Oiled up spark plugs
Oiled up spark plugs
Author
Discussion

Ketchie

Original Poster:

8 posts

241 months

Wednesday 18th October 2006
quotequote all
I'm new to this forum, so hello all. I do some of the work on my car, such as removing the gearbox, so am fairly confident however I'm having some trouble with the spark plugs oiling up.

My 924 has been off the road for some time. Put her back on the road after replacing the fuel meter as it was jammed on full. Lot of fuel in the oil! Since then I've had to keep taking the spark plugs out and cleaning or replacing them as they're oiling up. Only get about 200 miles out of them. Compression is fine at 140/ 150 on all 4 cylinders, however the valve stem oil seals were replaced just before the car came off the road so I suspect the piston rings. Until I have time/ money to do the rebuild I wanted to get opinions on if there's anything I can do to stop the plugs oiling up. I've read that possibly changing the oil can help (presumably to a thicker oil?) and that also changing the plugs to a higher temp plug might help.

Anyone has any comments?

Many thanks,

Ketchie

wildoliver

9,324 posts

247 months

Wednesday 18th October 2006
quotequote all
There's something strange here.

For a start the 924 FI system is very reliable, not very good for power but very reliable.

My first thought is the over fueling has washed the bores causing big bore wear thats allowing oil past the rings, however if the compression is good the rings and bore will be fine.

It cant be stem seals, even if they weren't fitted then nowhere near enough oil to oil thew plugs would come down.

Is there any major smoke on start up or running? (I mean major!)

I think you have the wrong plugs in it.

apusmelba

56 posts

272 months

Wednesday 18th October 2006
quotequote all
i havent any direct advice to help on this but try clarks-garage.com and you should find a procedure to diagnose your problem

Ketchie

Original Poster:

8 posts

241 months

Wednesday 18th October 2006
quotequote all
Hmm, yes I wondered if all the fuel had stuffed the rings but the compression confuses the issue! When I first got the car running it had the original bosch plugs in it (W5D from memory). When they oiled up I got another bosch set, but they have been superseded with plugs with a resistor in them. Tried them anyway seeing as I had them and they oiled up too. So bought another brand without a resistor and they have oiled up too. Sigh. There's no smoke at all though it uses about a litre every 200 miles, these engines are pretty heavy on oil but not to that extent. Have changed the oil 3 times since first getting the engine going, to flush all the fuel out, but only with cheap stuff until it starts behaving! Have only done 400 miles.

Thanks, will have another look at Clarks.

GreenV8S

31,027 posts

315 months

Wednesday 18th October 2006
quotequote all
I assume you replaced the contaminated oil after you fixed the original problem?

Is it oiling up all the plugs? If so I wouldn't suspect a mechanical problem, I'd look for some other fault causing a weak spark and/or keeping the plugs too cold. Once the engine is warm and under load it takes a huge amount of oil to foul plugs enough to stop them working, it will keep going with a smokescreen out the back. It doesn't take as much when the plugs are cold, but you'd still notice a substantial amount of blue smoke if the problem was caused by oil ingestion.

BliarsGoing

72,863 posts

270 months

Wednesday 18th October 2006
quotequote all
If it wasn't oiling the plugs before the stem seals were replaced and has started doing it since I would double check the seals again.... Could be a faulty one or a problem with their installation.

Ketchie

Original Poster:

8 posts

241 months

Thursday 19th October 2006
quotequote all
GreenV8S said:
I assume you replaced the contaminated oil after you fixed the original problem?

Is it oiling up all the plugs? If so I wouldn't suspect a mechanical problem, I'd look for some other fault causing a weak spark and/or keeping the plugs too cold. Once the engine is warm and under load it takes a huge amount of oil to foul plugs enough to stop them working, it will keep going with a smokescreen out the back. It doesn't take as much when the plugs are cold, but you'd still notice a substantial amount of blue smoke if the problem was caused by oil ingestion.


Oh yes, I've changed the oil 3 times since then. You wouldn't believe the amount of fuel in the oil, at least 4 litres!

