Discussion
Pros:
More responsive when you rev the engine under no load; engine therefore feels and sounds a bit racier.
Marginal improvement in acceleration, due to the reduced inertia of rotating masses.
Cons:
Idling won't be as smooth, particularly if you fit performance camshafts.
Easier to stall.
Ideally, you ought to be dynamically balancing the whole crankshaft/flyweel assembly; fitting a lightened flywheel on its own, you have no idea of engine balance.
It costs money.
More responsive when you rev the engine under no load; engine therefore feels and sounds a bit racier.
Marginal improvement in acceleration, due to the reduced inertia of rotating masses.
Cons:
Idling won't be as smooth, particularly if you fit performance camshafts.
Easier to stall.
Ideally, you ought to be dynamically balancing the whole crankshaft/flyweel assembly; fitting a lightened flywheel on its own, you have no idea of engine balance.
It costs money.
gooby said:
I have been told the main drawbacks are that the emissions will be messed up and the ECU may not be able to cope.
Quite possibly - I don't know enough about the K-series engine management to comment. My post was based on the typical pros and cons for any engine.
gooby said:
There are many negatives - is it worth it?
Unless you have a very specific reason for doing it, a lightened flywheel would be fairly well down my list of priorities for a modded car.
mr_c said:
He's got a Toyota. 

Yep - it is a Toyota (Yamaha) engine out of the 111R.
Lightened flywheel would be down the list of desired mods but while the engine is out I thought "why not". Tha main reason is that it seems that it is not just an "engine out" but also an engine strip down in order to get a dynamic balance with the crank. At the moment there is too much work happening - a engine strip would mean a wait or weeks.
Not worth it.
www.eliseparts.com/shop/index.php?main_page=product_info&cPath=157&products_id=374
These are being delivered on monday - when my baby is being re-assembled, these will be fitted. The oem disks have a huge lip and need changing. Will I have to order more pads? There is still a hell of a lot of meat on my Pagids.
These are being delivered on monday - when my baby is being re-assembled, these will be fitted. The oem disks have a huge lip and need changing. Will I have to order more pads? There is still a hell of a lot of meat on my Pagids.
Hi gooby
Was in the same situation a while back with my k engined S2. Whilst the engine was out it was suggested by my brilliant indie (tipton garage by budleigh salterton) to fit a lightweight flywheel he had lying around.
The intitial engine response is definately crisper due to less inertia. Any other benefits are marginal.Was also difficult to tell cause i had pistons rods and crank balanced at the same time. The idle is much weaker though which made it easier to stall at first until you get used to it. Sometimes stalls when hot and revs drop to idle at junctions but i'm sure the yota management is slick enough to prevent this. No problem now apart from people thinking you are just showing off when pulling away with staccato revs.
I wouldn't get one on it's own but if the flywheels accessible then it's £100 odd well spent.
Hope this helps, Nellie
Was in the same situation a while back with my k engined S2. Whilst the engine was out it was suggested by my brilliant indie (tipton garage by budleigh salterton) to fit a lightweight flywheel he had lying around.
The intitial engine response is definately crisper due to less inertia. Any other benefits are marginal.Was also difficult to tell cause i had pistons rods and crank balanced at the same time. The idle is much weaker though which made it easier to stall at first until you get used to it. Sometimes stalls when hot and revs drop to idle at junctions but i'm sure the yota management is slick enough to prevent this. No problem now apart from people thinking you are just showing off when pulling away with staccato revs.
I wouldn't get one on it's own but if the flywheels accessible then it's £100 odd well spent.
Hope this helps, Nellie
gooby said:
Very nice mate
Don't see why your meaty pagids should't see there time out either
twinpipe said:
the weight difference I think will be negligable compared to having a good poo
Reduction in overall vehicle weight isn't the objective. Lightweight flywheels are intended to reduce the rotational inertia of the engine (ie. to let it increase and decrease revs more quickly, beacuse there's less mass to spin up and down).
twinpipe said:
...It's not a step back and like you say the engines out anyway. Why not.
It could well be a step backwards, unless you have the engine balanced along with the new flywheel.
I would imagine that Yota engines designed to rev to 8K rpm are balanced to pretty fine tolerances when they leave the factory. Bolting on a lighter flywheel at random is not a good idea!
Sam_68 said:
It could well be a step backwards, unless you have the engine balanced along with the new flywheel.
I would imagine that Yota engines designed to rev to 8K rpm are balanced to pretty fine tolerances when they leave the factory. Bolting on a lighter flywheel at random is not a good idea!
I would imagine that Yota engines designed to rev to 8K rpm are balanced to pretty fine tolerances when they leave the factory. Bolting on a lighter flywheel at random is not a good idea!
the flywheel is not a balance as...and the tolerance of the yota engine is huge, remember every one has to get a drive in it...so it can handle that lightweight flywheel easely me thinks, it only is not bin done from the factory because most people can't drive a car so it owuld stalk and people complain...but when yor a sporty driver there is no problem, only happy revs
and ofcorse when you take of you need a bit more revs because of the less mass in the engine, but hey when you know that you don't stop
just rev
Do it gooby a better chance you don't get...but whats next on your list
here are some idea's that would welcome your lightweight flywheel
www.komo-tec.com/index.php/cPath/128_135
GTRene
GTRene said:
the tolerance of the yota engine is huge...so it can handle that lightweight flywheel easely me think
What are the factory figures for tolerance +/- on balance, Rene?
I know of no competent engine builder who would suggest replacement of the flywheel on an engine that revs to 8K rpm, without full balance of the crank/flywheel assembly, etc. For the marginal increase in responsiveness that you'd get from a lightened flywheel, it just isn't worth the risk.
Edited by Sam_68 on Saturday 12th August 15:09
I had a light flywheel on my Civic and it reveed to 9k happily (and still does to this day) .
I know of a lot of other cars (even race cars ) with light flywheels without issues. Can't see why all of a sudden it would be a problem on a Yota engined elise ?
I was one of the best mods I did to my Civic and as soon as I need to take my gearbox of my Elise I'll put on a light flywheel.
Haven't had any problems stalling either. It's not as bad as some people make it seem.
I know of a lot of other cars (even race cars ) with light flywheels without issues. Can't see why all of a sudden it would be a problem on a Yota engined elise ?
I was one of the best mods I did to my Civic and as soon as I need to take my gearbox of my Elise I'll put on a light flywheel.
Haven't had any problems stalling either. It's not as bad as some people make it seem.
I am not sure of the Elise standard flywheel weight. I wager that it is fairly light. So going lighter might not reap the same benefits as other cars, and in fact introduce some problems for day to day driving (idle, take off etc). I had a 9lb aluminium flywheel fitted to my '01 MX5 and that gave a lovely increase to response and a noticeable increase to acceleration in 1st and 2nd gear. No idle issues etc. Stock flywheel weight was 18lb I think.
Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff




