Guitar amp sort of question
Guitar amp sort of question
Author
Discussion

esselte

Original Poster:

14,626 posts

298 months

Thursday 9th March 2006
quotequote all
My son has a 150w marshall bass amp.This has both a "line out" and an "XLR" out.Now I suppose these are for DI'ing into a mixer/recorder.The question is what is the difference and which would be best to use?I thank you.

Parrot of Doom

23,075 posts

265 months

Thursday 9th March 2006
quotequote all
Chances are they're no different. The XLR out is more likely to be electrically balanced though (although the line out if a stereo jack can be as well), which make for less chances of earth hum.

DieselJohn

2,114 posts

287 months

Thursday 9th March 2006
quotequote all
XLR is a completely different shape to the normal 1/4" jack plug DI? Use whichever you have the cable for. Don't think it will make any other difference.

http://en.wikipedia.org/wiki/XLR

http://en.wikipedia.org/wiki/Jack_plu


B17NNS

18,506 posts

278 months

Thursday 9th March 2006
quotequote all
Mic the speaker. Part of the beauty of a Marshall is the sound the speaker makes.

esselte

Original Poster:

14,626 posts

298 months

Thursday 9th March 2006
quotequote all
Parrot of Doom said:
Chances are they're no different. The XLR out is more likely to be electrically balanced though (although the line out if a stereo jack can be as well), which make for less chances of earth hum.


The xlr has an earth lift button associated with it which would eliminate the hum I suppose.Thanks POD

esselte

Original Poster:

14,626 posts

298 months

Thursday 9th March 2006
quotequote all
B17NNS said:
Mic the speaker. Part of the beauty of a Marshall is the sound the speaker makes.


Yes, but at home it's sometimes advisable not to rattle the cupboards!

AL666

2,679 posts

249 months

Thursday 9th March 2006
quotequote all
XLR has two leads inside it which run out-of-phase so that if any electrical distortion occurs between the amp and the mixer, the two signals are inverted again and the distortion will be cancelled out.

It's better to mic the speaker though (if you have a good microphone)

esselte

Original Poster:

14,626 posts

298 months

Thursday 9th March 2006
quotequote all
AL666 said:
XLR has two leads inside it which run out-of-phase so that if any electrical distortion occurs between the amp and the mixer, the two signals are inverted again and the distortion will be cancelled out.

It's better to mic the speaker though (if you have a good microphone)


See post above

The Dude

6,546 posts

278 months

Thursday 9th March 2006
quotequote all
The main difference is that XLRs will go to 11.

planetdave

9,922 posts

284 months

Thursday 9th March 2006
quotequote all
B17NNS said:
Mic the speaker. Part of the beauty of a Marshall is the sound the speaker makes.


It's not a straight 50 with a 100W 4*12 (a 1960TV would be nice)



If things haven't changed then the line out is possibly at a higher level (for slaving other amps) than the xlr which is a lower noise output more specifically for feeding higher end gear such as mixing desks. The balancing allows very long cable runs with minimal interference.

esselte

Original Poster:

14,626 posts

298 months

Thursday 9th March 2006
quotequote all
planetdave said:
B17NNS said:
Mic the speaker. Part of the beauty of a Marshall is the sound the speaker makes.


It's not a straight 50 with a 100W 4*12 (a 1960TV would be nice)



If things haven't changed then the line out is possibly at a higher level (for slaving other amps) than the xlr which is a lower noise output more specifically for feeding higher end gear such as mixing desks. The balancing allows very long cable runs with minimal interference.


Would it be OK to use the line out for input to a mixer?Or would it be too high a level?

planetdave

9,922 posts

284 months

Thursday 9th March 2006
quotequote all
Depends on your mixer . (cheap mixers often run at higher input levels). See your retailer

Usually best to have a 1/4" jack running to 1/4"jack and xlr to xlr though you can find exceptions to this rule of thumb.





slt said:
Would it be OK to use the line out for input to a mixer?Or would it be too high a level?


Try it. If it sounds wrong it probably is. Use lowest input gain first and go slowly.


>> Edited by planetdave on Thursday 9th March 15:32

esselte

Original Poster:

14,626 posts

298 months

Thursday 9th March 2006
quotequote all
planetdave said:
Depends on your mixer . (cheap mixers often run at higher input levels). See your retailer

Usually best to have a 1/4" jack running to 1/4"jack and xlr to xlr though you can find exceptions to this rule of thumb.





slt said:
Would it be OK to use the line out for input to a mixer?Or would it be too high a level?


Try it. If it sounds wrong it probably is. Use lowest input gain first and go slowly.


>> Edited by planetdave on Thursday 9th March 15:32

The mixer has both

GetCarter

31,329 posts

310 months

Thursday 9th March 2006
quotequote all
On big gigs they always take XLR out to the PA
On medium gigs they let you rattle the thing to pieces
On small gigs they just tell you to turn it down (or at least wait till the Bahmitsva is over)

love machine

7,609 posts

266 months

Thursday 9th March 2006
quotequote all
B17NNS said:
Mic the speaker. Part of the beauty of a Marshall is the sound the speaker makes.


Fully, might be an idea to isolate it in a room. I had problems with recording my hammond with the required speaker overdrive, it was earth shattering, turning it down made it sound pants. An old leslie 147 cabinet. Nice. Marshalls are similar.

GetCarter

31,329 posts

310 months

Thursday 9th March 2006
quotequote all
love machine said:
B17NNS said:
Mic the speaker. Part of the beauty of a Marshall is the sound the speaker makes.


Fully, might be an idea to isolate it in a room. I had problems with recording my hammond with the required speaker overdrive, it was earth shattering, turning it down made it sound pants. An old leslie 147 cabinet. Nice. Marshalls are similar.


You gotta' C5? (now is that spooky on a car site or what!)

number 46

1,019 posts

279 months

Thursday 9th March 2006
quotequote all
The jack line out is probably best and easiest as most mixer will have a jack socket input for the line input and an xlr for mic input, if you use the xlr mic input then it will probably be to high a level and you will need to pad it down. Depends on what sound you want, but if you want the Marshall sound you really need to mic the speaker as the sound is a combination of the amp and the speaker/cabinet. The usaul way would be to mic the cab. and use a Di direct from the bass before the amp this will give you a clean and a dirty sound, for this you will need a Di box. Check the amp manual/online, but the xlr out might be at lower level than the jack line out and may be at a different point out of the amp say pre power amp.

711

806 posts

256 months

Thursday 9th March 2006
quotequote all
If you want to mic. the speaker without blowing up the neighbours, an isolation or whisper box works quite well.

Basically a sealed box about 3 feet high with a speaker, mic and a s**t load of insulation sealed up inside! Probably a better technique for guitar rather than bass though...

Matamp made me a good one a couple of years ago, and it works quite well. I'm sure there are others on the market...speaker and power amp distorting volume levels and happy neighbours both at the same time