Decking
Author
Discussion

B17NNS

Original Poster:

18,506 posts

278 months

Friday 10th March 2006
quotequote all
I've built a couple of decks before in the last few years but I would like to build a round one (or one with a nice sweeping curve in it).

Can you get bendy joists?

Any suggestions on how to do this?

Flat in Fifth

49,021 posts

282 months

Friday 10th March 2006
quotequote all
No idea about bendy joists but bending timber is not difficult if you have a steam box.

Fairly normal task if you are into wooden boat building / restoration.

one link here > www.bluedome.co.uk/BB11/ribs.html

chim_knee

12,689 posts

288 months

Friday 10th March 2006
quotequote all
I'm no carpenter (despite my anorexia) but I believe you can cut a series of perpendicular (to the timber. i.e. they go the width of the timber, not the length) grooves in the back of the timber at and around the apex of the curve and this'll allow it to bend.

I know it's done for skirting board but I'd imagine it'd work on decking (though you may need to weather proof the cuts)

Edit: I assumed you meant the decking timbers, not the supporting joists. That solution is given below!

>> Edited by chim_knee on Friday 10th March 13:08

Witchfinder

6,388 posts

283 months

Friday 10th March 2006
quotequote all
I remember seeing a thing on telly where they made chariot wheels. The wheel rim was a single, straight piece of wood that was heated in an oven, and then bent into shape. Incredible really!

paulie-mafia

3,321 posts

254 months

Friday 10th March 2006
quotequote all
I assume you mean the joists supporting the decking? These don't need to bend at all, you just need to cut them to the correct lengths to support whatever shape you choose. Obviously you want to plan it to scale (graph paper, WH Smith), then you can easily work out where you need the supports.

B17NNS

Original Poster:

18,506 posts

278 months

Friday 10th March 2006
quotequote all
Was thinking along the lines of cutting shallow groves in the timber (as per the bendy mdf you can get) and getting it very wet.

pdV6

16,442 posts

292 months

Friday 10th March 2006
quotequote all
Peter Kay said:
Do you want decking?

jims2

208 posts

303 months

Friday 10th March 2006
quotequote all
Agree with paulie-mafia, the supporting framework doesn't have to be
circular. Hell of a work to make it that way.
Wouldn't you just make the framework at the very most a shape as near to
your circular dimension as possible maybe even a hex shape. Then when you
fix the actual decking boards they would be set with an overhang and then
you can trim this to the exact curve you are looking for.

Jim

B17NNS

Original Poster:

18,506 posts

278 months

Friday 10th March 2006
quotequote all
jims2 said:
Wouldn't you just make the framework at the very most a shape as near to
your circular dimension as possible maybe even a hex shape.Jim


that sounds like the best idea

angles or an octogon please...

ncs

3,974 posts

313 months

Friday 10th March 2006
quotequote all
B17NNS said:
Was thinking along the lines of cutting shallow groves in the timber (as per the bendy mdf you can get) and getting it very wet.


Dont even think about it - it will be allmost impossible to do & weaken the structure of your deck.

Drop me a line though my profile if I can be of any help

Nick
www.tbrewer.co.uk (just so you know)

CatherineJ

9,586 posts

274 months

Friday 10th March 2006
quotequote all
jims2 said:
Agree with paulie-mafia, the supporting framework doesn't have to be
circular. Hell of a work to make it that way.
Wouldn't you just make the framework at the very most a shape as near to
your circular dimension as possible maybe even a hex shape. Then when you
fix the actual decking boards they would be set with an overhang and then
you can trim this to the exact curve you are looking for.

Jim


As Jim and Paul have said, that is how you do it and I we build them day in day out.

>> Edited by CatherineJ on Friday 10th March 18:48

plug

1,136 posts

269 months

Friday 10th March 2006
quotequote all
If you want a curved base, you will have to laminate the joists, EG for a 6*2 joist you would take 4 strips of timber 6 inches by 1/2 inch at the length you need, cover the sides in glue bend to the shape you want and the clamp together. When the glue has set the joist will be curved. This is the only way to do it and keep the joist strong, do not put lots of cuts in the timber to bend it as it will have no strength.

>> Edited by plug on Friday 10th March 19:00

Parrot of Doom

23,075 posts

265 months

Friday 10th March 2006
quotequote all
You need to speak to a boat-builder

BTW the supporting frame can be angular, it doesn't matter. In fact it will be stronger.