Valeting / detailing project for all you enthusiasts!
Discussion
PLEASE WAIT FOR PHOTOS TO LOAD AS THERE ARE A LOT OF THEM IT MAY BE SLOW. IF SOME ARE MISSING JUST CLICK REFRESH. THANKS
Ok so this is what ive been doing on my week off for the past three days!
Car detailing is relativly new to me as i wasnt even using the 2 bucket method, although i was and always am very throught with valeting my cars. Average wash time in total would be around 3 - 4 hours.
What i didnt realise was that i was actually doing more damage to my car using the products i was, i.e: chamois leather.
Here is a pic of my car after i had washed and cleaned as i normally would.
Then here is a pic of what it really looked like with a close eye.
Not good huh!!
So heres what i did.
I first visited www.polishedbliss.co.uk and read there guides to detailing and was amazed of the results that could be had. What a great web site and great guy for advise. Apparently lotus use a very hard laquer so you average polish wont do buggery even with a polisher.
I luckily had an orbital polisher knocking around at work which someone never collected so i brought the adapter for it.
By the way for all you novices out there i had never used a polisher before in my life
I must be brave or mad!
So this is what i did:-
I washed the car with a lambs wash mitton not a sponge as this will just create swirls in the laquer, i had two buckets, one with loads of soapy sudds and another with clear water. The idea is you rinse the sponge in the clear water before dumping it back in your soapy bucket so none of the crap goes in there and eventually on your car.
Rinse off as you would normally. I recently purchased an aqua gleam water filter with 0 parts per million and oh my god there good. £50 to your door but well worth the money. If it lasts me 6 months ill be chuffed. The idea is that you can let it dry without leathering off.
The water filter sells at a fixed price as far as im aware so the only bit you can save on is postage. Cheapest i found was www.parcfermeshop.com/products/accessories.php?cat=13
I did use poor boys waffle weave towel to get any excess water off which is the best alternative to a leather and is what we should be using if we have to.
Then i clayed the car which is basically rubbing the body work down with a clay bar and lubricant to remove any bugs, tar and sap off trees. This leaves the paintwork smooth and ready for cutting back. I used meguires quick clay and lubricant.
Then i washed it all over again just because i love it! Oh and this removes all the loose crap that is left behind from claying. I dryed it off thourghly this time. It was about 11pm when id got to this point after starting about 2pm so it dried overnight lovely.
I then removed all the wheels so i could give them a good wash and under the arches with the microfibre wash mitt. Yes i like to eat me dinner off the under side of my arches! I used turtle wax wheel cleaner from halfords dare i say it as i ahve always found it very good and it breaks down the most stubborn brake dust. Its in a lime green squirty gun (2 for 1 at the monet if your interested!).
Then i removed the rear lights and masked off everything on the car that didnt like polish. I.e: plastic & rubber, and yes theres a lot. Make sure you use the 3M high performance blue masking tape and not your usuall diy masking tape. You will need 2 rolls but if your tight you could probably get away with 1 but dont waste it. Make sure you take your time over this bit and cover everything because it will pay off. It took me about 2 hours.
Heres what it looks like when its all masked off.
Then i got the old orbital polisher out. It has 2 speeds on mine 2000rpm and 4000rpm, both bloody fast so luckily i had a variac which meant i could vary the input voltage to the polisher from 1 vac to 250 vac. I wanted to start relativly slow as i was unexperiebced with it. Although its worth noting that if you are using a compound like i did it needs to be going relativly fast to break the particals down in the compound.
So i used blackfire src compound with the orange polishing pad. All over probably took another 2 hours. This removed any deep scuffs and scratches and swirls preparing it for a finishing polish. I buffed it up with poor boys super thick & plush towel. I wasnt overly impressed at this point as i was expecting swirl free paint work. It was very smooth but still swirly. Dont give up though go to the next step.
So then i used the blackfire src finishing polish with the green polishing pad. I buffed up with poor boys super thick & plush towel. This is when i started to see the real difference. I was amazed at the results and this pushed me further.
