Feedback request on engine upgrade pls
Discussion
Good Morning chaps,
My car is due to have the below engine mods in the next couple of weeks and i was after some bhp / torque figures from you guys who had had similar work done so i know what to expect for my money. I posted this on Seloc a while ago so apologies if some of you have seen this before... Thx in advance and have a good day!!
(running standard s1 exige engine and block conversion will be carried out on original k series)
Block conversion to 1.9 (upgrading con rods / pistons etc)
Head port and polished
Vernier pulleys incl upgraded cam belt
Emerald ecu remap
ITG air flow system
AP Racing Clutch
My car is due to have the below engine mods in the next couple of weeks and i was after some bhp / torque figures from you guys who had had similar work done so i know what to expect for my money. I posted this on Seloc a while ago so apologies if some of you have seen this before... Thx in advance and have a good day!!
(running standard s1 exige engine and block conversion will be carried out on original k series)
Block conversion to 1.9 (upgrading con rods / pistons etc)
Head port and polished
Vernier pulleys incl upgraded cam belt
Emerald ecu remap
ITG air flow system
AP Racing Clutch
Correct me if im wrong mate as i havent looked into that side of things too deeply, honda/audi conversion for 9k pls 4k for supercharger on top? 13k total cost...?
Those bits im having done will not be near that lol, i wish i had more dollar to throw at the car but that just isnt feesable at the moment. Car is in a lotus garage having bottom end rebuild under warranty so i thought it a good opportnity whilst the rear clam was off and engine out to have those bits done...
Speaking to a few guys on seloc that have gone the 1.9 bore out route on the k series block, they've quoted anything between 210 and 250 bhp which is quite a difference. No-one at present has given any torque indication though which is what im more interested in.
My only concern is i want a reliable conversion that i can use say every weekend and not have to rebuild frequently at huge cost. I have been advised that the 1.9 would be putting the engine under less stress than the 1.8 and would last longer if looked after properly?!?
Obviously you chaps would know more about this side of things than myself as ive only really been following lotus and the basic workings of the car for the past year or so...
Those bits im having done will not be near that lol, i wish i had more dollar to throw at the car but that just isnt feesable at the moment. Car is in a lotus garage having bottom end rebuild under warranty so i thought it a good opportnity whilst the rear clam was off and engine out to have those bits done...
Speaking to a few guys on seloc that have gone the 1.9 bore out route on the k series block, they've quoted anything between 210 and 250 bhp which is quite a difference. No-one at present has given any torque indication though which is what im more interested in.
My only concern is i want a reliable conversion that i can use say every weekend and not have to rebuild frequently at huge cost. I have been advised that the 1.9 would be putting the engine under less stress than the 1.8 and would last longer if looked after properly?!?
Obviously you chaps would know more about this side of things than myself as ive only really been following lotus and the basic workings of the car for the past year or so...
£10k will give you a reliable 220bhp with a Honda with the option of 300bhp with the supercharger (futher cash). The VHPD seems to need rebuilds every 30/40k to help avoid the hand grenade behaviour, so putting 210/250 I'm pretty sure you're still looking rebuild costs sometime in the future.
Although as you're already have the work done, probably makes sense to do what you're doing. I'm not sure about the 1.9 putting less stress on the engine, but as Tim says above speak to Dave Andrews www.dvapower.com/
Although as you're already have the work done, probably makes sense to do what you're doing. I'm not sure about the 1.9 putting less stress on the engine, but as Tim says above speak to Dave Andrews www.dvapower.com/
There are so many more variables than just the capacity. Let's take this component by component:
Head - VVC or MS2 (VHPD) head has bigger valve sizes and will be easier to get top flow from than any other k variants. Another option is to get the vulcan head from PTP, which is a modified MS2 head with slightly better flow. If your head is in decent nick, then it should be fine to work on.
Inlet - You will be running the standard exige throttle bodies I take it? There are better options. Trumpet lengths?
Cams - 285 cams will give good on-road performance while retaining the hydraulic lifters. Low maintenance, good torque and probably about 210 bhp on a decent 1.9 bottom end.
Other options 1444 cams - somewhat hotter - ideally to be used with solid lifters. This will not be quite as good low down, but will rpovide more top end power and torque. IIRC the 250 bhp 1.9's run by David Skeggs and Steve Butts use these cams.
Decent rods and forged pistons are a must. You could reuse your VHPD rods, but Steve Butts had a failure on one of these.
Block? Scholar open deck?
Crank - will you use your VHPD crank? May make the engine somewhat harder to balance etc. Anyway, it would be worth getting the bottom end / flywheel / clutch etc balanced properly to help reduce stresses on the engine.
All in all, depending how far you are willing to go, you should see somewhere between 210 and 240 bhp with a decent emerald mapping session. Torque will be good. Longevity? Don't know.
Head - VVC or MS2 (VHPD) head has bigger valve sizes and will be easier to get top flow from than any other k variants. Another option is to get the vulcan head from PTP, which is a modified MS2 head with slightly better flow. If your head is in decent nick, then it should be fine to work on.
Inlet - You will be running the standard exige throttle bodies I take it? There are better options. Trumpet lengths?
Cams - 285 cams will give good on-road performance while retaining the hydraulic lifters. Low maintenance, good torque and probably about 210 bhp on a decent 1.9 bottom end.
Other options 1444 cams - somewhat hotter - ideally to be used with solid lifters. This will not be quite as good low down, but will rpovide more top end power and torque. IIRC the 250 bhp 1.9's run by David Skeggs and Steve Butts use these cams.
Decent rods and forged pistons are a must. You could reuse your VHPD rods, but Steve Butts had a failure on one of these.
Block? Scholar open deck?
Crank - will you use your VHPD crank? May make the engine somewhat harder to balance etc. Anyway, it would be worth getting the bottom end / flywheel / clutch etc balanced properly to help reduce stresses on the engine.
All in all, depending how far you are willing to go, you should see somewhere between 210 and 240 bhp with a decent emerald mapping session. Torque will be good. Longevity? Don't know.
Errrrrr.... Im not going to lie, alot of that went over my head lol. Ive printed off all feedback (much appreciated thank you) and will read up on your suggestions and what would best suit the engine for longevity as i dont really fancy shelling out on rebuilds every 20k.
Will also give dave @ dva an email to see what he suggests...
Thank you for the reponse, hopefully see you on driver training / track soon once car is complete
Will also give dave @ dva an email to see what he suggests...
Thank you for the reponse, hopefully see you on driver training / track soon once car is complete

Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff




