Very Odd.......any explanations ??
Very Odd.......any explanations ??
Author
Discussion

Gorvid

Original Poster:

22,371 posts

256 months

Saturday 18th March 2006
quotequote all

There I was, sitting at my kitchen table browsing the interweb...
I had taken off a large brushed steel finger-ring about an hour ago and placed it alongside another ring on the surface of the table. About ten minutes ago I pushed them both out of the way to reposition my mouse mat.The larger ring stayed still (as if glued to the surface) so I pushed it away and it struggled off (as if held by a magnet). As I touched it I felt it was very warm, the other ring however was very cold (as metal tends to be).

I felt the table around where the ring was sat - this too was warm to the touch.....

Why would this happen ?

The warmth was very isolated to the ring and the table where it was sat - everything else was cold......

Andy Mac

73,668 posts

286 months

Saturday 18th March 2006
quotequote all
Different metals reacting?

>> Edited by Andy Mac on Saturday 18th March 20:15

rich 36

13,739 posts

297 months

Saturday 18th March 2006
quotequote all
move slowly away from the table and reach behind you in the drawer fro the meat cleaver

(egg whick might do)


then beat....


tskkkk spelling again, I'll just sort it


then beat......yourself severely and stop thinking about Derek acorah so much

>> Edited by rich 36 on Saturday 18th March 20:40

gopher

5,160 posts

290 months

Saturday 18th March 2006
quotequote all
Was the one ring in the area of the fan vent on your laptop and so got hot and melted the varnish on your table and so became glued?

Cheers

Paul

Andy Mac

73,668 posts

286 months

Saturday 18th March 2006
quotequote all
gopher said:
Was the one ring in the area of the fan vent on your laptop and so got hot and melted the varnish on your table and so became glued?

Cheers

Paul


Gorvid

Original Poster:

22,371 posts

256 months

Saturday 18th March 2006
quotequote all
gopher said:
Was the one ring in the area of the fan vent on your laptop and so got hot and melted the varnish on your table and so became glued?

Cheers

Paul


This is a very good call....

But the fan vent is on the other side....and there is about 8inches gap between the nearest (cold) side of the laptop and the warm place....

gopher

5,160 posts

290 months

Saturday 18th March 2006
quotequote all
Gorvid said:

This is a very good call....

But the fan vent is on the other side....and there is about 8inches gap between the nearest (cold) side of the laptop and the warm place....


bugger, that's the cleverist I've been all year........

rich 36

13,739 posts

297 months

Saturday 18th March 2006
quotequote all
is it him, in the pantry,




with the lead pipe?



oh I don't know

Gorvid

Original Poster:

22,371 posts

256 months

Saturday 18th March 2006
quotequote all
No worries - it was still clever

RING UPDATE: it's cold now

rich 36

13,739 posts

297 months

Saturday 18th March 2006
quotequote all
what sort of ring are DISCUSSING exactly?

and where might it be sported

turbobloke

117,583 posts

291 months

Saturday 18th March 2006
quotequote all
Gorvid said:
gopher said:
Was the one ring in the area of the fan vent on your laptop and so got hot and melted the varnish on your table and so became glued?

Cheers

Paul


This is a very good call....

But the fan vent is on the other side....and there is about 8inches gap between the nearest (cold) side of the laptop and the warm place....
Maybe similar - transformer in laptop or outside on adaptor? Other coils inside? If there are inductively wound coils inside then your ring may be heating up due to mag field near coils and melting varnish to get stuck. Transformer itself may stay cool due to positioning and fan taking hot air from this and processor out (the other side) while ring heats up.

Don't know about laptop internals so guessing away here

gopher

5,160 posts

290 months

Saturday 18th March 2006
quotequote all
Was the stuck ring closer to the lap top than the other? if so It could be the battery has heated the table varnish enough for that ring, but not enough for the other, I know my laptop battery gets very hot after just 30-40 mins use.

Cheers

Paul

Gorvid

Original Poster:

22,371 posts

256 months

Saturday 18th March 2006
quotequote all
rich 36 said:
what sort of ring are DISCUSSING exactly?

and where might it be sported


Gorvid....carefully said:
a large brushed steel finger-ring




rich 36 said:

lots of wierd and scary stuff across a few threads....


mxdi

13,994 posts

280 months

Saturday 18th March 2006
quotequote all



































BOO!!

Gorvid

Original Poster:

22,371 posts

256 months

Saturday 18th March 2006
quotequote all
The two rings were more or less touching and placed about 8inches to the left of the laptop.
The battery is about 3 feet below the table - but is right below the area....

The power cable passes within a couple of inches of the rings. The varnish is very old/solid BUT there is a bit of a subtle patch of something in that area...maybe a spillage from the other day

J1mmyD

1,823 posts

250 months

Saturday 18th March 2006
quotequote all
Wireless broadband connection?

That would be the electro magnetic dooberry that was on the same frequency as the thingumajig that caused an induction loop and warmed the ring, melting the varnish etc etc.

I hate to think how it works, but the PCM card does the same to pens and things I have near my laptop. Now ... see how far away you can place your major internal organs while still typing.

Gorvid

Original Poster:

22,371 posts

256 months

Saturday 18th March 2006
quotequote all
J1mmyD said:
Wireless broadband connection?


Yes


J1mmyD said:

Now ... see how far away you can place your major internal organs while still typing.


srebbe64

13,021 posts

268 months

Saturday 18th March 2006
quotequote all
Why don't you reposition the rings and laptop into the same position to see if it can be repeated?

Gorvid

Original Poster:

22,371 posts

256 months

Saturday 18th March 2006
quotequote all
RING UPDATE: the rings are now back in position - roughly