Discussion
Ok, this is not a "how to" question cos I have done my research on this and seen the wiki and other SELOC and Pistonhead posts on this etc.
What I really want to know is, how EASY is it to change an exhaust? Mine is rotten as a pear and has two great holes in it, either side of the silencer, so has to be changed soon. I have a bid in on eBay for a second-hand Janspeed at the moment (probably shouldn't have said that should I? LOL!) and I have a couple of people who have offered me a couple of good condition second-hand standard exhausts. So I have it covered at the moment. But, to save money, I am going to probably do the work myself with my Dad again and even though I KNOW how to do it, none of this info ever gives me an indication on how EASY its going to be.
Any pointers? Any things I should know that the info out there doesn't tell you about?
You could even give me its ease on a scale of 1 to 10 if you like!! LOL!!
Cheers guys
What I really want to know is, how EASY is it to change an exhaust? Mine is rotten as a pear and has two great holes in it, either side of the silencer, so has to be changed soon. I have a bid in on eBay for a second-hand Janspeed at the moment (probably shouldn't have said that should I? LOL!) and I have a couple of people who have offered me a couple of good condition second-hand standard exhausts. So I have it covered at the moment. But, to save money, I am going to probably do the work myself with my Dad again and even though I KNOW how to do it, none of this info ever gives me an indication on how EASY its going to be.
Any pointers? Any things I should know that the info out there doesn't tell you about?
You could even give me its ease on a scale of 1 to 10 if you like!! LOL!!
Cheers guys
As per S Works I haven't changed an exhaust on an Elise/Exige but I have had the undertray off and I have also changed exhausts on other cars. Assuming all the bolts are reasonably easy to remove on a scale of 1 - 10 with 1 being changing a wheel and 10 changing the engine, the exhaust would pobably be 2 - 3. The problem comes with siezed bolts which will make it more difficult. Use plenty of penetrating fluid and leave it soak in over night. Don't use cheap spanners/sockets
Its certainly not difficult if you are leaving the manifold/flexi in place and just replacing the cat & silencer.
Rusty bolts are the nightmare. Penetrating oil is often next to useless in that situation and if the studs or bolts are seriously corroded, you have to just hope that they shear before they get rounded off!
Is it just the silencer you are replacing? If so, no real difficulties at all.
The cats have studs at one end and nuts/bolts and the other. I'd be tempted to buy a decat pipe and fit that while youre under there. Easier than putting the cat back! Buy two gaskets, a tube of exhaust assembly paste and six nice shiny stainless steel 17mm nuts and bolts before you start and bolting everything together will be a piece of cake.
Rusty bolts are the nightmare. Penetrating oil is often next to useless in that situation and if the studs or bolts are seriously corroded, you have to just hope that they shear before they get rounded off!
Is it just the silencer you are replacing? If so, no real difficulties at all.
The cats have studs at one end and nuts/bolts and the other. I'd be tempted to buy a decat pipe and fit that while youre under there. Easier than putting the cat back! Buy two gaskets, a tube of exhaust assembly paste and six nice shiny stainless steel 17mm nuts and bolts before you start and bolting everything together will be a piece of cake.
Edited by talkwrench on Friday 11th May 11:32
Yep, hardest part is getting the old silencer off as the bolts will be rusted through. Just hacksaw the nut off, will take maybe half an hour and buy the Eliseparts stainless steel exhaust fixings. The rest was easy for a mechanical numpty like me
Only thing I'm not sure about is access, an S2 is easy, the clam stops just under the lights, whereas the S1 clam carries on underneath the car. I've heard it can be awkward, anyone wish to share their experiences?
Only thing I'm not sure about is access, an S2 is easy, the clam stops just under the lights, whereas the S1 clam carries on underneath the car. I've heard it can be awkward, anyone wish to share their experiences?
larinis etc are a lot easier to install, the original exhaust is huge in comparison and takes some prizing to get it out of the small gap. I had to bend the rear clam a little bit to allow it to come free, not sure how hard it is to then get one back in though. Get a larini or something, half the size and better exhaust note.
All good stuff guys! Thanks for that. I need to look more closely at the system as I am not sure which bit is which to be honest, but as a guide for you all, the holes are in the pipes that you can see through the chassis when you have the rear wheels off. The come out of what LOOKS like the silencer. I guess the cats are behind this? I am not sure. Sorry. Bit unclear on this myself so need to study the Service Manual to have a look...........but I think the pipes are coming from the silencer and the holes are in those pipes, just on the bends......
Anyway, I guess the main thing I am looking at is rusted bolts. I HATE this, so will spray everything with penetrating oil about 2 days before and then KEEP spraying to make sure. I know it doesn't always work, which is bloody annoying, but I am sure my Dad will have some ideas if bolts get sheared or broken or something. Will get hold of the replacements beforehand I reckon.
This is all great stuff guys. You lot are invaluable, you know that?!!!
Anyway, I guess the main thing I am looking at is rusted bolts. I HATE this, so will spray everything with penetrating oil about 2 days before and then KEEP spraying to make sure. I know it doesn't always work, which is bloody annoying, but I am sure my Dad will have some ideas if bolts get sheared or broken or something. Will get hold of the replacements beforehand I reckon.
This is all great stuff guys. You lot are invaluable, you know that?!!!

You can get freeze and release from halfrauds, good stuff for rusty bolts. You might also want to get a breaker bar to give a little more leaverage to get the nuts off.
The access to the two bolts at the back of the cat can be little akward to get to. That's it really, not much that it anything difficult. Then you can sit down after, with a nice beer and think of how much cash you've saved.
The access to the two bolts at the back of the cat can be little akward to get to. That's it really, not much that it anything difficult. Then you can sit down after, with a nice beer and think of how much cash you've saved.
Did mine on my S1 including a 4-2-1, which was MUCH trickier than the back box itself (getting the old manifold out means removing engine mounts).
The back box wasn't hard in itself, although it is a bit of a squeeze getting it out without damaging the heat shielding.... but patience will win the day. There's no big difficulty with the job, just a bit of patience needed at times.... leave yourself plenty of time to do it and you'll be fine. Most of the mission with mine was getting it all to fit.... my tailpipes were bent, which was fixed in the end with an angle grinder and a TIG welder
Long story short I think I removed and refitted my system about 10 times before I was 100% happy... mind you, I AM a perfectionist where my Elise is concerned 
The back box wasn't hard in itself, although it is a bit of a squeeze getting it out without damaging the heat shielding.... but patience will win the day. There's no big difficulty with the job, just a bit of patience needed at times.... leave yourself plenty of time to do it and you'll be fine. Most of the mission with mine was getting it all to fit.... my tailpipes were bent, which was fixed in the end with an angle grinder and a TIG welder
Long story short I think I removed and refitted my system about 10 times before I was 100% happy... mind you, I AM a perfectionist where my Elise is concerned 
Esprit said:
...patience will win the day. There's no big difficulty with the job, just a bit of patience needed at times.... leave yourself plenty of time to do it and you'll be fine.
Best advice ever. I'm a terrible *rusher* which is generally why I tend to pay other people to do this kind of thing and do it properly. If I had the space though I would deffo give this kind of thing a go.
Friends of mine replaced my Cat on the Sport 160 before I sold it and I *helped*
It is quite a tight fit but once the Cat is off you can easily manouvre everything I'd imagine. The main thing is having the space to do it, and lots of time so you don't have to panic about getting it done.
Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff


