Bleeding the brakes. on an elise,
Bleeding the brakes. on an elise,
Author
Discussion

piooly

Original Poster:

1,176 posts

256 months

Saturday 23rd September 2006
quotequote all
I've just finished changeing the brake fluid on my elise S1, its easy to do so why pay the gargae. Only problem is I want the brake pedal to be rock solid and not have any play at the top of the pedal movement. Is this possible. I can get pretty good, but I still have an inch or so of travel before the brakes work, atleast it feels like an inch. I want it so that as soon as you touch the brake, its hard. Any suggestions?

GreenV8S

31,027 posts

315 months

Saturday 23rd September 2006
quotequote all
Be carefull not to go too far. That first bit if slack is absolutely essential for correct operation of the brakes.

piooly

Original Poster:

1,176 posts

256 months

Saturday 23rd September 2006
quotequote all
Just had a look on the net and found a place that said due the design of the elise front calipers, they need to be removed and inverted slightly to garrantee all air is removed.

The only reason I'm been fussy about this is because my mate had a westfield type kit car, no servos like the elise and the brake pedal is rock hard and just feels so good in comparison.....

GreenV8S

31,027 posts

315 months

Saturday 23rd September 2006
quotequote all
Changing the fluid doesn't normally involve getting air in the calipers, that should only be a problem if the system has been drained. Or do you mean you suspect the system wasn't bled properly in the first place?

Sam_68

9,939 posts

276 months

Saturday 23rd September 2006
quotequote all
It tells you in the factory workshop manual how to adjust the slack at the pedal, but as GreenV8S says, you have to be careful as too much preload at the master cylinder will prevent the resevoir port from opening.

....anyway, what are you doing lurking around the Elise forums, GreenV8S? Not thinking about buying a car that goes around corners properly, are you?

jondude

2,441 posts

248 months

Saturday 23rd September 2006
quotequote all
I'd be surprised if you did not have to have soem freeplay there, otherwise the brakes will grind - the piston seals have to be able to bounce the brakes off, and the freeplay gives you the margin for this.

( Admitted, I'm talking motorcycle brakes here, but the principle is nearly always the same, and the Elise has more in common with a motorbike than a standard car driving )

Sam_68

9,939 posts

276 months

Saturday 23rd September 2006
quotequote all
The free play at the pads should be pretty marginal; basically equal to the run-out on the discs. It is normal and correct for the pads to skimming the discs (ie. in very light contact). You will normally only get significant pad knock-off if the disc is not true (warped or unven surface).

Motorcyles are somewhat different, in that they usually use floating discs these days.

GreenV8S

31,027 posts

315 months

Saturday 23rd September 2006
quotequote all
Sam_68 said:
what are you doing lurking around the Elise forums, GreenV8S? Not thinking about buying a car that goes around corners properly, are you?


I thought perhaps if I skulked around here for a bit some of the handling might rub off onto mine ... hehe

Sam_68

9,939 posts

276 months

Saturday 23rd September 2006
quotequote all
GreenV8S said:
I thought perhaps if I skulked around here for a bit some of the handling might rub off onto mine ... hehe


rofl I know they managed to improve the Chrysler Sunbeam, Vauxhall Carlton and that Top Gear Lada, but there are some turds that just can't be polished, even by Lotus chassis engineers, you know?

Besides, it's traditional for TVR's to try and kill people on twisty roads... If you actually managed to make it handle, you'd probably end up with a bunch of Russian Mafia hitmen out to get you for ruining the marque's 'macho' image.

GreenV8S

31,027 posts

315 months

Saturday 23rd September 2006
quotequote all
I'll have you know there's Lotus technology in my little TVR! One of the Lotus technicians was kind enough to weld my trailing arm up after I broke it at Hethel. It's been replaced since then, but I'm pretty sure the Lotus handling charm is still working ...

hbaumhardt

950 posts

310 months

Sunday 24th September 2006
quotequote all
From my techwiki on seloc; Brake bleeding. Order; OSR, NSR, OSF, NSF. Wheels off for the rears, but can do it through the spokes at the front. For each caliper in turn, pump the brake pedal until it is solid then maintain the pressure whilst the other person puts a non return value on the brake nipple and releases it (11 mm spanner) until the pedal hits the deck.