s1 idle problems
Discussion
sticking throttle body or idle air control valve.
grease the throttle linkage (pedal and throttle body end), and take out the idle air control valve (its a wee electronic thing in the intake manifold) and clean it with carb cleaner and then WD40. (if you pull it out, get someone to turn the ignition on and off BE CAREFUL and you should see the valve operate)
This is the advice i was given & it worked for me... Good luck
grease the throttle linkage (pedal and throttle body end), and take out the idle air control valve (its a wee electronic thing in the intake manifold) and clean it with carb cleaner and then WD40. (if you pull it out, get someone to turn the ignition on and off BE CAREFUL and you should see the valve operate)
This is the advice i was given & it worked for me... Good luck
Welcome Dave
This doesnt sound serious. Maybe an air leak on air intake area or possible faulty TPS sensor or IAC or even Lambada sensor or sticking throttle body.
Is it a plastic throttle body?
Dependiong on how up on the engine will depend on whether you will be able to sort it.
Couple of easy things to do/check.
Reset you IAC valve by turning ignition on (second key possition) and depress accelerator 5 times slowly.
If that doesnt work, see if there is any movement/play in the throttle body cable arm. If there is then that could be at fault.
If your more technical then grab a multi meter and pop it on volts DC and read between pins 2 and 3.
You should have a constant 0.6v approx in its idle position and arount 4.4v at WOT (wide open throttle).
You dont need to have the engine running just ignition on.
If you have reading that are fluctuating then you have a faulty TPS. Easy fix.
You could confirm that you have a constant 5v feed to the TPS by measuring between pins 1 and 3.
These may help:
http://homepage.swissonline.ch/TomsSe
http://forums.seloc.org/viewthread.ph
If your a bit unsure see if you can find your self a helpful elise owner by you or try a specialist.
I really wouldnt woory about it though it doesnt sound a major problem. I would think an hours labour plus parts (possibly one of the above mentioned £30-£80) should do it.
Were are u based?
Dave
This doesnt sound serious. Maybe an air leak on air intake area or possible faulty TPS sensor or IAC or even Lambada sensor or sticking throttle body.
Is it a plastic throttle body?
Dependiong on how up on the engine will depend on whether you will be able to sort it.
Couple of easy things to do/check.
Reset you IAC valve by turning ignition on (second key possition) and depress accelerator 5 times slowly.
If that doesnt work, see if there is any movement/play in the throttle body cable arm. If there is then that could be at fault.
If your more technical then grab a multi meter and pop it on volts DC and read between pins 2 and 3.
You should have a constant 0.6v approx in its idle position and arount 4.4v at WOT (wide open throttle).
You dont need to have the engine running just ignition on.
If you have reading that are fluctuating then you have a faulty TPS. Easy fix.
You could confirm that you have a constant 5v feed to the TPS by measuring between pins 1 and 3.
These may help:
http://homepage.swissonline.ch/TomsSe
http://forums.seloc.org/viewthread.ph
If your a bit unsure see if you can find your self a helpful elise owner by you or try a specialist.
I really wouldnt woory about it though it doesnt sound a major problem. I would think an hours labour plus parts (possibly one of the above mentioned £30-£80) should do it.
Were are u based?
Dave
Edited by Dave_s2_111s on Sunday 10th September 21:16
It it only happens when its warm then its going to be the throttle body. If it happens most of the time then clean the idle air control valve (link with picture below)
http://wiki.seloc.org/index.php/Idle_
http://wiki.seloc.org/index.php/Idle_
r thanks for the help guys thats great i have a aloy 52 mm throtle body looks ok and so does the pedle (i have had that one befor ) i have tryed the reseting the valve by pressing the trottle 5 times but it still does it every now and then i will try cleaning the valve on the body next just changed the exhaust manifold maybe the sensor has worked its way lose or some thing . i am from durham got a good dealer and a very good garage near by so if i dont do it i will send take it in thanks again
Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff




