Brake pedal squidge removal?
Brake pedal squidge removal?
Author
Discussion

RobM77

Original Poster:

35,349 posts

265 months

Saturday 1st July 2006
quotequote all
I've spent today preparing my race car for the next race, and this entailed moving it and the Elise around the driveway. I instantly noticed that the race car (MG Metro) brake pedal was rock solid, but the Elise had an inch or two of squidge at the top, which ruins any chance of heel and toe when braking hard. Both cars have unservoed brakes (My Elise is an S2 111S). Can this squidge be removed? What causes it and why doesn't my Metro squidge in the same way? Failing that, I've been trying to find a link that someone posted on here to a spacer that bolted on to the top of the brake pedal - do they still make those?

I'd be grateful for any opinions

bogie

17,107 posts

303 months

Saturday 1st July 2006
quotequote all
i always find when I have new pads and/or the fluid change and the brakes bled then the pedal is very firm...but it deteroriates over time. I guess changing the fluid and bleefing them more regular is the only way....

Sam_68

9,939 posts

276 months

Saturday 1st July 2006
quotequote all
Bleeding the brakes is the first step.

If that doesn't solve the problem to your satisfaction, though, you may need to adjust the pushrod that links the brake pedal to the master cylinder.
the Lotus Workshop Manual said:
The pushrod length must be adjusted to apply a slight preload to the master cylinder with the pedal released. Too much preload will not allow the resevoir port to open. Too little preload will allow free play and a rattle from the pedal

Full instructions are in the workshop manual, but make sure you do it right - too much preload can have dire consequences!

hbaumhardt

950 posts

310 months

Saturday 1st July 2006
quotequote all
New disks, pads and fluid = rock solid pedal. Afther the first session on track the pedal travels a bit and I can never get that rock solid action back, no matter how much I bleed the system. Hey ho.

shangani

3,069 posts

268 months

Saturday 1st July 2006
quotequote all
As Hans said.

I would echo/add this:

1) Get braided steel brake hoses - only £50, but firm up the brake feel.
2) Junk the OEM pads - they are rubbish with poor initial bite. Get Pagid RS42's which will last sufficiently longer to justify the extra cost.
3) Change the brake fluid

Lastly, consider changing to decent discs when the OE ones wear out.

Sam_68

9,939 posts

276 months

Saturday 1st July 2006
quotequote all
hbaumhardt said:
New disks, pads and fluid = rock solid pedal. Afther the first session on track the pedal travels a bit and I can never get that rock solid action back, no matter how much I bleed the system. Hey ho.

New pads usually feel a bit 'springy'; possibly due to the initial gassing, but whatever, I've always found the sensation a little unpleasant as it is sending the message that the brakes aren't operating as effectively as they will once the pads have bedded in.

With regard to pedal travel, there is no technical reason why this can't be adjusted out at the pushrod, if you are careful, but you can't (or rather shouldn't) adjust the pedal to be absolutely solid, as this will mean that expansion of the fluid as it heats up in operation can make the brakes bind on.

With a correctly adjusted pedal pushrod and a thoroughly well-bled system, you should have no problem getting a good, firm pedal that is fine for heeling-and-toeing.

hbaumhardt

950 posts

310 months

Sunday 2nd July 2006
quotequote all
Or just learn to heal 'n toe with a little travel, ready for all situations then.

RobM77

Original Poster:

35,349 posts

265 months

Sunday 2nd July 2006
quotequote all
hbaumhardt said:
Or just learn to heal 'n toe with a little travel, ready for all situations then.


It isn't possible to heel and toe under hard braking at all, as my foot is down below the accelerator, trapped between clutch and accelerator pedals. I'm very flexible, and even stationary with some bizarre bending of feet it isn't possible to get onto the accelerator.

Thanks for the advice re: bleeding brakes etc. I may try that. Naturally, my race car runs braided hoses, racing fluid and constantly bled brakes. Maybe that is the difference?

Sam_68

9,939 posts

276 months

Sunday 2nd July 2006
quotequote all
A thorough pressure bleed may well transform it. At least it is cheap and easy enough to find out!

Certainly, I've not had any problem heeling-and-toeing in either of my Elises; the pedals are well positioned for it and the brakes, being unservoed, offer enough resistance even for a clumsy oaf like me!

shangani

3,069 posts

268 months

Sunday 2nd July 2006
quotequote all
RobM77 said:
hbaumhardt said:
Or just learn to heal 'n toe with a little travel, ready for all situations then.