Yes it's all 4 plugs. It's not even a lot of oil, just a dribble but it's enough to have a horrible lumpy tickover and missfire. Can force the car to rev but it's not happy. Yesterday when I put new plugs in it ran beautifully for 30 mins or so, well into normal engine temp, at tickover. Had the CO tester in the exhaust so wasn't reving the engine, held it at tickover. Then it decided to oil up the plugs. There's never any blue smoke.

The coil checks out electrically but I reckon I'll try another one to be sure.

Thanks, Ketchie

Ketchie

Original Poster:

8 posts

241 months

Thursday 19th October 2006
quotequote all
BliarsGoing said:
If it wasn't oiling the plugs before the stem seals were replaced and has started doing it since I would double check the seals again.... Could be a faulty one or a problem with their installation.


Nah sorry, think I misled you there. The stem seals were changed a good couple of thousand miles before the car went off the road with no problems.

Any other thoughts?

Thanks, Ketchie

wildoliver

9,324 posts

247 months

Thursday 19th October 2006
quotequote all
Are you anywhere near Yorkshire?

I have a LOT of experience on the 924 engine sounds like you need some help with this one.

nel

4,830 posts

272 months

Thursday 19th October 2006
quotequote all
This whole question is bizarre just because there is no oily smoking or that classic "old nail burning oil smell" out of the exhaust - this would definitely be the case if you were constantly getting quantities of oil up past the rings or down the valve stems. From your last post, it sounds almost like the car runs normally without burning oil then suddenly ingests loads of it, fouls the plugs and dies. I suppose this could be related to the oil getting up to temperature, reducing in viscosity then finding its way into the cylinders, but I'm sure that it would still be burning a bit of oil even when cold.

I tend to agree that it sounds like the plugs are fouling due to being the wrong heat rating, but if the car is consuming a litre of oil for 200 miles it must be going somewhere! What do the plugs look like when they come out - wet and oily or dry but with loads of black soot on them?

The only other thing that springs to mind but hasn't been mentioned yet is the crankcase breather system. If this is not working correctly then you can get a build up in crankcase pressure. This helps the oil to get up past the piston rings and could maybe (I'm scrabbling for ideas here!) force some oil up through the breather into the air induction system. Maybe someone who knows the 924 engine could say whether this is possible? If so you'd see traces of oil in the induction system downstream of the breather connection.

I await with interest the solution - best of luck!

zcacogp

11,239 posts

275 months

Thursday 19th October 2006
quotequote all
Ketchie said:
There's no smoke at all though it uses about a litre every 200 miles, these engines are pretty heavy on oil but not to that extent.
That's ALOT of oil. While I can see the logic of nto suspecting leaks/whatever if it is on all 4 cylinders, you are losing a lot of oil to somewhere if it is going at this rate.

Oil loss AND oiled plugs seems to point to an obvious conclusion. The confusion is that there isn't a permanent pall of blue smoke over your car.

Further than that I can't help. Sorry. But I sympathise - oil usage is very annoying.

Only other comment is that it can't be that hard to identify the right plug for your car. Start with everything correct, and work from there.


Oli.

wildoliver

9,324 posts

247 months

Thursday 19th October 2006
quotequote all
1: A good 924 does not use a lot of oil, mine used to not even drop down the dipstick between changes and that had 170K on it.

2: It could very well be a blocked breather, also check in the bottom of the air filter housing, there is nearly always a lot of oil in here but if its pooling it could cause this problem.

3: following on from above take off the rubber flexi hoses and clean them out too, again expect to find oil.

4: replace plugs with Champion n7y, unless yours is anearly 924 in which case use a wr6 Bosch.

5: check plug leads and dizzy cap and rotor arm, replace if necessary (probably nothing to do with the problem but do it anyway)

6: check timing.

All that lot should take about 25 mins on a saturday, and cost less than £20, if it is still happening we need to find out if its wetting its plugs or oiling them.

