expensive side but I've never had an issue and must be 20+ rolls in now, I've also bought some Ziro Marble Color from Amazon - prints superb, I was really impressed and half the cost of Rigid, I'll definitely try more of this in the future, in fact they have a nice looking blue and translucent purple which I might stick on order!

I've just put a E3D V6 on my CR10 and have started printing PETG and Carbonyte from RigidInk, again both have been fantastic.

Insanity Magnet

616 posts

184 months

Wednesday 12th December 2018
quotequote all
I don't use an Ender 3 but have had good results from:

Rigid Ink PLA
Fabadashery PLA (loose coil, expensive but good colour selection)
Formfutura Easyfil
ColorFabb PLA/PHA & PLA
Polymaker Polyplus.

I get through quite a lot of Rigid Ink.

I have used PLA+ type material before (PLA/PHA is similarly tough IME) though tend not to bother as I'll now use PETG instead. Polymaker's Polymax is very good, though.

I haven't really tried any of the cheaper brands of PLA.

anonymous-user

85 months

Wednesday 12th December 2018
quotequote all
https://shop.3dfilaprint.com/

Great PLA - always had fantastic results with it.

sjj84

Original Poster:

2,396 posts

250 months

Wednesday 12th December 2018
quotequote all
Thanks for the suggestions, I'll have a look at those and get something ordered. Do you generally use coloured filaments, or just use say a white and then paint things? I'm assuming that's the only way if multiple colours are desired in a single model?

What is petg, I'm an absolute beginner with 3d printers, as I understand it the ender 3 can print pla or abs.

Insanity Magnet

616 posts

184 months

Wednesday 12th December 2018
quotequote all
sjj84 said:
Thanks for the suggestions, I'll have a look at those and get something ordered. Do you generally use coloured filaments, or just use say a white and then paint things? I'm assuming that's the only way if multiple colours are desired in a single model?

What is petg, I'm an absolute beginner with 3d printers, as I understand it the ender 3 can print pla or abs.
I tend to use coloured filaments and live with the bulk colours. If I really want something done properly I'll send CAD off to a prototyping house and have them make and paint/finish (I've started using my printers for rough and ready prototyping now I've worked out how to get good results out of them).

There are ways of printing in different colours. An expensive solution would be to buy a Mosaic Palette, which will allow you to mix colours throughout the model. You could also do a manual filament change if the model has defined bands of colour in the z-direction. Other than that you are looking at multi-head printers (or using dyed nylon... nylon's a different level of faff). Multihead printers also allow the use of soluble supports which enable the printing of really tricky geometry (though I've yet to see a properly clean supported FDM print out of anything but a Stratasys...). Painting might be easier!

PETG - glycol modified PET. Think mineral water bottle plastic and your are in roughly the right ballpark.

There's a reasonable guide at: https://www.simplify3d.com/support/materials-guide...
specifically https://www.simplify3d.com/support/materials-guide...

I tend to use PETG for mechanical parts (brackets, snap-fits) as it is generally fairly tough. You may find that you need to keep the spool fairly dry, though (dry out carefully in oven or buy a PrintDry) . Print temps tend to be between PLA and ABS though you will want the bed to be hot.

Edited by Insanity Magnet on Wednesday 12th December 22:53