Plasma prob, Help!!
Discussion
Over the last few day my sony plasma has erm well gone a little strange, its turns on, as soon as the piccie comes on and the fans kick in, it turns off, and keeps doing this for anything up to 2 hours where it will finally settle down and stay on, there are a lot of techobobs on here ( thank god ) so hopefully someone might be able to help sourceing the prob, it weighs a ton, so it isnt a case of poping down to the tv repair shop, or is it simply on its way out ( its a few years old now ) and time for a new one, thanx in advance, Jez
Obviously if its always done this then there's a problem.
Although I imagine they are controlled fans, in that when certain components reach a certain temperature they switch one. WHen they go below this temperature it switches off. It may be fluctuating as it starts up as the temps are reasonable, but after its been on for a while it'll start to get hotter and the fans will be on constantly.
If it hasn't done it before and they are controlled, i suggest there's something wrong with the controller, or there is a lot of dust build up. Happens in laptops and the fans do similar things. If you can get some compressed air in there, go for that, but remember to shove a cocktail stick to prevent the fan spinning whilst you do it as otherwise you'll damage it.
I'd get some second opinions though, i'm no tv man
Although I imagine they are controlled fans, in that when certain components reach a certain temperature they switch one. WHen they go below this temperature it switches off. It may be fluctuating as it starts up as the temps are reasonable, but after its been on for a while it'll start to get hotter and the fans will be on constantly.
If it hasn't done it before and they are controlled, i suggest there's something wrong with the controller, or there is a lot of dust build up. Happens in laptops and the fans do similar things. If you can get some compressed air in there, go for that, but remember to shove a cocktail stick to prevent the fan spinning whilst you do it as otherwise you'll damage it.
I'd get some second opinions though, i'm no tv man

hhhmm dust build up could be the prob, didnt realise how dusty it was till i looked behind it, maybe the thing needs a service ( if that can be done ) but they are comming down in price now, so mite be worth just buying a new one and putting this on ebay, ( unless its a 2 quid fix lol )
I'd suggest that at least one analogue component has drifted out of range (perhaps a board-mounted potentiometer), or that something is drying out (age related) and the temperature as the TV warms up is bringing it back into operational range. It might also be a dry joint, although normally you can tell by giving it a swift whack.
Any competant TV engineer will be able to fix it, when you remove the screen the TV is actually a bog-standard television, not that different from a CRT. Sometimes they scratch out the names of ICs on the board to make it more difficult for independant engineers to repair, and I don't know how difficult it is these days for engineers to get hold of a circuit diagram.
You know that eventually it will point blank refuse to work
Best get it sorted sooner than later.
Any competant TV engineer will be able to fix it, when you remove the screen the TV is actually a bog-standard television, not that different from a CRT. Sometimes they scratch out the names of ICs on the board to make it more difficult for independant engineers to repair, and I don't know how difficult it is these days for engineers to get hold of a circuit diagram.
You know that eventually it will point blank refuse to work
Best get it sorted sooner than later.Same principles mate, it just lacks a tuner. Obviously not having a tube its going to be slightly different than a CRT, but not that much. Go to your local TV repair shop, give him the model number and serial number and see if he can get a circuit diagram for it. Or take it in on the off chance that he'll pull the back off and just have a sniff around. Sometimes you can very easily spot failed components (burnt out resistors for instance).
If its something on the power supply board (likely by your description), he won't even need a circuit.
>> Edited by Parrot of Doom on Thursday 9th March 12:46
If its something on the power supply board (likely by your description), he won't even need a circuit.
>> Edited by Parrot of Doom on Thursday 9th March 12:46
Parrot of Doom said:
I should add that sometimes the only fix is to replace an entire board - this is likely what an 'official' repair shop would do, its more profit for them.
again, thats a worry for me, plasma still being pretty new, i am sure some places will rip you off knowing that the customer knows bugger all about them
Eric Mc said:
Under gurantee?
Fraid not, bout about a year ago from a friend who paid a silly amount for it but needed cash quickly ( so i got it very cheap , as long as it cost no more than £500 to fix its worth it, anymore more than that and i'll bin it, they have dropped hell of a lot in price over the last year or so
Gassing Station | The Pie & Piston Archive | Top of Page | What's New | My Stuff





