928 WITH POWER DELAY
Discussion
Dont know if this helps,but my old dash 944 used to hesitate slightly if you just nailed the throttle.It worked much better if you squeezed the pedal progessivly to the floor. My indy said it was down to the early Motronic system that has pretty basic mapping. I know the 928S2 is from a similiar era.
Edited by HAB on Saturday 17th February 16:55
A standard 928 shouldn't do that. Could be a few things;
- If it's an auto....you know the 'box usually starts in 2nd? Could be the kickdown maladjusted. Try pulling off with the stick in "2" and see if it starts in 1st (it should)
- LH computer dying - mine got worse over time before finally giving up. Can be tested/rebuilt by JDS Porsche
- Knock sensor failure - one failing retards ignition by (IIRC) 4 degrees. Noticeably slower
- Service items (distributor caps, plug leads, plugs)
- One of the fuel pumps weak/dying
- clogged injectors
Ian
- If it's an auto....you know the 'box usually starts in 2nd? Could be the kickdown maladjusted. Try pulling off with the stick in "2" and see if it starts in 1st (it should)
- LH computer dying - mine got worse over time before finally giving up. Can be tested/rebuilt by JDS Porsche
- Knock sensor failure - one failing retards ignition by (IIRC) 4 degrees. Noticeably slower
- Service items (distributor caps, plug leads, plugs)
- One of the fuel pumps weak/dying
- clogged injectors
Ian
ADDI said:
Thanks for the advice, i will start with the service parts and some injector cleaner. Where abouts does the Air Flow Meter live. I've been told that could do it before.
Somewhere between the air filter and the throttle body, in the middle of a big black rubber hose. Sort of a squarish box with wires coming out. I'm assuming Motronic injection with wires going to each injector - not CIS.
I have a similar sort of thing with (though it doesn't sound quite as bad) with my Cossie Merc. It feels just like it is turbo charged, needing a moment to spool up. Not a misfire - just a 'flatness'.
Please report back if you get to the bottom of it! I believe it could be my air flow meter... I figure that if it's not detecting the increased air flow, then it won't inject extra fuel so acceleration will suffer and the throttle response will be poor?
This is on CIS Jetronic, not Motronic though
Please report back if you get to the bottom of it! I believe it could be my air flow meter... I figure that if it's not detecting the increased air flow, then it won't inject extra fuel so acceleration will suffer and the throttle response will be poor?
This is on CIS Jetronic, not Motronic though
Edited by pentoman on Monday 19th February 13:56
pentoman said:
This is on CIS Jetronic, not Motronic though
What age is that? CIS = mechanical continuous injection system = big flappy airflow meter.
More tricky to diagnose than motronic partly because no one knows that much about them now.
Variations included I think a throttle position sensor. Not sure about any accelerator pump. I'd check the accumulator is still accumulating, and not leaking.. (normally it leaks back to the tank). It keeps constant pressure even when a sudden fuelling requirement happens.
Globulator said:
pentoman said:
This is on CIS Jetronic, not Motronic though
What age is that? CIS = mechanical continuous injection system = big flappy airflow meter.
More tricky to diagnose than motronic partly because no one knows that much about them now.
Variations included I think a throttle position sensor. Not sure about any accelerator pump. I'd check the accumulator is still accumulating, and not leaking.. (normally it leaks back to the tank). It keeps constant pressure even when a sudden fuelling requirement happens.
It's a 1990 car but the model came around in '85. KE Jetronic with flappy plate "toilet seat" air flow meter, an EHA to perform automatic mixture adjustment, intake temp sensor, barometric pressure adjuster, engine temperature sensor, no lambda sensor. Unfortunately that's the extent of my knowledge of the system (yet sadly probably still more than 99.99% of people as you say).
Sorry for this minor hijack but hopefully it will be relevant! Do CIS and motronic (EFI) both have an accumulator? That sounds like it could be a culprit. But there's so many things that it could be, you need all the service manuals (which I have) and additionally some serious will power (which I haven't) plus tools and in some cases resistors of a certain ohm-age to test it all
grr. To apologise to OP for thread hijacking, here's a great "basics of engine management" article.
www.emeraldm3d.com/ems.htm
pentoman said:
It's a 1990 car but the model came around in '85. KE Jetronic with flappy plate "toilet seat" air flow meter, an EHA to perform automatic mixture adjustment, intake temp sensor, barometric pressure adjuster, engine temperature sensor, no lambda sensor. Unfortunately that's the extent of my knowledge of the system (yet sadly probably still more than 99.99% of people as you say).
Sorry for this minor hijack but hopefully it will be relevant! Do CIS and motronic (EFI) both have an accumulator? That sounds like it could be a culprit. But there's so many things that it could be, you need all the service manuals (which I have) and additionally some serious will power (which I haven't) plus tools and in some cases resistors of a certain ohm-age to test it all
grr.
The knowledge of what to look for is the best thing to have! Sorry for this minor hijack but hopefully it will be relevant! Do CIS and motronic (EFI) both have an accumulator? That sounds like it could be a culprit. But there's so many things that it could be, you need all the service manuals (which I have) and additionally some serious will power (which I haven't) plus tools and in some cases resistors of a certain ohm-age to test it all
grr.At least you've got a lot more space under that bonnet than on the 930. I have a CIS pressure gauge so if you are near Cambs PM me and we could have a go at measuring the system pressure.
