Exige S dyno'd
Author
Discussion

jamwill79

Original Poster:

231 posts

249 months

Friday 15th September 2006
quotequote all
Afternoon all,
Anyone with an Exige S out there may be interested to know what my dyno results on tuesday were.
I have a standard S2 ITG induction kit fitted (mainly for the noise because I don't think it does much), Jim from 2bulars full system with de-cat, although the sports cat would also give same power results give or take a bit. 239.4 horses. Also about 8 more ftlbs torque. I reckon thats pretty good for an easy modification. Plus the owner of the place where it was done said he always gets lower power outputs on his dyno than at the other decent dyno centres.
I think someone has also done a power run with similar results. Has anyone else had a try??

jamieall

177 posts

261 months

Friday 15th September 2006
quotequote all
Keep an eye on how lean the car is running at high rpm. As you might know the 240R used 5 injectors and the 240 cup use 4 large ones. On the standard injectors which is what the S runs and the better flow, the injectors are likely to be running out of puff unless you start playing around with the ECU and the length of each squirt the injectors do. Also I was advised that the SC equipped cars suck a lot more air through their filters (obviously) and the standard one is very good at filtering the air but the performance filters tend to let fine particles through. When you add the high volume of air it can be a concern. The filter thing would be a more long term concern though.
Hope that helps
Jamie

S works

10,166 posts

281 months

Friday 15th September 2006
quotequote all
Which dyno and was that at the wheels, hubs or fly? Any powertraces?

Edited by S works on Friday 15th September 19:04

purpleperil

1,226 posts

315 months

Friday 15th September 2006
quotequote all
So how's that Bemani SC running Jamie? Was the uprated clutch a must?

emenel

891 posts

250 months

Friday 15th September 2006
quotequote all
jamwill79 said:
Afternoon all,
Anyone with an Exige S out there may be interested to know what my dyno results on tuesday were.
I have a standard S2 ITG induction kit fitted (mainly for the noise because I don't think it does much), Jim from 2bulars full system with de-cat, although the sports cat would also give same power results give or take a bit. 239.4 horses. Also about 8 more ftlbs torque. I reckon thats pretty good for an easy modification. Plus the owner of the place where it was done said he always gets lower power outputs on his dyno than at the other decent dyno centres.
I think someone has also done a power run with similar results. Has anyone else had a try??


Interesting figures Jamie. I've been looking at the 2bulars for a while now.

Is there a noticable difference in performance since the upgrades?

jamieall

177 posts

261 months

Friday 15th September 2006
quotequote all
Bemani is all good 90% of my milage since conversion has been on track and wow is it good
Apart from a oil pressure gauage doing its own thing (not part of the kit)its run very well, just have to manage the extra heat 2 cool down laps instead of one. Managed to boil my brake fluid a couple of times - after all I am running an extra gear on every straight
I am rather cean to get my hands on one of Emeralds ECUs when they do come out as they(Bemani) wont change the cam change over point on the 05 ECU - costing me a chunk of tourque.
Clutch wise there are two ways of doing it you either 'pre-engineer' strength and durablity into your package or you take the other path 'if it aint broke dont fix it' Some will run a standard clutch until it has a pre-mature death. I chose prior to conversion to fit a LSD (sent gear box to Quaife)and while the gear box was off fit a uprated clutch.
The Lotus dealers that fit the kit tend encourage the 'pre-engineered' aproach.

purpleperil

1,226 posts

315 months

Friday 15th September 2006
quotequote all
jamieall said:
The Lotus dealers that fit the kit tend encourage the 'pre-engineered' aproach.


Which kit?

jamieall

177 posts

261 months

Friday 15th September 2006
quotequote all
Errr the Bemani kit

purpleperil

1,226 posts

315 months

Saturday 16th September 2006
quotequote all
I assumed that the kit was not available in the UK?

jamwill79

Original Poster:

231 posts

249 months

Saturday 16th September 2006
quotequote all
Tim, I did the power run at WRC Technologies at silverstone. The place that Evo magazine do all their tests at. Must admit I don't know exactly how that figure is calculated. I'll have to look at the print-out again.
Unfortunately because of the back box I have, with the 90 degree angle bend at the tip, The air/fuel mixture couldn't be tested because the sensor couldn't go round the bend to get a good reading. This was the main reason I wanted to do the power run. Next time I'll have to take the undertray out and plug their kit straight into the exhaust sensor points. This running lean thing does concern me though. What do you guys think is the best thing do do about it now then?? Put everything back to standard?? Help please, I'm worried now.

jamieall

177 posts

261 months

Saturday 16th September 2006
quotequote all
I would not worry too much in the short term. Running lean can lead to higher cyclinder and piston temps though. I would suggest like myself you form an orderly que out side Emerald. Their ECU will be the ultimate solution and would allow you to change injectors maybe go a size smaller on the SC pulley and get something around the 260-270 output

Bemani is a Swiss tuner who allows the Swiss Lotus dealer to fit the kit, they also have Red motorsports in Germany fitting their kits. I believe they have over 80 kits on the road and track now. I went down to Switzerland to get the kit fitted see my thread on Exige.com in the My car section and look for 'time to come clean' as the title.
Plans has been thinking about trying to get the rights for the kit in the UK so might be worth asking them how they are getting along with that.

