How big is the steering wheel in an S2?
Discussion
1. Straighten steering wheel and try and chock the front wheels to avoid movement.
2. Remove the steering wheel centre pad (simply pulls off) and disconnect horn spade connectors
3. Push back (using a flat blade screwdriver) the locking tabs on the steering column 22mm nut.
4. Put a dot of tipex or the like on the inside top of the splined shaft incase you knock or turn it with the wheel off and lose TDC
5. Undo the 22mm nut (may need deep reach socket) but leave on the last 3 threads of the steering column to avoid getting the wheel in your face when it pops off.
6A. Using a 2 prong puller slide thin jaws in to the oval holes on the back face of the wheel sideways on then rotate them to face inwards, connect to the puller body and pop the wheel off the splined shaft.
6B. if you dont have a puller its a 2 person job. One pulls on the steering wheel and the other taps the centre spline with a hammer.
7. Unscrew the 22mm nut don’t let the spring or lock plate sproing off into hyperspace and careful not to rotate the shaft and loose straight ahead.
8. Once the steering wheel is removed from the splined shaft turn it over and pop off the horn contact plate / slip ring.
9. You will see 4 x M6 Allen headed bolts holding the centre hub to the Lotus steering wheel, remove these 4 bolts and the steering wheel detaches.
10. Attach the 20mm Eliseparts adaptor to the centre hub using the 4 x M6 Allen headed bolts you removed, pop the horn slip ring back on and feed the wire back through if you need to.
10A. If you have a boss kit where the black negative contact is isolated you may need to make up a wire with a spade crimp on one end and a ring crimp the other and file down to sit under one of he the M6 bolts and run the wire up through one of the oval holes on the back plate.
11. Play around with the EP adaptor -> snapoff back plate -> snapoff main body orientation to make sure the holes align as the EP adaptor has several offsets to choose from.
12. Slide the joined EP adaptor and centre hub onto the splined shaft then put the metal lock plate and 22mm nut and tighten to 20lbft (may need a rubber band wrench to hold the column still).
13. Connect the positive wire from the slip ring to the positive on the snap off back plate. Double check negative is earthing - the wire on some kits is isolated and there is no where to attach the connector as in step 10A. As a temporary fix you could just jam the spade between between the mating faces of the eliseparts adaptor and the snapoff back plate but this is NOT RECOMMENDED.
14. Bolt the snap off backing plate to the eliseparts adaptor using 6 countersunk M6 allen screws.
15. Bolt the thin lipped adaptor to the main snap off body using 6 countersunk M6 allen screws lip out to locate the steering wheel.
16. Attach the main body and lipped adaptor to the steering wheel using M5 countersunk allen screws.
17. Connect the horn wiring leads and pop the horn button in (You will not need the silver lipped momo horn adaptor plate).
18. Fit wheel of your choice
A fine selection here: www.antiquesofthesea.com/wheels.html
And a tasty sports version:
Phone for availibility
jamwill79 said:
Hi Marcus,
I got my momo one from eliseparts. To be honest I'm now not sure whether its 300mm or 280mm. I got MSC to fit it when I had some other stuff done.
I got my momo one from eliseparts. To be honest I'm now not sure whether its 300mm or 280mm. I got MSC to fit it when I had some other stuff done.
I was looking at this http://rallynuts.com/motorsport/OMP_S but wondered if I should get a slightly smaller one.
Opinions and alternatives appreciated.
subaqua said:
If you turn the standard wheel thru 180 degrees... it will become apparent that the Lotus wheel is flatter at the bottom than at the top, so there is already an element of the flattening that you see on those wheels, its just less obvious.
You're right, thanks for that. Still have trouble getting my fat thighs underneath even then though ...
S Works said:
WHUFC said:
I really like that, and it has a cut out making it easier to get into. This is important for me as i have now ripped two sets of suit trousers 'falling' into the seat...
PMSL
how do Nick. Not seen you around town in a while. Hope all's well Well thanks Tim. I saw you last week going down Grove Hill Road. I was at the junction of Claremont panicking to get my feet out of the SPD clips on my mountain bike before I went sideways so didn't have time to wave!
It's worth noting that the original S2 wheel is not symmetrical. I had to replace my wheel to get it within reach of my arms (yes, I can't actually reach a standard Lotus wheel!), and I went for a wheel by Momo called the 'tuner' which has exactly the same dimensions as the standard Lotus wheel, both in diameter and ellipticity (is that a word?!).
Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff





PMSL at Janitor. Haven't you got work to do? 