I changed out my 1988 accumulator the other day and it did appear to be defunct, they are pretty old now. I got it from Pelican parts in the US but you may find it here cheaply too.
I think motronic just has the fuel pressure regulator at the end of the rail.
Globulator said:
pentoman said:
It's a 1990 car but the model came around in '85. KE Jetronic with flappy plate "toilet seat" air flow meter, an EHA to perform automatic mixture adjustment, intake temp sensor, barometric pressure adjuster, engine temperature sensor, no lambda sensor. Unfortunately that's the extent of my knowledge of the system (yet sadly probably still more than 99.99% of people as you say).
Sorry for this minor hijack but hopefully it will be relevant! Do CIS and motronic (EFI) both have an accumulator? That sounds like it could be a culprit. But there's so many things that it could be, you need all the service manuals (which I have) and additionally some serious will power (which I haven't) plus tools and in some cases resistors of a certain ohm-age to test it all
grr.
The knowledge of what to look for is the best thing to have! Sorry for this minor hijack but hopefully it will be relevant! Do CIS and motronic (EFI) both have an accumulator? That sounds like it could be a culprit. But there's so many things that it could be, you need all the service manuals (which I have) and additionally some serious will power (which I haven't) plus tools and in some cases resistors of a certain ohm-age to test it all
grr.At least you've got a lot more space under that bonnet than on the 930. I have a CIS pressure gauge so if you are near Cambs PM me and we could have a go at measuring the system pressure.
Thanks kindly for the offer but I'm in Gloucestershire... My dad probably has one, he's a mechanic, so I guess I should go use his if I can bring myself to (he likes to do things properly, I prefer to just mess around and see what happens
) and I can find what the pressure should be. Just found it: 5.8 bar. How long does it take to test?
Agreed I am lucky to have lots of space under the bonnet. Even so, some stuff still seems like a real hassle. And I fix computers for a living...
pentoman said:
Thanks kindly for the offer but I'm in Gloucestershire... My dad probably has one, he's a mechanic, so I guess I should go use his if I can bring myself to (he likes to do things properly, I prefer to just mess around and see what happens
) and I can find what the pressure should be.
Just found it: 5.8 bar. How long does it take to test?
Agreed I am lucky to have lots of space under the bonnet. Even so, some stuff still seems like a real hassle. And I fix computers for a living...
The actual pressure you are looking for can vary, depending on model/setup. There is a run and a rest pressure, the rest pressure being below the injector opening pressure but above vapourisation pressure, and bleeds away completely after about 30 minutes.
) and I can find what the pressure should be. Just found it: 5.8 bar. How long does it take to test?
Agreed I am lucky to have lots of space under the bonnet. Even so, some stuff still seems like a real hassle. And I fix computers for a living...
Therefore before undoing anything to change, leave it to rest (overnight is good). Prepare for petrol dripping/running/gurgling out with tissues/absorbent spill pads. Try not to smoke.
There is also a counter control pressure, which pushes back the air flap, more pressure = less fuelling for that. In the order of importance I'd say are:
General system condition (wear/corrosion)
Filters and gauzes clean (not sure where all the little gauze filters are)
Warm up regulator function/calibration
Accumulator
and for starting issues, accumulator, check valve, fuel distributor seals, injector seals.
The correct way to fix it is learning about the system and computing which bit may be faulty (on Google you will find fault-finding charts). If you can get the bits cheaply and are happy fitting them yourself then the replacement of the suspicious is another tack, but these parts are no longer very cheap when new

Ooh an interesting old thread to dig up.
ADDI - have you got anywhere with your problem?
Globulator - hope you're still on board with us!
Since this thread, I rebuilt my top end due to rather poor compression (have a thread with pics called "engine surge" in the engine section). Lots more torque, a little more power which shaved 1.5s from the 0-100 mph time. I am now certain the engine is in fine condition. However I'm still frustrated by the lack of decent throttle response. It still feels like you have to wait for a bit before the engine responds to the throttle - particularly annoying when really pressing on. The throttle response doesn't seem very progressive. With a short stroke n/a twin cam like this you expect crisp response!!
Perhaps the pressure is too high which is forcing back the air flow meter too much and making it harder for the mechanical air flow meter to be pushed down?
Russell
ADDI - have you got anywhere with your problem?
Globulator - hope you're still on board with us!
Since this thread, I rebuilt my top end due to rather poor compression (have a thread with pics called "engine surge" in the engine section). Lots more torque, a little more power which shaved 1.5s from the 0-100 mph time. I am now certain the engine is in fine condition. However I'm still frustrated by the lack of decent throttle response. It still feels like you have to wait for a bit before the engine responds to the throttle - particularly annoying when really pressing on. The throttle response doesn't seem very progressive. With a short stroke n/a twin cam like this you expect crisp response!!
Perhaps the pressure is too high which is forcing back the air flow meter too much and making it harder for the mechanical air flow meter to be pushed down?
Russell
Gassing Station | Porsche General | Top of Page | What's New | My Stuff



