Baffled sump .. when do you need one?
Baffled sump .. when do you need one?
Author
Discussion

NathanK

Original Poster:

80 posts

253 months

Wednesday 27th September 2006
quotequote all
At what point do you need a baffled sump? I've seen these in adverts for some elises/exiges, and my mate has one in his caterham. It's to avoid oil stavation in the top of the engine I believe.

At what point do you need one? I assume my standard S1 with understeer won't need one.

S works

10,166 posts

281 months

Wednesday 27th September 2006
quotequote all
If you're using sticky tyres (AO38's, 48's or Toyo R888's) and doing a lot of trackwork.

Sam_68

9,939 posts

276 months

Wednesday 27th September 2006
quotequote all
It's to avoid oil starvation throughout the engine, not just to the top end.

The sump is the 'resevoir' for oil at the bottom of the engine. The oil pump sucks oil up from the sump using a pick-up pipe. If you corner so hard that the oil surges away from the pick-up pipe to the extent that the end of the pipe is no longer submerged in oil, the pump is sucking thin air and there is nothing to lubricate any part of the engine.

Actually, this makes it sound worse than it is - you usually get aerated oil rather than no oil at all, and the engine can run for a few seconds with no oil circulation without too much damage, though it's obviously something you'd want to avoid.

A baffled sump just has baffles (plates) inside it that are carefully designed to stop the oil surging around as much.

So...you need a baffled sump if you do a lot of hard cornering. Understeer and oversteer don't matter, so much as overall cornering (and/or braking) force.

It is very unlikely that you'll need a baffled sump for road use, but if you are a good track day driver on sticky tyres, they can be necessary for circuit use.

You can tell whether you need one or not by watching to see if the oil pressure warning light is flickering on around hard corners (assuming you're brave enough to watch the instruments in the middle of a hard corner!), or by fitting an oil pressure gauge & watching to see if that drops or flickers on corners.

NathanK

Original Poster:

80 posts

253 months

Wednesday 27th September 2006
quotequote all
Many thanks. Top Answer!

S Works

10,166 posts

281 months

Thursday 28th September 2006
quotequote all
Once again Sam finds the words I couldn't - top answer that man thumbup

GTRene

22,807 posts

255 months

Thursday 28th September 2006
quotequote all
Indeed a good explination...I never could do with my poor English
Think I could need better oilflow too in my M coupe cilinderhead...4 finger folowers are a bit worn in just 29.000kmyikes always the best oil and I have the latest engine specs(I thought) build in my car 08-2004 but when I opened the engine because of tapping valve's I saw in the block 10-2003...aaaaaaaaaa what does that mean...in 01-2004 there was a new better oilpump! aaaaaaaaahhh the combination of the between oilpump(first 2001<>2002) was not that good...this one is better but stil not strong anough for high speed cornering it seems...but never done anny trackday with this car! then I remember that every weekend at least 2 times a week I drive through a very long corner sometimes doing 200km/u but mostly 180km/u orso, its my long corner to feel everything is ok, so at those speeds in that long corner I guess its a bit short on oil for that high revs in the corner, never does or did my oillamp comes on though...so now I replace everything to 2006 specs with parts out the Z4 M coupe engine and then I also change the cams, engine is open so origenal or schrick-cams and some extra horsies I choose for the last option then all that money is not for nothing, also the Z4 M oilpump just in case and I know its better so...hope in a few weeks all is fixed and the tapping noise is gone and some more horsies get backyes I know a bit of thread sorry but needed to share.
GTRene

Edited by GTRene on Thursday 28th September 15:01