Please try that lot before anything else, its all basic service work anyway, you should clean the airbox and trunking out every 3000 mile service as these cars do put a lot of oil in to there.

Ketchie

Original Poster:

8 posts

241 months

Friday 20th October 2006
quotequote all
wildoliver said:
1: A good 924 does not use a lot of oil, mine used to not even drop down the dipstick between changes and that had 170K on it.

2: It could very well be a blocked breather, also check in the bottom of the air filter housing, there is nearly always a lot of oil in here but if its pooling it could cause this problem.

3: following on from above take off the rubber flexi hoses and clean them out too, again expect to find oil.

4: replace plugs with Champion n7y, unless yours is anearly 924 in which case use a wr6 Bosch.

5: check plug leads and dizzy cap and rotor arm, replace if necessary (probably nothing to do with the problem but do it anyway)

6: check timing.

All that lot should take about 25 mins on a saturday, and cost less than £20, if it is still happening we need to find out if its wetting its plugs or oiling them.

Please try that lot before anything else, its all basic service work anyway, you should clean the airbox and trunking out every 3000 mile service as these cars do put a lot of oil in to there.


Thanks. Good ideas all.

1. Oil consumption quoted in Haynes is 1.5 litre/ 1000km. Think they're a bit wrong there then! My car was never that bad before I took it off the road. There's no oil leak though so it's going somewhere! Not in the water either, still nice and blue and clear. My understanding is oil in the water is rare on the 924 as there's no water jacket around the pots.
2. Oil breather is clear. Took it off the air filter housing and can feel the air coming through. There is a build up of oil in the housing, it makes it way onto the air sensor plate sometimes and has to be cleaned off (gently!). The amount of air coming through the breather doesn't increase with engine revs, is that strange?
3. Yes the boots do also get oil in them, tricky little bleeders with all that bendy rubber.
4. Been using Bosch W5RDC as they're the ones listed for the car. It's a 1978 with points dissy. I asked for some hotter plugs twice but both times the guys went "huh?". Will try the Bosch 6's if you reckon?
5. Plug leads, rotor arm and cap are all relatively new. Maybe a thousand miles before the car went off the road. No cracks in the cap, nice and clean inside. The leads check out electrically. Have changed the points and condenser a couple of times, just in case!
6. Cam/ crank timing is spot on. Have changed the belt anyway. Dissy timing is ok.

Any more things to check? Sooner or later it's engine rebuild isn't it?

Ketchie

Ketchie

Original Poster:

8 posts

241 months

Friday 20th October 2006
quotequote all
wildoliver said:
Are you anywhere near Yorkshire?

I have a LOT of experience on the 924 engine sounds like you need some help with this one.


About as far as you can get, I'm in London. Lived in Leeds as a kid though so not sure I'm a Londoner yet.

Ketchie

Original Poster:

8 posts

241 months

Friday 20th October 2006
quotequote all
nel said:
This whole question is bizarre just because there is no oily smoking or that classic "old nail burning oil smell" out of the exhaust - this would definitely be the case if you were constantly getting quantities of oil up past the rings or down the valve stems. From your last post, it sounds almost like the car runs normally without burning oil then suddenly ingests loads of it, fouls the plugs and dies. I suppose this could be related to the oil getting up to temperature, reducing in viscosity then finding its way into the cylinders, but I'm sure that it would still be burning a bit of oil even when cold.

I tend to agree that it sounds like the plugs are fouling due to being the wrong heat rating, but if the car is consuming a litre of oil for 200 miles it must be going somewhere! What do the plugs look like when they come out - wet and oily or dry but with loads of black soot on them?

The only other thing that springs to mind but hasn't been mentioned yet is the crankcase breather system. If this is not working correctly then you can get a build up in crankcase pressure. This helps the oil to get up past the piston rings and could maybe (I'm scrabbling for ideas here!) force some oil up through the breather into the air induction system. Maybe someone who knows the 924 engine could say whether this is possible? If so you'd see traces of oil in the induction system downstream of the breather connection.

I await with interest the solution - best of luck!


Thanks.

