Crack in my clam under the indicator - advice please!
Crack in my clam under the indicator - advice please!
Author
Discussion

RobM77

Original Poster:

35,349 posts

265 months

Wednesday 2nd May 2007
quotequote all
The right hand side indicator unit popped out on the motorway the other day and flapped about breaking itself and scratching my paintwork in the process irked. I need to get the paintwork sorted at some point in the near future, but my priority right now is fitting a new indicator unit in. I've got the new indicator and sealing rubber from Lotus already, but what's preventing me putting it in is that the clam is cracked. It's the part that's out of sight under the indicator unit and the crack is about a centimetre long. It's right where the clip goes in, so I want to repair it properly. Does anyone have any advice for fixing it so I can clip the new indicator in? I thought of using some fibreglass body repair stuff on the underside.



By the way, the line across the top of the picture (on the part of the bonnet that shows) is just the edge of my armourfend The cracks are in the indicator hole.


Edited by RobM77 on Wednesday 2nd May 22:22

tricky 100

954 posts

273 months

Wednesday 2nd May 2007
quotequote all
Hard to say without pics but it sounds like it would be best to use fibreglass matting and resin layed on over the crack as long as it doesn't foul the fitting of the indicator , that would be better than using the chopped strand stuff in the tin .

RobM77

Original Poster:

35,349 posts

265 months

Wednesday 2nd May 2007
quotequote all
tricky 100 said:
Hard to say without pics but it sounds like it would be best to use fibreglass matting and resin layed on over the crack as long as it doesn't foul the fitting of the indicator , that would be better than using the chopped strand stuff in the tin .


Pic posted above

S works

10,166 posts

281 months

Wednesday 2nd May 2007
quotequote all
I'd agree with tricky. Also perhaps use some silkaflex to bond the unit in to prevent this happening again.

AlexT

565 posts

267 months

Thursday 3rd May 2007
quotequote all
I used sikaflex to bond my indicator in too. If you need to change the bulb you can still get to it quite easily from the wheel well.

shangani

3,069 posts

268 months

Thursday 3rd May 2007
quotequote all
Hi Rob, give me a call if you want some help fixing it. I have all the fibreglass stuff needed and spend my life fixing bits if my car (splitters)

stevie111s

123 posts

266 months

Thursday 3rd May 2007
quotequote all
From the pic it looks like the mounting is not actually part of the clam but rather attached to it from the underside after the clam was laid-up. If so then it's unlikely you'll see this crack appear in the clam itself and perhaps nothing to worry about. That's IMHO anyway. As a S1 owner I'm not that familiar with the layup of S2 glass though.

RobM77

Original Poster:

35,349 posts

265 months

Thursday 3rd May 2007
quotequote all
stevie111s said:
From the pic it looks like the mounting is not actually part of the clam but rather attached to it from the underside after the clam was laid-up. If so then it's unlikely you'll see this crack appear in the clam itself and perhaps nothing to worry about. That's IMHO anyway. As a S1 owner I'm not that familiar with the layup of S2 glass though.


If I leave that crack though it might let the new indicator out the next time I go over a bump!

RobM77

Original Poster:

35,349 posts

265 months

Thursday 3rd May 2007
quotequote all
shangani said:
Hi Rob, give me a call if you want some help fixing it. I have all the fibreglass stuff needed and spend my life fixing bits if my car (splitters)


YHM Thanks.

RobM77

Original Poster:

35,349 posts

265 months

Thursday 3rd May 2007
quotequote all
Many thanks to Shangani, who has just very kindly fixed my car!

shangani

3,069 posts

268 months

Thursday 3rd May 2007
quotequote all
Did the indicator fit in OK with the seal in place?

S works

10,166 posts

281 months

Thursday 3rd May 2007
quotequote all
OK, how many beers to fix the holes in the underside of my front clam shang?

shangani

3,069 posts

268 months

Thursday 3rd May 2007
quotequote all
S works said:
OK, how many beers to fix the holes in the underside of my front clam shang?


Tim, take a picture of the damage, which will tell me what I need to fix it. Get me the paint code for your colour car and I can have an aerosol made up locally for about £14 and it should not be a lengthy job when next we meet.

RobM77

Original Poster:

35,349 posts

265 months

Thursday 3rd May 2007
quotequote all
shangani said:
Did the indicator fit in OK with the seal in place?


Yes thanks. It needed quite a bit of sanding to get it to fit, but I think it fits better than the other (Lotus) one now!

RobM77

Original Poster:

35,349 posts

265 months

Thursday 3rd May 2007
quotequote all
Here's Andy's repair:



(compare this with the top image on this thread)

The marks around it are mine, where I'd taped the old indicator back in to stop rain getting in. I'm going to try polishing out the scratches that the flapping indicator caused at the weekend!

RobM77

Original Poster:

35,349 posts

265 months

Friday 4th May 2007
quotequote all
The damage on the front clam has come out as well! I polished it out with some standard car polish:





I'm very pleased!

shangani

3,069 posts

268 months

Friday 4th May 2007
quotequote all
Bling bling.

Good job with the polishing Rob - that has come up well. Sorry to have left so much to be sanded before final fitting.