Tips and Tricks Thread
Author
Discussion

Baldchap

Original Poster:

9,639 posts

123 months

Saturday 22nd March 2025
quotequote all
The tools you wish you'd bought sooner thread has been (whilst expensive in places) largely very useful to me. I think it's handy to stay abreast of new stuff and methods. I figured a handy tips for doing stuff thread might be equally helpful.

This week I had to expand some old spotlight holes by a couple of mm in a house I'm renovating for my parents. It's not something I've done before but how hard can it be?

I know from experience a holesaw without arbour bit just walks away so my initial approach was to draw round the right size hole cutter and then use a manual pull saw to expand the holes, but there were about ten to do, which is a PITA.

Off to YouTube and an old South African (by the accent) chap had the solution (sorry I don't have the video link) suggested making a little jig like this:



It's just a longer piece of timber with a smaller piece (that will fit through the hole for my arbour bit to reach) screwed on, with a hole the size of my arbour bit in the middle. I made this from some old flooring I had already removed with a multitool.

I then pop it through the hole and screw to the ceiling like this (smaller part facing down into the existing hole):



And voila, perfectly expanded spotlight hole!



Hope this helps someone one day.

What good tricks or tips have you found?

dickymint

29,243 posts

289 months

Saturday 22nd March 2025
quotequote all
That's a great hack clap

GasEngineer

2,335 posts

93 months

Saturday 22nd March 2025
quotequote all
dickymint said:
That's a great hack clap
Please don't call it a hack.

reggie747

300 posts

158 months

Saturday 22nd March 2025
quotequote all
A far easier method which does it without the need to fill that gaping screw hole afterwards is...

Cut a piece of (min) 6mm ply and then using your holesaw with the new size you need, pop a hole through the ply.
Proceed to remove the pilot bit from the holesaw and visually centre the ply, with hole, over your smaller hole and cut through the plasterboard again with the pilotless hole saw.

Job's a good 'un as they say down our way

dickymint

29,243 posts

289 months

Saturday 22nd March 2025
quotequote all
GasEngineer said:
dickymint said:
That's a great hack clap
Please don't call it a hack.
readit

"A life hack (or life hacking) is any trick, shortcut, skill, or novelty method that increases productivity and efficiency, in all walks of life"

tongue out

zalrak

708 posts

116 months

Saturday 22nd March 2025
quotequote all
This is an easier way to do this:

https://www.youtube.com/watch?v=xqFpizXUKPA

Baldchap

Original Poster:

9,639 posts

123 months

Saturday 22nd March 2025
quotequote all
zalrak said:
This is an easier way to do this:

https://www.youtube.com/watch?v=xqFpizXUKPA
Not if you don't have the original hole saw.

Baldchap

Original Poster:

9,639 posts

123 months

Saturday 22nd March 2025
quotequote all
reggie747 said:
A far easier method which does it without the need to fill that gaping screw hole afterwards is...

Cut a piece of (min) 6mm ply and then using your holesaw with the new size you need, pop a hole through the ply.
Proceed to remove the pilot bit from the holesaw and visually centre the ply, with hole, over your smaller hole and cut through the plasterboard again with the pilotless hole saw.

Job's a good 'un as they say down our way
That's even better!

anonymous-user

85 months

Saturday 22nd March 2025
quotequote all
On my last rental I had the sparky run the cables in position then went in the loft and screwed some wood above them. It was a bungalow so made it easier.

zalrak

708 posts

116 months

Sunday 23rd March 2025
quotequote all
Baldchap said:
Not if you don't have the original hole saw.
They are not expensive to buy, it does the job properly and gives a clean finish. Why mess about with a bodge when you can easily do it the correct and safe way?