I then glazed the car using Menzerna finishing touch glaze with the black polishing pad. I buffed up with poor boys delux megga towel. This give the colour real depth and agin i was stunned.
Ending in this result
That was the end of day 2, another gruling day.
First i peeled off all the blue tape and used the detailing brush to get all the polish out of all those hidden areas.
So then i was coming to the end. For waxing i used Zymol titanium wax. Some of you may know of the brand. If you dont you should and do now. They make the finest and best wax available and its so easy to use. Just put some in the palm of your hand and rub for a second then apply to the paintwork with your bare hands. Then just buff off after a couple of mins. I used zymols microfibre towel for this. Yes i know it £16 and the wax is £67 but they are well worth it i promise you. The towel is designed to absorb as little of the wax as possible. This means your forcing as much onto the paint work as possible. I brought these again from www.parcfermeshop.com/products/index.php?productid=26
All that was left to do then was to apply turtle wax wheel wax to the wheels. Again ive used this for some years and found it very good. It applys very well and makes brake dust easy to get of the next time. Green squirty gun again (halfords).
I dressed all the rubber an plastic and tyre walls with poor boys bold n bright. It left the surface wet looking but yet dry, superb!
All i did then was clean the leather with some leather cleaner ive had for some time and then a protective cream so it moisturises the leather.
Last of all i sat down and admired at what id acheived of ther the past three days. I was over the moon with the results and i was cuffed with my self.
Then i went to show it off at the local totty bar in Hagley in the west mids, The Lyttleton if anyone knows it or happend to be there! What a site it was.... And the car looked great too
I cannot stress how good the products ive used are. Please visit www.polishedbliss.co.uk as it is a fantastic site and the guy there is a star to speak to and will help in any way he can.
All products are from the above site unless otherwise stated.
Sorry if spelling is a bit crap but im knackered after typing all that!!
Oh and thats my mother in the picture not me. Thought id say that before any sarcy comments came out.
Ok so this is what ive been doing on my week off for the past three days!
Car detailing is relativly new to me as i wasnt even using the 2 bucket method, although i was and always am very throught with valeting my cars. Average wash time in total would be around 3 - 4 hours.
What i didnt realise was that i was actually doing more damage to my car using the products i was, i.e: chamois leather.
Here is a pic of my car after i had washed and cleaned as i normally would.
Then here is a pic of what it really looked like with a close eye.
Not good huh!!
So heres what i did.
I first visited www.polishedbliss.co.uk and read there guides to detailing and was amazed of the results that could be had. What a great web site and great guy for advise. Apparently lotus use a very hard laquer so you average polish wont do buggery even with a polisher.
I luckily had an orbital polisher knocking around at work which someone never collected so i brought the adapter for it.
By the way for all you novices out there i had never used a polisher before in my life
I must be brave or mad! So this is what i did:-
I washed the car with a lambs wash mitton not a sponge as this will just create swirls in the laquer, i had two buckets, one with loads of soapy sudds and another with clear water. The idea is you rinse the sponge in the clear water before dumping it back in your soapy bucket so none of the crap goes in there and eventually on your car.
Rinse off as you would normally. I recently purchased an aqua gleam water filter with 0 parts per million and oh my god there good. £50 to your door but well worth the money. If it lasts me 6 months ill be chuffed. The idea is that you can let it dry without leathering off.
The water filter sells at a fixed price as far as im aware so the only bit you can save on is postage. Cheapest i found was www.parcfermeshop.com/products/accessories.php?cat=13
I did use poor boys waffle weave towel to get any excess water off which is the best alternative to a leather and is what we should be using if we have to.
Then i clayed the car which is basically rubbing the body work down with a clay bar and lubricant to remove any bugs, tar and sap off trees. This leaves the paintwork smooth and ready for cutting back. I used meguires quick clay and lubricant.
Then i washed it all over again just because i love it! Oh and this removes all the loose crap that is left behind from claying. I dryed it off thourghly this time. It was about 11pm when id got to this point after starting about 2pm so it dried overnight lovely.
