JWM LiFe PO4 and A123 emulator fitted to my 12C today
JWM LiFe PO4 and A123 emulator fitted to my 12C today
Author
Discussion

meridian

Original Poster:

330 posts

314 months

Tuesday
quotequote all
The original McLaren battery finally failed on my 2012 12C Coupe last week. It had done quite well in fairness, 14 years and 26000 odd miles. With the car in it's carcoon, it was hooked up to CTEK lithium charger but essentially just died overnight as the charger just became inactive and clearly no power to any of the electrical circuits on the car

As most will know here, the original Lithium McLaren batteries have a kind of computer built within, or A123 to give it it's proper parlance, hence their hideously high prices. It doesn t control major functions as such, mainly the BMS Battery Status, but nevertheless must be in situ to prevent numerous error codes appearing

Now there is various information out there from sources as to the best solution

The options that are spoken about are simplified as:

1) Replace with original McLaren battery
2) Replace with Lithium Iron battery along with A123 emulator
3) Replace with Lithium Iron or even Lead Acid battery and deactivate the A123 functions from the vehicle ECU

It is quite fair to say that options 1,2 and 3 above are listed in cost order from VERY expensive, to FAIRLY expensive to QUITE cheap

It is also worth mentioning that some of the UK's most recognised McLaren specialists do not necessarily agree on whether option 2 or 3 are the way to go

Anyway, for me, I had decided that although the BMS A123 function, and some others are not critical, I would rather not be deleting/isolating ECU functions on what is a very special and complex car

That is when I phoned Jack Webb Motorsport (JWM) whom are well known for their knowledge on all things battery based, both from a Motorsport and McLaren perspective

I spoke to Arnie, Jack's dad, and found him very personable, but more importantly very knowledgeable. I had already intended to run a JWM A123 emulator on my car, but was considering a very high specification Lead Acid battery to go with it, purely on cost considerations

...however, after a short conversation with Arnie, I felt that that was not the right approach, and so ordered a JWM LiFe PO4 Gen1 battery and Gen 1 A123 emulator

The ordering and purchasing process was slick and easy, and 3 days later it all arrived

Replacing the battery on a 12C is not technically difficult at any level, but by the same token it s not a 5 minute job either

I'd had the battery out before when I changed the accumulators on my car so was familiar with it all anyway

In simple terms the frunk liner must be removed, simply by removing a multitude of screws and fasteners, and then the battery is revealed..

..the battery is clamped at both ends, but a little tip from me would be that if you remove the left hand clamp, centre clamp and then the negative terminal lead from the floor, then the right hand clamp can remain in situ (and that is the fiddliest of them all to remove)

Connecting the A123 emulator to the battery is simplicity itself, one x postive lead, one x negative lead, 1 x multipug that goes to the emulator, and then a single wire that goes to the car's loom plug (via a dedicated plastic holder)

Interesting point to note is that the car loom plug that originally goes to the A123 battery, and now the A123 emulator, utilises only the single wire mentioned on Gen 1 cars (and just 2 on Gen 2)

With everything back together, normal service was resumed, with the car firing up instantly, all BMS functions working correctly and no error codes

The only thing I did note is that the car s service interval display will have to be reset (eta. just reset time/date in vehicle settings to restore correct reading)

All in all, I am very pleased. I don't look to spend money that doesn't need spending, and this is not the cheapest solution, but on balance my car retains all it's original computer functions, and now has a battery that is appreciably more powerful in terms of it s Ah and CCA capabilities than the original...

...quite simply because LiFe PO4 battery technology has advanced very significantly in the last 14 years

As I have said, other options will be spoken about by others far more knowledgeable than me, and I do not question any of those options

I am simply saying here that I have had a very good service from JWM, and with the car now up and together again am very satisfied, and confident in the system s long term reliability

A good job done in terms of my long term future ownership of the car






Edited by meridian on Wednesday 18th November 11:02

Zorbathegreek

239 posts

15 months

Tuesday
quotequote all
Excellent post. I’ve been using JWM to look after a 720S and now 650S. 650S is still on original battery so will probably need changing at some point.

meridian

Original Poster:

330 posts

314 months

Tuesday
quotequote all
Yes, I have seen many of your posts Mick, regarding your quite amazing 650S, and know that JWM have completed very good work for you. I am happy to say that with regard to my recent experience JWM clearly live up to their excellent reputation. The advice given by Arnie, and subsequent service, along with their products are all top notch...