It isn't possible to heel and toe under hard braking at all, as my foot is down below the accelerator, trapped between clutch and accelerator pedals. I'm very flexible, and even stationary with some bizarre bending of feet it isn't possible to get onto the accelerator.

Thanks for the advice re: bleeding brakes etc. I may try that. Naturally, my race car runs braided hoses, racing fluid and constantly bled brakes. Maybe that is the difference?


Rob - you seemed to have no problem heel-toeing in my car and I have improved the pedal position since then. There is a solution out there. Brake bleed is a cheap and easy start. Pedal adjustment later, then pads and lines.

Edited by shangani on Sunday 2nd July 12:24

RobM77

Original Poster:

35,349 posts

265 months

Sunday 2nd July 2006
quotequote all
shangani said:
RobM77 said:
hbaumhardt said:
Or just learn to heal 'n toe with a little travel, ready for all situations then.


It isn't possible to heel and toe under hard braking at all, as my foot is down below the accelerator, trapped between clutch and accelerator pedals. I'm very flexible, and even stationary with some bizarre bending of feet it isn't possible to get onto the accelerator.

Thanks for the advice re: bleeding brakes etc. I may try that. Naturally, my race car runs braided hoses, racing fluid and constantly bled brakes. Maybe that is the difference?


Rob - you seemed to have no problem heel-toeing in my car and I have improved the pedal position since then. There is a solution out there. Brake bleed is a cheap and easy start. Pedal adjustment later, then pads and lines.

Edited by shangani on Sunday 2nd July 12:24


Yes, at road speeds heel and toe is a synch in your 111S and likewise mine. It is only when braking heavily that I can't do it, as the brake pedal goes too low. This worries me because I'll be going on track next month. I think I may have been misleading in my original post - that isn't sqiudge at all - it is brake pedal travel (although the squidge before take up is annoying). I've just been for a nice 100 mile drive (to the New Forest for an ice cream - why not! ), and heel and toe came easily everytime I changed down (I never learnt to change down any other way - which is actually a problem when I drive a big car with widely spaced pedals!) - apart from when my passenger spotted the ice cream place at 60mph! (ish!) I had to brake heavily to turn in and when I tried to heel and toe I realised my foot was trapped down below the accelerator...

shangani

3,069 posts

268 months

Sunday 2nd July 2006
quotequote all
Brake bleed and braided lines are your friend. I also find pumping the brakes a bit before I go out for a session improves the bite point.

RobM77

Original Poster:

35,349 posts

265 months

Sunday 2nd July 2006
quotequote all
Thanks. I think braided lines sound like a good plan. I've got a service soon - I wonder if they could fit them? (the bill is going to be very scary!!! I've already got four new tyres and a geo check booked in!)

shangani

3,069 posts

268 months

Sunday 2nd July 2006
quotequote all
Hoses and fitting cost me about £150 total.

Also, Rob try this link regarding adjusting the pedal and getting rid of any play.

www.sandsmuseum.com/cars/elise/experience/maintenance/brakes/brakeadj.html

RobM77

Original Poster:

35,349 posts

265 months

Sunday 2nd July 2006
quotequote all
shangani said:
Hoses and fitting cost me about £150 total.

Also, Rob try this link regarding adjusting the pedal and getting rid of any play.

www.sandsmuseum.com/cars/elise/experience/maintenance/brakes/brakeadj.html


Not too bad at all. Thank you for the link and the advice!

Bill K 111

134 posts

244 months

Friday 28th July 2006
quotequote all
Sorry to drag an old topic to the top of the pile but I too had concerns about the height of the brake pedal in relation to the throttle pedal when using the car in anger on circuit. I checked that the height of the brake pedal was optimised but also checked the height of the throttle pedal and found it quite high. The throttle pedal TRAVEL is a finite range but the 'altitude' of that range is adjustable. There is an 'upstop' and a 'downstop.'

It's an absolute upside down back-killer but...by adjusting the pushrod that operates the throttle pedal under the dashboard to ensure it's longest (safe) length and then screwing in the downstop in the floor so that full throttle just kisses it, the throttle now sits comfortably lower than the brake pedal making it possible to heel and toe when braking hard even with a squidgyish brake pedal. You will have to adjust the upstop to take up the slack in the closed throttle position. Much easier to drive. Also interesting to note that slack had obviously crept into the cable over the years and full throttle was not actually being reached as it was prevented by a 'too high' downstop. Bonus. The car pulls even harder now too.