I then removed all the wheels so i could give them a good wash and under the arches with the microfibre wash mitt. Yes i like to eat me dinner off the under side of my arches! I used turtle wax wheel cleaner from halfords dare i say it as i ahve always found it very good and it breaks down the most stubborn brake dust. Its in a lime green squirty gun (2 for 1 at the monet if your interested!).
Then i removed the rear lights and masked off everything on the car that didnt like polish. I.e: plastic & rubber, and yes theres a lot. Make sure you use the 3M high performance blue masking tape and not your usuall diy masking tape. You will need 2 rolls but if your tight you could probably get away with 1 but dont waste it. Make sure you take your time over this bit and cover everything because it will pay off. It took me about 2 hours.
Heres what it looks like when its all masked off.
Then i got the old orbital polisher out. It has 2 speeds on mine 2000rpm and 4000rpm, both bloody fast so luckily i had a variac which meant i could vary the input voltage to the polisher from 1 vac to 250 vac. I wanted to start relativly slow as i was unexperiebced with it. Although its worth noting that if you are using a compound like i did it needs to be going relativly fast to break the particals down in the compound.
So i used blackfire src compound with the orange polishing pad. All over probably took another 2 hours. This removed any deep scuffs and scratches and swirls preparing it for a finishing polish. I buffed it up with poor boys super thick & plush towel. I wasnt overly impressed at this point as i was expecting swirl free paint work. It was very smooth but still swirly. Dont give up though go to the next step.
So then i used the blackfire src finishing polish with the green polishing pad. I buffed up with poor boys super thick & plush towel. This is when i started to see the real difference. I was amazed at the results and this pushed me further.
I then glazed the car using Menzerna finishing touch glaze with the black polishing pad. I buffed up with poor boys delux megga towel. This give the colour real depth and agin i was stunned.
Ending in this result
That was the end of day 2, another gruling day.
First i peeled off all the blue tape and used the detailing brush to get all the polish out of all those hidden areas.
So then i was coming to the end. For waxing i used Zymol titanium wax. Some of you may know of the brand. If you dont you should and do now. They make the finest and best wax available and its so easy to use. Just put some in the palm of your hand and rub for a second then apply to the paintwork with your bare hands. Then just buff off after a couple of mins. I used zymols microfibre towel for this. Yes i know it £16 and the wax is £67 but they are well worth it i promise you. The towel is designed to absorb as little of the wax as possible. This means your forcing as much onto the paint work as possible. I brought these again from www.parcfermeshop.com/products/index.php?productid=26
All that was left to do then was to apply turtle wax wheel wax to the wheels. Again ive used this for some years and found it very good. It applys very well and makes brake dust easy to get of the next time. Green squirty gun again (halfords).
I dressed all the rubber an plastic and tyre walls with poor boys bold n bright. It left the surface wet looking but yet dry, superb!
All i did then was clean the leather with some leather cleaner ive had for some time and then a protective cream so it moisturises the leather.
Last of all i sat down and admired at what id acheived of ther the past three days. I was over the moon with the results and i was cuffed with my self.
Then i went to show it off at the local totty bar in Hagley in the west mids, The Lyttleton if anyone knows it or happend to be there! What a site it was.... And the car looked great too
I cannot stress how good the products ive used are. Please visit www.polishedbliss.co.uk as it is a fantastic site and the guy there is a star to speak to and will help in any way he can.
All products are from the above site unless otherwise stated.
Sorry if spelling is a bit crap but im knackered after typing all that!!
Oh and thats my mother in the picture not me. Thought id say that before any sarcy comments came out.
Edited by Dave_s2_111s on Thursday 27th July 18:41
Andy
Love the racer! What a motor it looks with the stripes. Was thinking of viper striping mine but it would always be there in the back of my mind that the racer is painted stripes and mine would be plastic.
The gullwings are awsome. Just pop them off when i need to and slip them in the boot or leave them at home. I think the elise loos so much more sexy with a hard top. The beauty of it is being able to put it on and of so easy is just great. 30 Seconds and there off. Hard top to t-bar rarr
Get it!