Plugs are too new to have many deposits on them. The oil is in between the core nose and the body of the plug and is only a dribble. No where near the coated in oil pics I've seen. The deposits that I can see are a little black but that could be the oil as the CO is spot on.

The car runs lovely with new plugs. So far I've done this 4 times. With the original Bosch W5DC first, then Bosch W5RDC (now come with added resistor). Each time whilst the plugs are new and clean the car runs beautifully. On the 3rd set of plugs I risked a 150 miles trip on the motorway (with another set of spare plugs) and the car behaved itself. As soon as I had the car in the garage at tickover for more than 15mins it started running lumpy and missfiring again. Bung new plugs in and it's fine again immediately. But not for long!!

Breather seems to be clear. Air comes through anyway.

Please keep the ideas coming!

Thanks, Ketchie

GreenV8S

31,027 posts

315 months

Friday 20th October 2006
quotequote all
Is it possible you have a sticky injector or other problem causing one cylinder to run cold when it's off load? Once the plug has dropped down below it's 'self-cleaning' temperature range it will eventually foul, with or without an oil leak.

wildoliver

9,324 posts

247 months

Friday 20th October 2006
quotequote all
Not on a 924 as the injectors aren't electrically controlled, it is possible that one is blocked but then it would run rough, thats why it really needs to be looked at by someone who knows the engine, you see the problem could be its wetting its plugs, in which case it could be the 5th injector thats not cutting out, could be so many things, but if compression test is ok its unlikely to be engine rebuild.

I would advise a change to Champion N7 as I always used them, and I used Champion in my Lotus too as I found them less prone to fouling, I doubt its the problem but you never know.

Just try one more thing, run the engine, take the oil filler cap off and see if there is excessive gas escape, and try again when warm, also watch oil pressure it should be steady on that engine if its pulsing then that could be a possible problem pointing maybe (and very unlikely) at an oil jacket bleeding through headgasket in to cylinder, but I would only expect this on ONE cylinder not all 4.

Ketchie

Original Poster:

8 posts

241 months

Friday 20th October 2006
quotequote all
wildoliver said:
Not on a 924 as the injectors aren't electrically controlled, it is possible that one is blocked but then it would run rough, thats why it really needs to be looked at by someone who knows the engine, you see the problem could be its wetting its plugs, in which case it could be the 5th injector thats not cutting out, could be so many things, but if compression test is ok its unlikely to be engine rebuild.

I would advise a change to Champion N7 as I always used them, and I used Champion in my Lotus too as I found them less prone to fouling, I doubt its the problem but you never know.

Just try one more thing, run the engine, take the oil filler cap off and see if there is excessive gas escape, and try again when warm, also watch oil pressure it should be steady on that engine if its pulsing then that could be a possible problem pointing maybe (and very unlikely) at an oil jacket bleeding through headgasket in to cylinder, but I would only expect this on ONE cylinder not all 4.


Cold start valve you mean? That's fine, squirts fuel for only a few seconds when the engine's dead cold. Aux air valve's fine too. The oil pressure's ok, runs at 0.5 when dead hot at tickover, increases nicely with revs. Haven't taken the oil filler cap off, was wary of doing that as I took the rocker cover off to check oil was getting to number 4 camshaft lobes. Guess what happened?! Foolish, foolish me. Will take the oil filler off tonight and have a look. Will also get a set of Champions. Strangely last night it ran better with the old plug leads on, though the new ones (not new-new used for a couple thousand miles) check out electrically. I'm hopefull that with Champion plugs it'll be better...will get some tomorrow and let you know. Thank you again.

wildoliver

9,324 posts

247 months

Saturday 21st October 2006
quotequote all
You are using the proper Metal sleeved plug leads aren't you? While very unlikly that the wrong leads would ever cause this problem if you don't then your leads will last about 2000 miles if not.

Al 450

1,390 posts

252 months

Tuesday 9th October 2007
quotequote all
Ketchie, did you ever get to the bottom of this?

I'm having problems with oil on the plug but only on one cylinder of my 924.