Edited by jamieall on Saturday 16th September 10:03

jamwill79

Original Poster:

231 posts

249 months

Saturday 16th September 2006
quotequote all
Thanks Jamie,
An Emerald ECU would be the answer then by the sound of it. I also know of someone who is putting a piggy back ECU on his S2 Exige at the moment. I don't know what make it is but its being tested out now. I'll keep an eye on it.

About the injectors. I'm sure when I rang Lotus themselves they told me that the injectors on the cup and the S were the same. They may possibly just be running at different rates.

Anyway, I'm sure the car can't be running all that lean. Also I don't constantly live in the 6000-8500 rev range and I always use the best petrol there is. When I go and get my geo done at Plans I'll see what they say. Ta

jamieall

177 posts

261 months

Saturday 16th September 2006
quotequote all
Lotus are famously inaccurate whan it comes to that kind of thing. I am sure they are different part numbers. I have seen nothing but problems with piggy back solutions as at some point the ECU learning functionality starts to fight the piggy. The only way to make them work is disengage the self learn functionality. Without dounbt the Emerald will be the proper solution

321freeflow

282 posts

252 months

Saturday 16th September 2006
quotequote all
jamwill79 said:
Thanks Jamie,
An Emerald ECU would be the answer then by the sound of it. I also know of someone who is putting a piggy back ECU on his S2 Exige at the moment. I don't know what make it is but its being tested out now. I'll keep an eye on it.

About the injectors. I'm sure when I rang Lotus themselves they told me that the injectors on the cup and the S were the same. They may possibly just be running at different rates.

Anyway, I'm sure the car can't be running all that lean. Also I don't constantly live in the 6000-8500 rev range and I always use the best petrol there is. When I go and get my geo done at Plans I'll see what they say. Ta


Well, there's a few of you out there now running this set-up with no problems reported. I believe Craig7l closely monitored the A/F ratio on his dyno runs with satisfactory figures recorded. He did say Optimax fuel (or equivalent) was best.

jamwill79

Original Poster:

231 posts

249 months

Saturday 16th September 2006
quotequote all
Hi Jim,
I'm sure your whole set-up I'm using is fine. Perhaps the only problem is the ITG induction. When I'm at plans I may get them to put back the standard air box and do without the fantastic induction roar. Also, if I put the sports cat on instead of de-cat my mil light might even turn off if I'm lucky.

S works

10,166 posts

281 months

Saturday 16th September 2006
quotequote all
I'd change the decat back to the sports cat first.

mevistox5

72 posts

252 months

Sunday 17th September 2006
quotequote all
jamieall said:
Lotus are famously inaccurate whan it comes to that kind of thing. I am sure they are different part numbers. I have seen nothing but problems with piggy back solutions as at some point the ECU learning functionality starts to fight the piggy. The only way to make them work is disengage the self learn functionality. Without dounbt the Emerald will be the proper solution


There are more things to be taken into account for here I think. Not only the total CC rate of the injectors, but also the the injector duty cycle. Then there is the fuel rail capacity. Can that handle enough flow (evenly distributed to ALL cylinders). And of course the fuelpressure (using a AFPR or a bigger fuelpump).

I agree with you Jamie that piggy back solutions are most of the time NOT the way to go. On the other side getting a new ECU (as in Emerald), can be a hard way too. Need to get a good base map first (for fuel and ignition), and most lack the sophistication of a OEM ECU, hence losing some function or loosing out on smoothness.

Nico

shay2nak

14 posts

245 months

Tuesday 19th September 2006
quotequote all
jamieall said:
Also I was advised that the SC equipped cars suck a lot more air through their filters (obviously) and the standard one is very good at filtering the air but the performance filters tend to let fine particles through. When you add the high volume of air it can be a concern. The filter thing would be a more long term concern though.
Hope that helps
Jamie

Could you still install a CAI and use a more dense filter that would catch the finer particles? If someone wanted the intake just for sound purposes and not really looking for much of a HP/TQ increase.