Love the racer! What a motor it looks with the stripes. Was thinking of viper striping mine but it would always be there in the back of my mind that the racer is painted stripes and mine would be plastic.
The gullwings are awsome. Just pop them off when i need to and slip them in the boot or leave them at home. I think the elise loos so much more sexy with a hard top. The beauty of it is being able to put it on and of so easy is just great. 30 Seconds and there off. Hard top to t-bar rarr
Get it!
The shine is eyeblinding
some of you guys are realy nuts
polishing a car like that, my monstercar would like that too
he's killing to much flies lately
Also tell me more about that gulwing roof, are they silent?(not to much windnoise) and leakfree when you stand stil and rain is pooring down on the car?
I've seen them on some picture's before, and to me it looks like a good set up between a hardtop and a softtop, I'm more a harttop guy only when its hot I would take the roof of and spoil the lines
but with a good gulwing roof...you could have best out both worlds?
GTRene
some of you guys are realy nuts
polishing a car like that, my monstercar would like that too
he's killing to much flies lately
Also tell me more about that gulwing roof, are they silent?(not to much windnoise) and leakfree when you stand stil and rain is pooring down on the car?
I've seen them on some picture's before, and to me it looks like a good set up between a hardtop and a softtop, I'm more a harttop guy only when its hot I would take the roof of and spoil the lines
but with a good gulwing roof...you could have best out both worlds? GTRene
Now your making me sad with all your 11r racers coming out! How good do they look though, dribble! I wouldnt know whether to go for blue or red though. Fantastic car though,
Yer the gullwing was done at www.productionglassfibre.co.uk/
It does look amazing especially if you happen to go through a kentucky or mc d's drive through and just pop the one side up
sad i know.
Looks the mutz nutz with them both up though.
It is an aftermarket mod so its not 100% like an original manufacture job would be but its good enough for me and im a pedantic bugger, as you may tell, at the best of times.
You will never get it to be leak proof. Yes it leaks but i did re-position the seals the other day and it seams much better. Its because you breaking the seal twice that meets the hard top with the window so in theory its never going to be leak free. I think this is why lotus never put it into production. They did make a proto type on a liz but decided against it. This is were the glass fibre guys came into it. I recon they were rubbing their hands together that lotus decided against it.
I think for some people yes it would be no good but i only want to drive mine in the dry anyway so its ideal. Ill occasionally get caught in a shower but big deal.
If anyone is around the west mids area and considering it and wants to have a look their more than welcome.
Dave
Yer the gullwing was done at www.productionglassfibre.co.uk/
It does look amazing especially if you happen to go through a kentucky or mc d's drive through and just pop the one side up
sad i know. Looks the mutz nutz with them both up though.
It is an aftermarket mod so its not 100% like an original manufacture job would be but its good enough for me and im a pedantic bugger, as you may tell, at the best of times.
You will never get it to be leak proof. Yes it leaks but i did re-position the seals the other day and it seams much better. Its because you breaking the seal twice that meets the hard top with the window so in theory its never going to be leak free. I think this is why lotus never put it into production. They did make a proto type on a liz but decided against it. This is were the glass fibre guys came into it. I recon they were rubbing their hands together that lotus decided against it.
I think for some people yes it would be no good but i only want to drive mine in the dry anyway so its ideal. Ill occasionally get caught in a shower but big deal.
If anyone is around the west mids area and considering it and wants to have a look their more than welcome.
Dave
Spanking job, how on earth you have the patience I'll never know, looks like a hard job but as someone once said 'it's got to be hard to be worth having'...
Top marks, really need to get out and at least show mine some water, people are thinking I've got a matt black one.
Car, that is.
Thanks for the links, pics and the time to tell us how things should be done. You've made me feel guilty now though....
Top marks, really need to get out and at least show mine some water, people are thinking I've got a matt black one.
Car, that is.
Thanks for the links, pics and the time to tell us how things should be done. You've made me feel guilty now though....
Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff





Top work fella - fair play!